2008 Peugeot 206 S Dag display
[x] Cancel search: displayPage 28 of 103
29AUDIO EQUIPMENT-
RADIO Selecting radio mode
Selecting a waveband
Adjusting the front/rear sound
distribution (Fader)
When
"FAD" is displayed, press but-
ton I or J .
Button I increases the volume in the
front.
Button J increases the volume in the
rear.
Adjusting the right/left sound
distribution (Balance)
When "BAL" is displayed, press but-
ton I or J .
Button I increases the volume on the
right-hand side.
Button J increases the volume on the
left-hand side.
Automatic volume correction
This function enables the volume to
be automatically adjusted depending
on the level of noise produced by the
speed of the vehicle.
Press buttons I or J to switch the
function on or off. Press button
R .
Press button R brief-
ly to select the FM1,
FM2 FMast and AM
wavebands.
Notes on radio reception
Your car radio is subject to phenome-
na which do not affect domestic radio
sets. Both AM (MW/LW) and FM re-
ception are subject to various forms
o f i n t e r f e r e n c e . T h i s i s n o r e fl e c t i o n
on the quality of the equipment, but
is due to the nature of the signals and
the way in which they are transmit-
ted.
On MW/LW, interference may be
noticed when passing under high
voltage power lines or bridges, or in
tunnels.
On FM, interference may be the result
of increasing distance from the trans-
m i t t e r , d e fl e c t i o n o f t h e s i g n a l s b y o b -
stacles (mountains, hills, buildings,
etc.), or of being in an area which is
not covered by a transmitter.
Page 29 of 103
AUDIO EQUIPMENT
30 -
Manual station search
Press the "MAN" button.
B r i e fl y p r e s s b u t t o n L or N to in-
crease or decrease the frequency
displayed.
By continuing to press the button in
the direction selected, you will obtain
continuous scrolling of the frequency.
The scrolling stops as soon as the
button is released.
Pressing the "MAN" button again
returns you to automatic station
search. Automatic storing of FM stations
in the memory (autostore)
Your radio automatically stores the 6
stations with the strongest signal in
FM . These stations are stored in the
FMast waveband.
I f i t i s n o t p o s s i b l e t o fi n d 6 s t a t i o n s ,
the remaining memories are empty.
Automatic station search
Manual storing of stations in the
memory
Select the station required.
Press one of the buttons "1" to "6"
for more than two seconds.
The sound stops then becomes audi-
b l e a g a i n , c o n fi r m i n g t h a t t h e s t a t i o n
has been stored in the memory. Recalling stations stored in the
memory
F o r e a c h w a v e b a n d , b r i e fl y p r e s s
buttons
"1" to "6" to recall the cor-
responding station.
B r i e fl y p r e s s b u t t o n
L or N to search
for the station immediately above or
below. By continuing to press the
button in the direction selected, you
will obtain continuous scrolling of the
frequency.
T h e s c r o l l i n g s t o p s a t t h e fi r s t s t a -
tion found as soon as the button is
released.
If the TA t r a f fi c p r o g r a m m e i s s e l e c t -
ed, only stations broadcasting this
type of programme are selected.
S e a r c h i n g f o r a s t a t i o n o c c u r s fi r s t i n
"LO" sensitivity (selection of the most
powerful transmitters) during scan-
ning of the waveband, then in "DX"
sensitivity (selection of the weakest
and most distant transmitters).
To make a direct search in "DX" sen-
sitivity, press button L or N twice. Press and hold button
R for more than two
seconds.
Page 30 of 103
31AUDIO EQUIPMENT-
RDS T r a f fi c i n f o r m a t i o n p r o g r a m m e Regional following mode
When they are part of a network, cer-
tain stations broadcast regional pro-
grammes in the various areas they
serve. With regional following mode
you can keep listening to the same
programme.
Press the "RDS" button for more
than two seconds to switch the func-
tion on or off.
RDS station following
The display indicates the name of the
station selected. The radio is contin-
ually searching for the station which
has the best reception and which is
transmitting the same programme. Press the
"TA" button
to switch the function
on or off.
B r i e fl y p r e s s t h e "RDS"
button to switch the
function on or off.
The multifunction display will show:
- "RDS" if the function is selected.
- "(RDS)" if the function is
selected but not available.
Using the RDS (Radio Data
System) function on FM
Radio Data System allows you to
continue listening to the same sta-
tion, whatever frequency it is using
for the region you are going through.
The multifunction display will show:
-
"TA" if the function is selected,
- "(TA)" if the function is selected
but not available.
A n y t r a f fi c i n f o r m a t i o n fl a s h w i l l b e
given priority, whatever source you
are listening to (radio, cassette or CD
changer).
If you wish to interrupt a message,
press the "TA" button; this switches
the function off.
N o t e : t h e v o l u m e o f t r a f fi c i n f o r m a -
tion announcements is independ-
ent of the volume of normal radio
listening. You can adjust it using
the volume button. The setting will
be stored and will be used when
the next messages are broadcast.
Page 31 of 103
AUDIO EQUIPMENT
32 -
EON system
This connects stations which are part
of the same network. It enables the
b r o a d c a s t o f t r a f fi c i n f o r m a t i o n o r a
PTY programme, by a station that is
part of the same network as the sta-
tion to which you are listening.
This service is available when you
have selected the TA t r a f fi c i n f o r m a -
tion programme or the PTY function.
PTY function
This allows you to listen to stations broad-
c a s t i n g a s p e c i fi c t y p e o f p r o g r a m m e
(news, culture, sport, rock, etc.).
To search for a
PTY programme:
With FM selected,
press the "TA" but-
ton for two seconds to
switch this function on
or off. - select the
PTY function,
- b r i e fl y p r e s s b u t t o n L or N to
scroll down the list of the various
types of programmes offered.
- when the programme of your choice is displayed, keep button
L or N pressed for two seconds
to carry out an automatic search
(after an automatic search the
PTY function is switched off).
In PTY mode the different types of
programmes can be stored in the
memory. To do this, press the prese-
lection buttons "1" to "6" for two
s e c o n d s . B r i e fl y p r e s s t h e c o r r e -
sponding button to recall the type of
programme stored in the memory.
Page 41 of 103
COMFORT42 -
AUTOMATIC AIR CONDITIONING
The air conditioning can only operate when the engine is running.
Automatic operation 2. Control by the AUTO programme
Press the "AUTO" b u t t o n .
We recommend that you use
this mode: it provides opti-
mised automatic control of
all of the functions, passenger com-
p a r t m e n t t e m p e r a t u r e , a i r fl o w , a i r
d i s t r i b u t i o n a n d a i r r e c i r c u l a t i o n , i n
accordance with the comfort value
that you have chosen. This system is
designed to operate effectively in all
seasons, with the windows closed.
Note: for your comfort, the values set
when the engine is switched off are re-
tained on re-starting if the temperature
in the passenger compartment has not
c h a n g e d s i g n i fi c a n t l y ; o t h e r w i s e , o p e -
ration resumes in automatic mode.
Manual operation
If you wish, you can make a different
c h o i c e f r o m t h a t o f f e r e d b y t h e s y s -
t e m b y c h a n g i n g a s e t t i n g . T h e o t h e r
f u n c t i o n s w i l l s t i l l b e c o n t r o l l e d a u t o -
matically.
Pressing the AUTO b u t t o n r e t u r n s
the system to completely automatic
operation.
1. Temperature adjustment
The value indicated on the
display corresponds to a
level of comfort and not to
a temperature in degrees
Celsius or Fahrenheit.
Press the arrows 1 (up and down) to
change this value. A setting around
2 1 e n a b l e s a c o m f o r t a b l e t e m p e r a -
t u r e t o b e o b t a i n e d . When the engine is cold, to
prevent too great a distri-
b u t i o n o f c o l d a i r , t h e v e n -
tilation will only reach its
optimum level gradually.
On entering the vehicle, if the interior
temperature is much colder or warmer
t h a n i s c o m f o r t a b l e , t h e r e i s n o n e e d
to change the value displayed in
o r d e r t o r e a c h t h e r e q u i r e d l e v e l o f
comfort. The system eliminates the
temperature difference automatically
a n d a s q u i c k l y a s p o s s i b l e .
Page 42 of 103
43COMFORT-
3. Air conditioning On/Off P r e s s t h i s b u t t o n t o s t o p a i r
cooling.
4. Air distribution P r e s s i n g t h i s b u t t o n s e v e r a l
t i m e s i n s u c c e s s i o n e n a b l e s
t h e a i r fl o w t o b e d i r e c t e d i n
turn towards:
- the windscreen (de-icing or demisting),
- the windscreen and the footwells,
- the footwells,
- the centre and side vents and the footwells,
- the centre and side vents. 5 . A i r fl o w
P r e s s b u t t o n s "+" and
"-" respectively to in-
crease or decrease
t h e a i r fl o w .
6. Air intake/Air recirculation 7 . S w i t c h i n g t h e s y s t e m o f f
The OFF b u t t o n s w i t c h e s o f f
all the functions of the sys-
tem.
Temperature-related comfort
and demisting are no longer guaran-
t e e d b u t a s l i g h t fl o w o f a i r i s m a i n -
tained.
Pressing the OFF , AUTO , or "visi-
bility" b u t t o n a g a i n r e a c t i v a t e s t h e
s y s t e m w i t h t h e v a l u e s s e t b e f o r e i t
was switched off.
Note: i f y o u w i s h t o c u t o f f t h e fl o w
of air completely, press the air intake
b u t t o n 7 .
P r e s s t h i s b u t t o n f o r r e c i r -
culation of the interior air.
Recirculation, shown on the
d i s p l a y , e n a b l e s t h e p a s -
s e n g e r c o m p a r t m e n t t o b e i n s u l a t e d
from exterior odours and smoke.
Avoid prolonged recirculation of inte-
rior air (risk of condensation and de-
t e r i o r a t i o n o f t h e a i r q u a l i t y ) .
P r e s s t h e b u t t o n a g a i n t o r e s u m e a u -
tomatic management of the intake of
air.
Notes
To prevent condensation on the in-
side of the vehicle in cold or wet
weather, you are advised to avoid
using the ECO mode.
To guarantee correct operation of
your air conditioning system, we also
recommend that you have it checked
regularly.
T h e s y m b o l
ECO is displayed.
Automatic operation of the air condi-
t i o n i n g i s r e s u m e d w h e n t h e b u t t o n
i s p r e s s e d a g a i n . T h e s y m b o l A/C is
displayed.
Page 71 of 103
69DRIVING-
Automatic operation
Automatic changing of the four
gears:
select position D in the gate.
The gearbox always selects the most
suitable gear according to the follow-
ing parameters:
- t h e r o a d p r o fi l e ,
- the vehicle load.
The gearbox is then operating in
auto-adaptive mode, without any ac-
tion on your part. If you take your foot off the accel-
erator suddenly, the gearbox will not
change to a higher gear for reasons
of safety.
Manual operation
Manual changing of the four gears:
select position M in the gate,
push the lever to the + sign to
change to a higher gear,
pull the lever to the - sign to
change to a lower gear.
You can change from position D
(driving in automatic mode) to posi-
tion M (driving in manual mode) at
any time.
WARNING
Never select position N when the ve-
hicle is moving.
Never select positions P or R unless
the vehicle is stationary.
Never change between positions to
optimise braking on a slippery sur-
face.
Notes
For immediate maximum accelera-
tion without touching the gear lever,
press the accelerator pedal down as
far as it will go (kickdown). The gear-
box will automatically change down
or maintain the gear selected until
maximum engine speed is reached.
When the brake is applied, the gear-
box will automatically change down
i n o r d e r t o p r o v i d e e f fi c i e n t e n g i n e
braking. Sport and snow programmes
In addition to the auto-adaptive
programme, there are two special
programmes.
The programme is displayed on the
instrument panel screen.
Sport programme
Press button S once the engine
has been started.
The gearbox automatically favours
sporty driving and more dynamic ac-
celeration.
Snow programme
This programme improves starting
and drive when traction is poor.
Press button once the engine
has been started.
The gearbox adapts to driving on
slippery roads.
Notes
It is only possible to change from one
gear to another if the vehicle speed
and engine speed permit. If they do
not, the vehicle will operate tempo-
rarily in automatic mode.
When the vehicle is stationary or
moving very slowly, the gearbox au-
tomatically selects gear M1 .
Programmes S (sport) and (snow)
do not operate in manual mode.
Note: you can return to the auto-
adaptive programme at any time.
Press button S or again to switch
off the programme you are in.
Page 72 of 103
DRIVING70 -
HANDBRAKE
Operating abnormality
Any operating abnormality is indi-
cated by an audible signal, accom-
panied by the message 'Automatic
gear fault' on the multi-function dis-
play, by a "-" a n d fl a s h i n g o f t h e
Sport and Snow warning lights on the
instrument panel display.
In this situation the gearbox oper-
ates in downgrade mode (locked in
3rd gear). You may feel a substan-
tial knock when changing from P to
R and from N to R (this will not cause
any damage to the gearbox).
Do not exceed 60 mph (100 km/h),
respecting local speed limits.
Consult a PEUGEOT dealer. Illumination of this warning light
and of the STOP warning light,
accompanied by an audible sig-
nal (while the vehicle is being
driven) and the message "hand-
brake on" on the multifunction display,
indicates that the handbrake is still on or
has not been properly released.
Releasing
Pull on the handle and press the but-
ton to release the handbrake.
I f t h e b a t t e r y i s fl a t a n d t h e
lever is in position P , it will
be impossible to change
to another position.
In particular, do not force
the lever or there is a risk the gear-
box may be damaged. When parking on a slope,
direct your wheels towards
the pavement and pull the
handbrake.
Applying
Pull the handbrake to immobilise
your vehicle.