2008 PEUGEOT 1007 service
[x] Cancel search: servicePage 15 of 189
1
18
PETROL MANUAL GEARBOX AND "2 TRONIC" GEARBOX INSTRUMENT PANELS
1. Trip distance recorder zero
reset and total/trip distance
recorder display button.
2. Emission control system
warning light.
3. Service warning light.
4. Anti-lock braking system (ABS)
warning light.
5. Electronic stability control
(ESP/ASR) warning light.
6. H a n d b r a k e , b r a k e fl u i d l e v e l
and electronic brake force
distribution warning light.
7. Maximum coolant temperature
warning light.
8. Engine oil pressure warning light.
9. Punctured wheel warning light.
10. Battery charge warning light.
11. Left direction indicator.
12. Fuel gauge.
13. Low fuel level warning light.
14. Central STOP warning light.
15. Speedometer.
16. Speed limiter/cruise control
indicator light.
17. Service indicator, engine oil
level gauge and total/trip
distance recorder.
18. "2 Tronic" gearbox indicator.
19. Foot on brake warning light
("2 Tronic" gearbox).
20. Rev counter.
21. Right direction indicator.
22. Dipped headlamps indicator light.
23. Main beam headlamps indicator
light.
24. Front fog lamps indicator light.
25. Rear fog lamp indicator light.
26. Door open warning light.
27. Seat belt not fastened warning
light.
28. Passenger air bag disarmed
warning light.
29. Front, steering column, side and
curtain air bags warning light.
30. Lighting rheostat button.
Page 16 of 189
1
19
DIESEL MANUAL GEARBOX INSTRUMENT PANEL
1. Trip distance recorder zero
reset and total/trip distance
recorder display button.
2. Emission control system
warning light.
3. Service warning light.
4. Anti-lock braking system (ABS)
warning light.
5. Electronic stability control
(ESP/ASR) warning light.
6. H a n d b r a k e , b r a k e fl u i d l e v e l
and electronic brake force
distribution warning light.
7. Maximum coolant temperature
warning light.
8. Engine oil pressure warning light.
9. Punctured wheel warning light.
10. Battery charge warning light.
11. Left direction indicator.
12. Fuel gauge.
13. Low fuel level warning light.
14. Central STOP warning light.
15. Speedometer.
16. Diesel engine pre-heat warning
light.
17. W a t e r i n d i e s e l fi l t e r w a r n i n g
light.
18. Speed limiter/cruise control
indicator light.
19. Service indicator, engine oil
level gauge and total/trip
distance recorder.
20. Rev counter.
21. Right direction indicator.
22. Dipped headlamps indicator light.
23. Main beam headlamps indicator
light.
24. Front fog lamps indicator light.
25. Rear fog lamp indicator light.
26. Door open warning light.
27. Seat belt not fastened warning
light.
28. Passenger air bag disarmed
warning light.
29. Front, steering column, side and
curtain air bags warning light.
30. Lighting rheostat button.
Page 20 of 189
1
23
L a c k o f o i l
If "OIL" fl a s h e s a n d t h e s e r v i c e
warning light comes on, accompanied
by an audible signal and a message
on the multifunction display, this
indicates a lack of oil which could
damage the engine.
I f t h e l a c k o f o i l i s c o n fi r m e d b y a
check using the dipstick, it is essential
that the level is topped up.
E n g i n e o i l l e v e l i n d i c a t o r
When the ignition is switched on,
the engine oil level is indicated for
approximately 5 seconds after the
service indicator display.
O i l l e v e l g a u g e f a u l t
Check the oil level using the dip-
stick.
If " O I L - - " fl a s h e s , t h i s i n d i c a t e s a
malfunction of the engine oil level
gauge.
Consult a PEUGEOT dealer.
INSTRUMENT PANEL DISPLAY
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator
- total distance recorder (total and trip distances).
The level read on the dipstick
will only be correct if the ve-
hicle is on level ground and
the engine has been off for
more than 15 minutes.
O i l l e v e l c o r r e c t
N o t e : the trip distance is displayed
for thirty seconds, when the ignition
is switched off, on opening and
closing the driver’s door as well as
on locking the vehicle.
It also displays the "2 Tronic" gear-
box positions and operating modes
selected, as well as the information
relating to the cruise control or speed
limiter when one of these functions is
active.
Page 21 of 189
1
24
S e r v i c e i n d i c a t o r
This indicates when the next service
is due in accordance with the manu-
facturer’s servicing schedule.
The point at which the next service
is due is calculated from the last
indicator zero reset. It is determined
by two parameters:
- the distance travelled,
- the time which has elapsed since the last service.
Operation
When the ignition is switched on, the
spanner symbolising the servicing
operations comes on; the distance
recorder display indicates the number
of miles [kilometres] (rounded off)
remaining until the next service.
E x a m p l e : 4,800 miles/km remain be-
f o r e t h e n e x t s e r v i c e . F o r fi v e s e c o n d s
after the ignition is switched on, the
display indicates: 10 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the display indicates the total or trip
distance.
10 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and the
spanner remains lit.
It indicates that a service must be
carried out soon. The display indi-
cates the total or trip distance. T h e s e r v i c e i s o v e r d u e .
T h e s p a n n e r fl a s h e s f o r 5 s e c o n d s
each time the ignition is switched on.
10 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and the
spanner remains lit.
The display indicates the total or trip
distance.
The distance remaining before the
next service may be weighted by the
time factor, depending on the user’s
driving habits.
The spanner may also come on if
more than two years have elapsed
since the last service.
T h e d i s t a n c e r e m a i n i n g t o
t h e n e x t s e r v i c e i s l e s s t h a n
5 0 0 m i l e s / 1 , 0 0 0 k m .
E x a m p l e : 400 miles/900 km remain
before the next service.
For 5 seconds after the ignition is
switched on, the display indicates:
E x a m p l e : the service is overdue by
300 miles/km, your vehicle must be
serviced as soon as possible.
For 5 seconds after the ignition is
switched on, the display indicates:
Page 22 of 189
1
25
S e r v i c e i n d i c a t o r z e r o r e - s e t
Your PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
Switch off the ignition,
Press and hold the trip recorder
re-set button,
Switch on the ignition.
The display begins a countdown.
When the display shows "=0" , release
the button; the spanner disappears. T o t a l / t r i p d i s t a n c e r e c o r d e r
B r i e fl y p r e s s i n g t h e b u t t o n a l t e r n a t e s
between the total and trip distance
displays.
To reset the trip distance recorder to
zero, when it is displayed press the
button until zeros appear.
L i g h t i n g r h e o s t a t
With the lights on, press the button to
vary the intensity of the lighting of the
instruments and controls. When the
lighting reaches the required bright-
ness, release the button.
After this operation, if you
wish to disconnect the bat-
tery, lock the vehicle and
w a i t f o r a t l e a s t fi v e m i n u t e s ,
otherwise the zero re-set will not be
registered.
Page 52 of 189
3
55
Never drive with the head
restraints removed, they
must be in place and correctly
adjusted.
Locked Released
In order to ensure that the
seat covers have a long
service life, do not leave
the seat in the table or "fully
folded" position after loading.
Avoid placing luggage on the seats
when they are in the table position.
REAR HEAD RESTRAINTS
The rear head restraints can be
r e m o v e d a n d h a v e t w o p o s i t i o n s ;
- high, position for use
- low, storage position
Repositioning the seat
Press the control D upwards to check
that the rear feet are released.
Tilt the folded seat rearwards.
The rear feet are secured automatically.
Check that the seat is secured
correctly.
R a i s e t h e s e a t b a c k , r e l e a s i n g i t fi r s t
by pulling the control C . To raise a head restraint, pull it
upwards.
To lower it, press the lug then the
head restraint.
To remove it, place it in the high
position, push the lug and pull it
upwards.
T o r e fi t i t , e n g a g e t h e h e a d r e s t r a i n t
rods in the holes taking care to remain
in the centreline of the seat back.
Page 71 of 189
4
74
ELECTRONIC ENGINE IMMOBILISER
This locks the engine control system
a few moments after the ignition has
b e e n s w i t c h e d o f f a n d t h e r e f o r e p r e -
v e n t s s t a r t i n g o f t h e v e h i c l e b y a n y -
one who does not have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code is
recognised and starting is possible.
If the system does not function
correctly, the service warning light
comes on, accompanied by an
audible signal and a message on the
multifunction display.
In this case, your vehicle will not
start. Contact a PEUGEOT dealer as
soon as possible.
Lost keys
Visit a PEUGEOT dealer with the
v e h i c l e ’ s V 5 r e g i s t r a t i o n c e r t i fi c a t e
a n d y o u r p e r s o n a l i d e n t i fi c a t i o n d o c u -
ments.
A PEUGEOT dealer will be able to
r e t r i e v e t h e k e y c o d e a n d t h e t r a n s -
ponder code required to order a
replacement key.
Programming the remote
control
Following changing of the remote
control battery or disconnection of
the vehicle battery, the remote control
must be reprogrammed.
Wait at least one minute before
using the remote control.
Switch on the ignition.
Press button B or C for at least
fi v e s e c o n d s w i t h i n t h e n e x t t e n
seconds.
Switch off the ignition.
Wait at least one minute before
using the remote control.
The remote control is now working
again.
Changing the remote control
battery
Battery ref.: CR1620/3 volts.
T h e i n f o r m a t i o n " b a t t e r y fl a t " i s g i v e n
by displaying of the service warning
light, accompanied by an audible
s i g n a l a n d a m e s s a g e o n t h e m u l t i -
function display.
To replace the battery, unclip the
casing using a coin at the notch.
If the remote control does not work
after the battery has been changed,
r e - p r o g r a m m e t h e r e m o t e c o n t r o l .
Page 73 of 189
4
74
ELECTRONIC ENGINE IMMOBILISER
This locks the engine control system
a few moments after the ignition has
b e e n s w i t c h e d o f f a n d t h e r e f o r e p r e -
v e n t s s t a r t i n g o f t h e v e h i c l e b y a n y -
one who does not have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code is
recognised and starting is possible.
If the system does not function
correctly, the service warning light
comes on, accompanied by an
audible signal and a message on the
multifunction display.
In this case, your vehicle will not
start. Contact a PEUGEOT dealer as
soon as possible.
Lost keys
Visit a PEUGEOT dealer with the
v e h i c l e ’ s V 5 r e g i s t r a t i o n c e r t i fi c a t e
a n d y o u r p e r s o n a l i d e n t i fi c a t i o n d o c u -
ments.
A PEUGEOT dealer will be able to
r e t r i e v e t h e k e y c o d e a n d t h e t r a n s -
ponder code required to order a
replacement key.
Programming the remote
control
Following changing of the remote
control battery or disconnection of
the vehicle battery, the remote control
must be reprogrammed.
Wait at least one minute before
using the remote control.
Switch on the ignition.
Press button B or C for at least
fi v e s e c o n d s w i t h i n t h e n e x t t e n
seconds.
Switch off the ignition.
Wait at least one minute before
using the remote control.
The remote control is now working
again.
Changing the remote control
battery
Battery ref.: CR1620/3 volts.
T h e i n f o r m a t i o n " b a t t e r y fl a t " i s g i v e n
by displaying of the service warning
light, accompanied by an audible
s i g n a l a n d a m e s s a g e o n t h e m u l t i -
function display.
To replace the battery, unclip the
casing using a coin at the notch.
If the remote control does not work
after the battery has been changed,
r e - p r o g r a m m e t h e r e m o t e c o n t r o l .