2008 Peugeot 407 C Dag ESP

7
85
Dynamic stability control (DSC)
When changing wheels (tyres
and rims), make sure that
these are approved.
Normal operation of the ABS
may make itself felt by slight vibrations
of the brake pedal.

In emergency braking, press
very fi rmly without relea sing
the pressure. Operating fault
When a system malfunction occurs,
the warning light comes on accompa-
nied by an audible signal and a mes-
sage on the multifunction display.
Contact a PEUGEOT dealer to have
the system checked.
The DSC offers improved
safety during normal driving
but should not encourage the
driver to take extra risks (late
braking) or drive at very high speeds.
Operation of the system is guaran-
teed on condition that the manufactu-
rer's instructions regarding the wheels
(tyres and rims), the braking compo-
nents, the electronic components and
the PEUGEOT network assembly and
maintenance/repair procedures are
complied with.
Following an impact, have the system
checked by a PEUGEOT dealer.
Warning light on the instrument
panel.
The indicator light comes on.
Deactivation
In exceptional conditions (starting the
vehicle when it is stuck in mud, immo-
bilised in snow, on unstable ground…),
it may prove useful to deactivate the
DSC.

 Press the "ESP OFF" switch, lo-
cated on the centre console.
The switch light and the indicator light
come on: the DSC no longer acts on
the operation of the engine.
Indicator light on the instrument
panel.
Reactivation

 Automatic when the ignition is
switched off,

 Automatic from 30 mph (50 km/h),

 Manual by pressing the switch
again.
Operation of the DSC

7
90
Front side air bags
The side air bags protect the driver
and passengers in the event of a se-
rious side impact in order to limit the
risks of injury to the chest.
Each side air bag is incorporated into
the front seat back.
Activation
The side air bags are deployed inde-
pendently of each other in the event
of a serious side impact applied to
all or part of the side impact zone B ,
perpendicular to the longitudinal cen-
treline of the vehicle on a horizontal
plane directed from the outside to the
inside of the vehicle.
The side air bag infl ates between the
front occupant of the vehicle and the
corresponding door trim pad.
In the event of a malfunction
If this warning light comes on, ac-
companied by an audible signal and a
message on the multifunction display,
contact a PEUGEOT dealer to have
the system checked. The air bags may
no longer be deployed in the event of
a serious impact. Instrument panel warning
light.
* According to country.
Impact detection zones

A. Front impact zone.

B. Side impact zone.
The curtain air bags protect the driver
and passengers in the event of a se-
rious side impact in order to limit the
risks of injury to the head.
Each curtain air bag is incorporated
into the door pillars and the upper part
of the passenger compartment. Activation
It is deployed at the same time as the
corresponding side air bags in the
event of a serious side impact applied
to all or part of the side impact zone
B ,
perpendicular to the longitudinal cen-
treline of the vehicle on a horizontal
plane directed from the outside to the
inside of the vehicle.
The curtain air bag infl ates between
the front or rear occupant of the vehi-
cle and the windows.
In the event of a minor impact
or bump on the side of the
vehicle or if the vehicle rolls
over, the air bag may not be
deployed.
In the event of a front or rear collision,
the air bag is not deployed.

8
93
Gear selection gate

 Move the lever in the gate to select
a position.
The indicator light corresponding to
the position selected appears on the
instrument panel screen.

P ark: to immobilise the vehicle and to
start the engine, with the handbrake on.

R everse: to reverse (select this posi-
tion with the vehicle stationary, engine
at idle).

N eutral: to start the engine and to park,
with the handbrake on.

Note: if position N is inadvertently en-
gaged while driving, allow the engine
to return to idle before engaging posi-
tion D then accelerate.

D rive: to drive in automatic mode.

M anual: to drive selecting the gears.

S: sport programme.

 : snow programme.
'PORSCHE TIPTRONIC SYSTEM' AUTOMATIC GEARBOX
The six speed automatic gearbox
offers, as required, the comfort of the
auto-adaptive programme enhanced
by a selection suited to dynamic
driving conditions: sport, or to driving
on a slippery road: snow.
However, manual selection is still pos-
sible using the gear lever.
Moving Off
With the engine running, move off from
position P :

 to exit position P, it is essential
to press the brake pedal,

 select position R , D or M , then
gradually release the pressure on
the brake pedal; the vehicle moves
off immediately.
To move off from position N :

 with your foot on the brake, release
the handbrake,

 select position R , D or M , then
gradually release the pressure on
the brake pedal; the vehicle moves
off immediately.
Starting the engine

 with the handbrake on, select posi-
tion P or N in the gate,

 turn the ignition key. Always keep your foot on the
brake on a steep incline.
When the engine is at idle,
brakes not applied, if posi-
tion R , D or M is selected, the vehicle
moves even without the accelerator
being pressed.

Do not leave children unsupervised
inside the vehicle, with position
R, D or M selected, with the en-
gine running, as the vehicle moves
even without the accelerator being
pressed.
With the ignition off, if the
lever is not in position P , an
audible signal is heard when
the driver's door is opened, or
after approximately 45 seconds. Move
the lever to position P . The audible
signal ceases.

8
96
CRUISE CONTROL/SPEED LIMITER
Selecting the function

 Place switch 1 in the CRUISE po-
sition. The cruise control is not
yet active and no speed has been
memorised. The display indicates:
Switching the function off

 Place switch 1 in position 0 or

LIMIT to switch the system off.
Note: It is possible to acce-
lerate and drive momentarily
at a speed greater than the
memorised speed. The value
memorised fl ashes. When the acceler-
ator pedal is released, the vehicle will
return to the memorised speed.
Cancelling the memorised speed
If you wish to cancel the memorised
speed:

 Press button 4 or the brake or
clutch pedal. The display indicates
(e.g. at 70 mph (110 km/h)):
Activation/memorising a speed
As soon as you reach the chosen
speed, press button 2 or 3 . This
memorises the speed, which will be
maintained automatically. The display
indicates (e.g. at 70 mph (110 km/h)): On a steep descent, the cruise
control, which does not act on
the brakes, is not able to pre-
vent the vehicle from excee-
ding the programmed speed.
In no circumstances does the cruise control
replace the requirement to respect speed
limits, nor does it replace the need for vigi-
lance and responsibility on the part of the
driver.
We recommend that your feet remain
near the pedals.
Cruise control function
This enables the vehicle to maintain
a steady speed programmed by the
driver
In order for it to be memorised, the
vehicle speed must be greater than
25 mph (40 km/h) with at least fourth
gear engaged (second gear for the
automatic gearbox), with the engine
running .

8

Note: the speed memorised
is cancelled automatically if
the vehicle speed is less than
25 mph (40 km/h), or if the
manual gearbox is in a gear lower than
fourth (second gear for the automatic
gearbox) or if the ESP is activated. Operating check
In the event of a cruise control malfunc-
tion, the memorised speed is erased,
the dashes fl ash for a few seconds:
Contact a PEUGEOT dealer to have
the system checked.
Do not use the cruise control
on slippery roads or in heavy
traffi c.
Changing a memorised speed
To memorise a speed higher than the
previous one, there are two options:
Without using the accelerator:

 press button 3 ;
Using the accelerator:

 exceed the memorised speed until
the required speed is reached,

 press button 2 or 3 .
Recalling the memorised speed
After cancellation, press button 4 . Your
vehicle will return to the last memo-
rised speed. The display indicates
(e.g. at 70 mph (110 km/h)):
Cancelling the memorised speed

 Place switch 1 in position 0 or

LIMIT or switch off the ignition.
To memorise a speed lower than the
previous one:

 press button 2 ;
To prevent the mat from becoming
caught under the pedals:
- ensure that the mat is positioned correctly,
- never fi t one mat on top of another.
Short press: +/- 1 mph (1 km/h)
Long press: +/- 5 mph (5 km/h)
Maintained press: continuous increase
or decrease of the value in steps of
5 mph (5 km/h).

8
98
CRUISE CONTROL/SPEED LIMITER
Selecting the function

 Place switch 1 in the LIMIT po-
sition. The limiter is not yet active.
By default the display indicates:
Switching the function off

 Place switch 1 in position 0 or

CRUISE or switch off the ignition
to switch the system off. The last
speed programmed remains in the
memory.
Memorising a speed
A speed can be memorised without
activation of the limiter.
Pressing buttons 2 and 3 decreases or
increases the speed.
Short press: +/- 1 mph (1 km/h)
Long press: +/- 5 mph (5 km/h)
Maintained press: continuous increase
or decrease of the value in steps of
5 mph (5 km/h). Activation/deactivation of the
limiter
Pressing button
4 activates the limiter,
pressing this button again deactivates it.
When the limiter is active, the display
indicates (e.g. at 70 mph (110 km/h)):

The operations must be
carried out with the engine
running. On a steep descent or if the
driver accelerates sharply, the
speed limiter, which does not
act on the brakes, is not able
to prevent the vehicle from exceeding
the programmed speed.
In no circumstances does the speed
limiter replace the requirement to re-
spect speed limits, nor does it replace
the need for vigilance and responsibil-
ity on the part of the driver.
The driver must remain vigilant and
stay in complete control of his vehicle.
Limiter function
This prevents the vehicle speed ex-
ceeding the speed programmed by
the driver (minimum speed of 18 mph
(30 km/h)).

8
102
TYRE UNDER-INFLATION DETECTION
Sensors check the tyre pressure dur-
ing driving and trigger a warning in the
event of malfunction.
Pressure Check With the ignition on and the
vehicle having been stationary
for approximately 15 minutes,
and after the engine oil level,
this indicator light comes on
on the instrument panel screen to indi-
cate that the system is measuring the
tyre pressures.
Pressure OK
This indicator light comes
on on the instrument panel
screen if all of the tyre pres-
sure values measured are
correct.
If this indicator light does not appear,
contact a PEUGEOT dealer to have
the system checked. Puncture
This warning light, accom-
panied by the audible signal
and the message on the
multi-function display loca-
ting the wheel concerned, is
followed by illumination of the STOP
warning light.
Stop immediately, avoiding any sud-
den movement of the steering wheel
and the brakes.
Change the damaged wheel (punc-
tured or very defl ated tyre), and have
the tyre pressure checked as soon as
possible.

Note: this message is also dis-
played when one of the wheels
is away from the vehicle (be-
ing repaired) or when one or
more wheels without a sensor
are fi tted. All repairs and changing of
tyres on a wheel fi tted with this
system must be carried out by
a PEUGEOT dealer.
If, when changing a tyre, you install a
wheel which is not detected by your
vehicle, you must have the system
reinitialised by a PEUGEOT dealer.
The tyre under-infl ation detection sys-
tem is an aid to driving which does not
replace the need for the driver to be
vigilant or to drive responsibly.
This system does not eliminate the
need to have the tyre pressure checked
regularly (see manufacturer's label) to
ensure that the optimum dynamic per-
formance of the vehicle is maintained
and prevent premature wear of the
tyres, particularly in arduous driving
conditions (heavy load, high speed).
The tyre pressures must be checked
cold, at least once a month. Remember
to check the pressure of the spare
wheel.
The tyre under-infl ation detection sys-
tem may experience temporary inter-
ference due to radioelectric emissions
on a frequency close to that used by
the system.
Flat tyre
This warning light is accom-
panied by the audible si gnal
and the message on the
multi-function display loca-
ting the wheel concerned.
If this warning light comes on, have
the tyre pressure checked as soon as
possible. Sensor(s) not detected or faulty
This warning light is accom-
panied by the audible si gnal
and the message on the
multi-function display which
indicates that under-infl ation
detection is absent from one (or seve-
ral) wheel(s) or that there is a fault in
the system.
Contact a PEUGEOT dealer to replace
the faulty sensor(s).

1010
110
After changing the wheel:
- have the tightening of the bolts and the tyre pressure of the spare wheel
checked as soon as possible.
-
have the punctured wheel repaired and
refi t it to the vehicle as soon as possible.
- have the spare wheel checked and replace it in its boot recess.
Fitting a wheel

 Position the wheel.

 Tighten the bolts by hand.

 Partly tighten the bolts using the
wheelbrace 1 .

 Fold the jack 2 and remove it.

 Fully tighten the bolts using the
wheelbrace 1 .

 For vehicles with alloy wheels, refi t
the covers.

 Put the tool holder back in position.
This helps to keep the boot fl oor in its
correct position, to prevent any defor-
mation of the fl oor when loaded.

 Tighten the spare wheel securing
strap to prevent noise and for your
safety in the event of impact.

Reminder: for your safety, always
change a wheel:
- on level, stable, non-slippery ground,
- with the handbrake applied,
- with fi rst or reverse gear engaged (po- sition P for the automatic gearbox),
- never go underneath a vehicle which is supported only by a jack.
Tools available
The following tools are located in
the holder in the centre of the spare
wheel:

1. Wheelbrace.
Permits removal of the wheel trim and removal of the wheel securing
bolts.

2. Jack with integrated handle.
Permits raising of the vehicle.

3. Removable towing eye.
See corresponding section.

4. Bolt cover tool. Permits removal of
the bolt protectors (covers) on alloy
wheels. Removal

 For vehicles with alloy wheels,
remove the covers using tool 4 .

 Loosen the wheel bolts.

 Place the jack 2 in one of the four
locations underneath the vehicle
(the nearest one to the wheel to be
changed).

 Extend the jack 2 until its base is in
contact with the ground.

 Unscrew the bolts and remove the
wheel.