2008 Peugeot 308 SW BL Owner's Manual

!
!
104
LAYOUT To avoid any risk of jamming of the
pedals:
- only use mats which are suited to the fi xings already present in
the vehicle; it is imperative that
these are used,
- never fi t one mat on top of another
MAT
Removable component which protects
the carpet against exterior dirt. Refitting
To refi t the mat on the driver’s side:

 position the mat correctly,

 refi t the fi xings by pressing,

 check that the mat is secured
correctly.
Fitting
When fi tting the mat for the fi rst time,
use only the fi xings provided in the wal-
let attached.
Removal
To remove the mat on the driver’s side:

 move the seat as far back as
possible,

 unclip the fi xings

 remove the mat.
STORAGE DRAWERS *
Opening


Raise the front of the drawer and pull it.
* Except on electric seat.
Do not place heavy objects in the
drawers.
Removal

 Bring the drawer to the end of its
travel.

 Press the ends of the slides.

 Raise the drawer and pull it fully.
Refitting

 Engage the drawer in its slides.

 At the end of its travel, press on the
top of the drawer to secure it.

!
105
LAYOUT
REAR ARMREST SKI FLAP
Opening

 Lower the rear armrest.

 Pull the fl ap handle downwards.

 Lower the fl ap.

 Load the objects from inside the
boot.

 Lower the rear armrest for a more
comfortable position.

 Raise the cover to gain access to its
storage compartment.
This has a storage tray, two can holders
and two pen holders.
"AIRCRAFT" TYPE TABLES

 To use the table, raise it fully until it
locks in the high position.

 To store the table, lower it, passing
the point of resistance, to the low
position.
On the passenger side, do not for-
get to fold the "aircraft" type table
before placing the seat in the table
position.
Do not place hard or heavy objects
on the table. They could become
dangerous projectiles in the event
of emergency braking or impact.
Comfort and storage device for the rear
passengers.
Device for storing and transporting long
objects. Installed on the back of each front seat,
these allow you to set down objects and
each is equipped with a can holder.

LAYOUT BOOT LAYOUT

1. Rear shelf or shelf with integrated
storage compartment
(see details on following page)

2. Hooks
(see details on following page)

3. 12 V accessories socket
(see details on following page)

4. Stowing rings

5. Luggage retaining net
(see details on following page)

6. Movable straps
(see details on following page)

7. Luggage retaining strap

8. Enclosed storage tray

9. Open storage tray

10. Storage box
(see details on following page)

i
107
LAYOUT
To remove the shelf:

 unhook the two cords,

 raise the shelf slightly, then remove it.
Rear shelf
When changing a wheel
An additional hook, under the shelf,
permits easy access to the spare
wheel by retaining the boot carpet
by means of its cord.
To remove the shelf:

 unhook the two cords,

 raise the shelf slightly, then remove it.
Shelf with integrated storage
compartment
This permits the storage of any object so
that it cannot be seen from the outside
and without hindering rearward visibility.
The hooks permit the securing of shop-
ping bags.
Hooks
There are several options for storing the
shelf:
- either upright behind the front seats,
- or upright behind the rear seats using one of the movable straps. There are several options for storing the
shelf:
- either upright behind the front
seats,
- or upright behind the rear seats using one of the movable straps.

 To open the cover, from inside
or outside, raise one of the two
handles.

 To close the cover, fi rst raise the
handle.

 To remove the cover, raise both
handles at the same time.

108
LAYOUT Luggage retaining net
Hooked onto the stowing rings, this en-
ables you to secure your luggage.

 Raise the boot carpet to gain access
to the storage box.
This has areas for storing a box of spare
bulbs, a fi rst aid kit, a puncture repair
kit, two warning triangles, ...
Storage box

 In order to connect a 12 V accessory
(max power: 100 Watts), remove
the cap and connect the appropriate
adaptor.

 Turn the key to the ignition position.
12 V accessories socket
There are three possible positions:
- fl at at the bottom of the boot,
- horizontal at the rear shelf,
- vertical at the back of the rear seats.
Movable straps
Hooked onto the stowing rings, they
permit securing of your luggage.

109
LAYOUT
BOOT LAYOUT

1. Load space cover
(see details on following page)

2. 12 V accessories socket
(see details on following page)

3. Hooks
(see details on following page)

4. Stowing rings

5. Luggage retaining net
(see details on following page)

6. Storage tray

7. High load retaining net
(see details on following page)

8. Luggage retaining strap

9. Storage nets

i
110
LAYOUT
Load space cover
This consists of four sections three of
which can be folded back on each other.
There are several options for storing the
load space cover:
- either folded back on itself near the rear seats (1),
- or folded back on itself and stored in a location provided under the rear
seats (2).
To fold it from the boot:

 unclip the load space cover from its
side supports,

 take hold of the load space cover by
its handle A ,

 fold it concertina-style to the rear
seats.
To unfold it from the boot:

 take hold of the load space cover by
its handle A ,

 unfold it to the boot pillars,

 clip the load space cover on its side
supports. Luggage retaining net
Hooked onto the stowing rings, this en-
ables you to secure your luggage to the
bottom of the boot.
Hooks
The hooks permit the securing of shop-
ping bags.
Maximum loads
7.5 kg, load space cover unfolded
with high load retaining net at row 2.

i
i
111
LAYOUT
High load retaining net
Hooked onto the special upper and low-
er fi xings, this permits use of the entire
loading volume up to the roof:
- behind the rear seats (row 2),
- behind the front seats (row 1) when the rear seats are folded.
To use it in row 1:

 open the covers of the upper fi xings 1 ,

 unroll the high load retaining net,

 position one of the ends of the net’s
metal bar in the corresponding upper
fi xing 1 , then do the same with the
other end,

 slacken the straps fully,

 fi x the snap hook of each of the
straps on the corresponding bar 3 ,
located under the cushion of the
rear seats,

 fold the rear seats,

 tighten the straps,

 check that the net is hooked and
tightened correctly. To use it in row 2:

 fold or remove the load space
cover,

 open the covers of the upper fi xings 2 ,

 unroll the high load retaining net,

 position one of the ends of the net’s
metal bar in the corresponding upper
fi xing 2 , then do the same with the
other end,

 fi x the snap hook of each of the
straps in the corresponding ring 4 ,
located on the rear seats mechanism
support,

 tighten the straps,

 check that the net is hooked and
tightened correctly.
When positioning the net, check
that the strap loops are visible from
the boot; this will make slackening
or tightening easier.
This net can be stored in the stor-
age tray on the fl oor.