2008 Peugeot 206 SW Dag display
[x] Cancel search: displayPage 68 of 123
VISIBILITY
64 -
" F o l l o w m e h o m e " l i g h t i n g
When you leave your vehicle, the
side lights and dipped headlamps
can be left on for approximately
30 seconds.
To do this:
- place the key in the STOP
position,
- place the lights stalk in the 0
position,
- l a s h t h e h e a d l a m p s ,
- get out of the vehicle and lock it. A U T O M A T I C S W I T C H I N G O N
OF LIGHTS
The side lights and dipped beam
headlamps switch on automatically if
the light is poor and when the wind-
screen wipers operate continuously
and switch off when the light becomes
bright enough or the windscreen wip-
ers are switched off.
I n f o g g y w e a t h e r o r i n s n o w , t h e
b r i g h t n e s s s e n s o r c a n d e t e c t s u f i -
c i e n t l i g h t , t h e l i g h t s w i l l n o t c o m e
o n a u t o m a t i c a l l y . I f n e c e s s a r y ,
t h e d i p p e d h e a d l a m p s m u s t b e
s w i t c h e d o n m a n u a l l y .
This function is active when the vehi-
cle is supplied to the customer.
To disarm or activate the function:
- Place the key in the accessories position (1st notch),
- Place the lights stalk in the AUTO/0 position,
- Press the end of the lights stalk for more than four seconds.
D o n o t c o v e r t h e b r i g h t n e s s s e n -
s o r , c o u p l e d w i t h t h e r a i n s e n s o r ,
l o c a t e d i n t h e c e n t r e o f t h e w i n d -
s c r e e n , b e h i n d t h e i n t e r i o r m i r r o r .
I t i s u s e d f o r a u t o m a t i c s w i t c h i n g
o n o f t h e l i g h t s . O p e r a t i n g c h e c k
In good or rainy weather,
both day and night, the
front fog lamps and the
rear fog lamp are dazzling
and are prohibited.
Do not forget to switch them off
when they are no longer needed.
D i r e c t i o n i n d i c a t o r s
( l a s h e r s )
L e f t : downwards.
R i g h t : upwards. D i s a r m i n g
The disarmed function is accompa-
nied by an audible signal.
When the driver uses the manual
lighting controls, the function is tem-
porarily disarmed.
I f t h e b r i g h t n e s s s e n s o r d o e s n o t
f u n c t i o n c o r r e c t l y
, the lights come
on accompanied by an audible signal
and a message on the multifunction
display.
Consult a PEUGEOT dealer.
A c t i v a t i o n
The activated function is accompa-
nied by an audible signal and a mes-
sage on the multifunction display.
Page 70 of 123
VISIBILITY
66 -
A u t o m a t i c w i n d s c r e e n
w i p e r s
In the AUTO position, the windscreen
wipers operate automatically and
a d a p t t h e i r s p e e d t o t h e i n t e n s i t y
o f t h e r a i n f a l l . Do not cover the rain sen-
sor located on the wind-
screen behind the interior
mirror.
When using an automatic car
wash, switch off the ignition or
check that the wiper stalk is not in
the AUTO position.
In winter, it is advisable to wait
for the windscreen to completely
clear of ice before operating the
automatic wipe. R e a r s c r e e n w i p e r
R e a r s c r e e n w a s hTurn ring
A t o t h e i r s t n o t c h
for intermittent wiping.
I f t h e i g n i t i o n i s s w i t c h e d
o f f , i t i s n e c e s s a r y t o r e a c -
t i v a t e t h e c o n t r o l e a c h t i m e . To do
this, move the stalk to any position,
then move it back to the required po-
sition.
Turn ring A p a s t t h e i r s t
notch; the screen wash then
t h e w i p e r o p e r a t e f o r a i x e d
period.
O p e r a t i n g c h e c k
A c t i v a t i o n
Activation of the function is accom-
panied by a message on the multi-
function display.
I n t h e e v e n t o f m a l f u n c t i o n
, the
driver is informed by an audible sig-
nal.
In the AUTO position, the wind-
screen wiper will operate in intermit-
tent mode.
Contact a PEUGEOT dealer to have
the system checked. A u t o m a t i c r e a r s c r e e n w i p e r
When the windscreen wipers control
is activated and you engage reverse
gear, the rear screen wiper operates
intermittently.
N o t e :
if you use a bicycle carrier,
consult a PEUGEOT dealer to have
this function deactivated or install a
s p e c i i c b i c y c l e c a r r i e r a p p r o v e d b y
PEUGEOT.
Page 71 of 123
67
VISIBILITY
-
T R I P C O M P U T E R
Pressing the button on the end of the
w a s h / w i p e s t a l k enables the follow-
ing data to be displayed:
D i s p l a y B
- the range,
- the distance travelled,
- the average consumption,
- the current consumption,
- the average speed. Z e r o r e s e t
Press the stalk for more than two
seconds.
Range
This shows the distance that can still
be covered with the fuel remaining in
the tank.
N o t e :
t h i s i g u r e m a y i n c r e a s e i f
there is a change in the style of driv-
ing or the road surface, producing a
s i g n i i c a n t d r o p i n c u r r e n t c o n s u m p -
tion.
When the range is less than 20 miles
(30 km), three segments are dis-
p l a y e d . A f t e r i l l i n g w i t h f u e l , t h e
range is displayed when it exceeds
60 miles (100 km).
If horizontal segments are displayed
for long periods instead of digits,
contact a PEUGEOT dealer. D i s t a n c e t r a v e l l e d
This indicates the distance travelled
since the computer was last set to
zero.
A v e r a g e c o n s u m p t i o n
This is the average fuel consumption
since the computer was last set to
zero. C u r r e n t c o n s u m p t i o n
This is the average quantity of fuel
consumed during the last few sec-
onds.
This function is displayed only when
the vehicle is travelling at a speed
greater than 20 mph (30 km/h).
A v e r a g e s p e e d
This is the average speed calculated
since the computer was last set to
zero (with the ignition on).
Page 79 of 123
75
DRIVING
-
Automatic operation
Automatic changing of the four
gears:
F select position D in the gate.
The gearbox always selects the most
suitable gear according to the follow-
ing parameters:
- t h e r o a d p r o i l e ,
- the vehicle load.
The gearbox is then operating in
auto-adaptive mode, without any ac-
tion on your part. If you take your foot off the accel-
erator suddenly, the gearbox will not
change to a higher gear for reasons
of safety.
Manual operation
Manual
changing of the four gears :
F select position M in the gate,
F push the lever to the + sign to
change to a higher gear,
F pull the lever to the - sign to
change to a lower gear.
You can change from position D
(driving in automatic mode) to posi-
tion M (driving in manual mode) at
any time.
WARNING
Never select position N when the ve-
hicle is moving.
Never select positions P or R unless
the vehicle is stationary.
Never change between positions to op-
timise braking on a slippery surface.
Notes
For immediate maximum accelera-
tion without touching the gear lever,
press the accelerator pedal down as
far as it will go (kickdown). The gear-
box will automatically change down
or maintain the gear selected until
maximum engine speed is reached.
When the brake is applied, the gear-
box will automatically change down
i n o r d e r t o p r o v i d e e f i c i e n t e n g i n e
braking. Sport and snow programmes
In addition to the auto-adaptive pro-
gramme, there are two special pro-
grammes.
The programme is displayed on the
instrument panel screen.
Sport programme
F
Press button S once the engine
has been started.
The gearbox automatically favours
sporty driving and more dynamic ac-
celeration.
Snow programme
This programme improves starting
and drive when traction is poor.
F Press button T once the engine
has been started.
The gearbox adapts to driving on
slippery roads.
Note: you can return to the auto-
adaptive programme at any time.
F Press button S or T again to
switch off the programme you
are in. Notes
It is only possible to change from one
gear to another if the vehicle speed
and engine speed permit. If they do
not, the vehicle will operate tempo-
rarily in automatic mode.
When the vehicle is stationary or
moving very slowly, the gearbox au-
tomatically selects gear
M1.
Programmes S (sport) and T (snow)
do not operate in manual mode.
Page 80 of 123
DRIVING
76 -
HANDBRAKE
Operating abnormality
Any operating abnormality is indi-
cated by an audible signal, accom-
panied by the message 'Automatic
gear fault' on the multi-function dis-
play, by a "-" a n d l a s h i n g o f t h e
Sport and Snow warning lights on the
instrument panel display.
In this situation the gearbox oper-
ates in downgrade mode (locked in
3rd gear). You may feel a substan-
tial knock when changing from P to
R and from N to R (this will not cause
any damage to the gearbox).
Do not exceed 60 mph (100 km/h),
respecting local speed limits.
Consult a PEUGEOT dealer.
I f t h e b a t t e r y i s l a t a n d t h e
lever is in position P, it will
be impossible to change
to another position.
In particular, do not force the lever
or there is a risk the gearbox may
be damaged. When the vehicle is be-
ing driven, illumination of
this warning light and of the
STOP
warning light, accom-
panied by an audible signal
and a message on the multifunction
display, indicates that the handbrake
is still on or has not been properly
released.
When parking on a slope,
direct your wheels to im-
mobilise them against the
pavement, pull the hand-
brake and engage a gear.
Applying
Pull the handbrake to immobilise
your vehicle.
Releasing
Pull on the handle and press the but-
ton to release the handbrake.
Page 81 of 123
DRIVING
76 -
HANDBRAKE
Operating abnormality
Any operating abnormality is indi-
cated by an audible signal, accom-
panied by the message 'Automatic
gear fault' on the multi-function dis-
play, by a "-" a n d l a s h i n g o f t h e
Sport and Snow warning lights on the
instrument panel display.
In this situation the gearbox oper-
ates in downgrade mode (locked in
3rd gear). You may feel a substan-
tial knock when changing from P to
R and from N to R (this will not cause
any damage to the gearbox).
Do not exceed 60 mph (100 km/h),
respecting local speed limits.
Consult a PEUGEOT dealer.
I f t h e b a t t e r y i s l a t a n d t h e
lever is in position P, it will
be impossible to change
to another position.
In particular, do not force the lever
or there is a risk the gearbox may
be damaged. When the vehicle is be-
ing driven, illumination of
this warning light and of the
STOP
warning light, accom-
panied by an audible signal
and a message on the multifunction
display, indicates that the handbrake
is still on or has not been properly
released.
When parking on a slope,
direct your wheels to im-
mobilise them against the
pavement, pull the hand-
brake and engage a gear.
Applying
Pull the handbrake to immobilise
your vehicle.
Releasing
Pull on the handle and press the but-
ton to release the handbrake.
Page 82 of 123
77
DRIVING
-
SPEED LIMITER
This speed limiter, of the new gener-
ation, has a display on the instrument
panel to indicate the programmed
speed.
It prevents exceeding of the vehicle
speed programmed by the driver.
When the programmed speed is
reached, pressing the accelerator
pedal no longer has any effect.
The limiter operates with a pro-
grammed speed of at least 18 mph
approx. (30 km/h); it remains active
regardless of any action on the brake
and clutch pedals.
The operating actions must be
carried out: - when stationary, with the
engine running,
or - with the vehicle moving. The indicator light on the in-
strument panel comes on at
the same time.
Instrument panel display
When the speed limiter function is
active, pressing this button displays
the distance recorders.
After a few seconds or when this but-
ton is pressed again, the display re-
turns to the speed limiter function.
Selecting the function
F
Place the dial 1 in the LIMIT
position. The limiter is not yet
active. By default, the display
indicates: Storing a speed
A speed can be stored without acti-
vating the limiter.
Press buttons
2 and 3 b r i e l y t o d e -
crease or increase by 1 mph (1 km/h).
An extended press decreases or in-
creases by 5 mph (5 km/h).
A maintained press decreases or in-
creases the programmed speed in
steps of 5 mph (5 km/h).
Activating / deactivating the
limiter
Pressing button 4 once activates the
limiter, pressing the button again de-
activates it.
When the limiter is active, the display
indicates (e.g. at 70 mph (110 km/h)):
Page 84 of 123
79
DRIVING
-
CRUISE CONTROL
This cruise control, of the new gene-
ration, has a display on the instru-
ment panel to indicate the memorised
reference speed.
It enables the vehicle to maintain a
steady speed programmed by the
driver.
In order for it to be memorised or ac-
tivated, the vehicle speed must be
greater than 24 mph approx. (40 km/h)
with at least fourth gear engaged for
v e h i c l e s i t t e d w i t h a m a n u a l g e a r b o x .
O n v e h i c l e s i t t e d w i t h a n a u t o m a t i c
gearbox, the lever must be in po-
sition D at a speed greater than
24 mph approx. (40 km/h), or in
at least second gear in sequential
mode. The indicator light on the in-
strument panel comes on at
the same time.
Instrument panel display
When the cruise control function is
activated, pressing this button ena-
bles you to display the distance re-
corders.
After a few seconds or when this but-
ton is pressed again, the display re-
turns to the cruise control function.
Selecting the function
F
Place switch 1 in the CRUISE
position. The cruise control is
not yet active and no speed has
been memorised. The display
indicates in succession: First activation / memorising a
reference speed
As soon as you reach the chosen
speed, press button
2 or 3. This
memorises the speed and the display
indicates (e.g. at 70 mph (110 km/h)):
Note : It is possible to accelerate and
drive momentarily at a speed greater
than the memorised speed. The value
m e m o r i s e d l a s h e s . W h e n t h e a c c e l e -
rator pedal is released, the vehicle
returns to the memorised speed.
Cancelling the cruise control
If you wish to cancel the cruise control:
F Press button 4 or the brake or
clutch pedal.
The display indicates (e.g. at 70 mph
(110 km/h)):
The indicator light on the instrument
panel switches off.