2008 PEUGEOT 1007 service
[x] Cancel search: servicePage 79 of 189
4
80
Automatic central locking
The doors can lock automatically
when you are driving (at a speed of
more than 6 mph (10 km/h).
You can activate or deactivate this
function. Driving with the doors locked
may make access to the
passenger compartment by
the emergency services more
d i f fi c u l t i n a n e m e r g e n c y .
Activation
With the ignition on, press and hold
button A .
A c t i v a t i o n o f t h e f u n c t i o n i s a c c o m -
panied by an audible signal and a
message on the multifunction display.
Deactivation
With the ignition on, press and hold
button A .
Deactivation of the function is
accompanied by an audible signal
and a message on the multifunction
display.
"Door open" alert -
when the vehicle is moving,
by lighting of the "door open"
warning light, accompanied by
an audible signal and a message
on the multifunction display for a
few seconds.
Opening/Closing using the
remote control
Press button C or D to open or close
the left or right door.
The opening and closing of the
door is accompanied by an audible
signal.
2nd press on button C or D during
opening/closing interruption of the
movement.
3rd press on button C or D m o v e -
ment of the door in the opposite
direction.
You are advised to use the
r e m o t e c o n t r o l o r t h e c o n -
trols as much as possible.
Opening/Closing from the front
Press switch
B to open or close the
corresponding door.
Choosing the movement of the door
using the controls:
- p u l l opens the door,
- p u s h closes,
- s e c o n d p r e s s stops the
movement,
- t h e c o n t r o l s d o n o t f u n c t i o n above 3 mph (5 km/h).
If a door or the boot is not
closed properly, you are
warned:
- when the engine is running,
by lighting of the "door open"
warning light, accompanied by
a message on the multifunction
display for a few seconds.
Page 88 of 189
5
88
Daytime lights *
On vehicles which are equipped with
daytime lights, the dipped headlamps
come on when the vehicle is started.
A u t o m a t i c s w i t c h i n g o n o f
lights
The side lights and dipped beam
headlamps switch on automatically if
the light is poor and when the wind-
screen wipers operate continuously.
They switch off when the light be-
comes bright enough or the wind-
screen wipers are switched off.
I n f o g g y w e a t h e r o r i n
s n o w , t h e b r i g h t n e s s
s e n s o r c a n d e t e c t s u f fi -
c i e n t l i g h t , t h e l i g h t s w i l l
n o t c o m e o n a u t o m a t i -
cally.
D o n o t c o v e r t h e b r i g h t n e s s s e n -
s o r , c o u p l e d w i t h t h e r a i n s e n s o r ,
l o c a t e d i n t h e c e n t r e o f t h e w i n d -
screen behind the interior mirror.
I t i s u s e d f o r a u t o m a t i c s w i t c h i n g
on of the lights.
C o u p l i n g w i t h t h e F o l l o w M e
Home lighting
The association with the automatic
lighting function provides the follow
me home lighting with the following
additional options:
- selection of maintaining of the lighting for a duration of 15, 30
or 60 seconds in the vehicle pa-
rameters of the multifunction dis-
p l a y c o n fi g u r a t i o n m e n u ( e x c e p t
in the case of the monochrome
display A for which the duration
is pre-set),
- automatic activation of the fol- low me home lighting when the
automatic lighting function is in
operation.
Activation
Turn the lighting control to the
"
AUTO " position.
Disarming
Turn the lighting control to a position
other than " AUTO ".
Operating fault
If the brightness sensor does not
function correctly, the lights come on
accompanied by the service warning
light, an audible signal and a mes-
sage on the multifunction display.
Consult a PEUGEOT dealer. Operating fault
If the brightness sensor does not
function correctly, the lights come on
accompanied by the service warning
light, an audible signal and a mes-
sage on the multifunction display.
Contact a PEUGEOT dealer.
Do not cover the brightness
sensor, coupled with the rain
sensor, located in the centre
of the windscreen behind
the interior mirror; the as-
sociated functions would no
longer be controlled.
This warning light comes on
on the instrument panel.
The instruments and controls (instru-
ment panel, multifunction display,
air conditioning control panel, ...)
are only lit on switching to the auto-
matic switching on of the lights mode
or when the lights are switched on
manually.
* According to country.
Page 89 of 189
5
88
Daytime lights *
On vehicles which are equipped with
daytime lights, the dipped headlamps
come on when the vehicle is started.
A u t o m a t i c s w i t c h i n g o n o f
lights
The side lights and dipped beam
headlamps switch on automatically if
the light is poor and when the wind-
screen wipers operate continuously.
They switch off when the light be-
comes bright enough or the wind-
screen wipers are switched off.
I n f o g g y w e a t h e r o r i n
s n o w , t h e b r i g h t n e s s
s e n s o r c a n d e t e c t s u f fi -
c i e n t l i g h t , t h e l i g h t s w i l l
n o t c o m e o n a u t o m a t i -
cally.
D o n o t c o v e r t h e b r i g h t n e s s s e n -
s o r , c o u p l e d w i t h t h e r a i n s e n s o r ,
l o c a t e d i n t h e c e n t r e o f t h e w i n d -
screen behind the interior mirror.
I t i s u s e d f o r a u t o m a t i c s w i t c h i n g
on of the lights.
C o u p l i n g w i t h t h e F o l l o w M e
Home lighting
The association with the automatic
lighting function provides the follow
me home lighting with the following
additional options:
- selection of maintaining of the lighting for a duration of 15, 30
or 60 seconds in the vehicle pa-
rameters of the multifunction dis-
p l a y c o n fi g u r a t i o n m e n u ( e x c e p t
in the case of the monochrome
display A for which the duration
is pre-set),
- automatic activation of the fol- low me home lighting when the
automatic lighting function is in
operation.
Activation
Turn the lighting control to the
"
AUTO " position.
Disarming
Turn the lighting control to a position
other than " AUTO ".
Operating fault
If the brightness sensor does not
function correctly, the lights come on
accompanied by the service warning
light, an audible signal and a mes-
sage on the multifunction display.
Consult a PEUGEOT dealer. Operating fault
If the brightness sensor does not
function correctly, the lights come on
accompanied by the service warning
light, an audible signal and a mes-
sage on the multifunction display.
Contact a PEUGEOT dealer.
Do not cover the brightness
sensor, coupled with the rain
sensor, located in the centre
of the windscreen behind
the interior mirror; the as-
sociated functions would no
longer be controlled.
This warning light comes on
on the instrument panel.
The instruments and controls (instru-
ment panel, multifunction display,
air conditioning control panel, ...)
are only lit on switching to the auto-
matic switching on of the lights mode
or when the lights are switched on
manually.
* According to country.
Page 111 of 189
7
104
Switching to automated mode Reinitialisation
Following disconnection of the battery,
the gearbox must be reinitialised: The brake pedal must be
pressed while starting the
engine.
Never select neutral
N while
the vehicle is moving.
Only engage reverse gear R with the
vehicle immobilised and the brake
pedal pressed.
In all cases, it is imperative that you
apply the handbrake in order to im-
mobilise the vehicle.
On a steep gradient, it is preferable
to switch to sequential mode.
"Auto sequential" mode
In the automated mode, you can re-
sume control temporarily at any time
using the steering wheel controls.
The use of these controls permits
manual selection of the gears in situa-
tions which require a faster change-
down than that offered in automated
m o d e ( a r r i v a l a t a r o u n d a b o u t , e x i t
from a car park with a steep gradient,
overtaking...).
The gearbox engages the gear
requested if the engine speed
permits it.
"AUTO" is still displayed
on the instrument panel.
After a few moments, the gearbox
again controls the gears automatically.
Stopping the vehicle
Before switching off the engine, you
can:
- move to position N to leave the
gearbox in neutral.
- leave a gear engaged, such as fi r s t o r r e v e r s e .
In both cases, it is imperative that you
apply the handbrake to immobilise
the vehicle. Operating anomaly
W i t h t h e i g n i t i o n o n , t h e fl a s h i n g o f
"AUTO" and lighting of the service
warning light, accompanied by an
audible signal and a message on the
multifunction display, indicate a gear-
box malfunction.
Contact a PEUGEOT dealer without
delay.
If you press the accelera-
tor pedal beyond the point
of resistance, the gearbox
selects the gear below to
permit sharper acceleration. - switch on the ignition,
"AUTO"
and "-" appear on the instrument
panel display,
- press the brake pedal,
- wait approximately 30 seconds until "N" or a gear appears on
the instrument panel display,
- release the brake pedal.
The gearbox is operational again.
Automated mode
After using the sequential mode, you
can return to the automated mode by
selecting position
A .
"AUTO" and the gear engaged ap-
pear on the instrument panel display.
The gearbox then operates in auto-
active mode, without any action on
the part of the driver.
It continuously selects the gear most
suited to the following parameters:
- driving style,
- road characteristics,
- vehicle load.
To optimise driving comfort and ob-
tain the most suitable gear, avoid
sharp variations in the pressure on
the accelerator pedal.
Page 117 of 189
7
110
If there is an operating fault,
when reverse gear is en-
gaged, the service warning
light comes on, accompa-
nied by an audible signal
( s h o r t b l e e p ) a n d a m e s s a g e
on the multifunction display.
In bad or wintry weather, ensure that
the sensors are not covered with
mud, frost or snow.
Deactivation
With the engine running, press but-
ton A to deactivate the system per-
manently. The indicator light on the
button comes on.
The system will be deactivated auto-
matically when towing a trailer or
w h e n a b i c y c l e c a r r i e r i s fi t t e d ( v e h i c l e
fi t t e d w i t h a t o w b a r o r b i c y c l e c a r r i e r
recommended by PEUGEOT ). Reactivation
Press button
A again to reactivate
the system. The indicator light on the
button is switched off.
Page 121 of 189
8
115
CHECKING THE LEVELS
There are two marks on
the dipstick:
A = maximum
N e v e r fi l l p a s t t h i s m a r k .
B = minimum
Dipstick
Oil change
According to the information given in
the servicing booklet. Changing the brake fluid
T h e b r a k e fl u i d m u s t b e
changed at the intervals stat-
ed, according to the manu-
facturer’s servicing schedule.
U s e fl u i d s r e c o m m e n d e d b y t h e
m a n u f a c t u r e r , w h i c h f u l fi l D O T 4
standards. Windscreen and headlamp
wash level
For best quality cleaning and
for your safety, we would ad-
vise that you use products
recommended by PEUGEOT .
When the level is low, this is indicated
by an audible signal and a message
on the multifunction display.
Viscosity selection
In all cases, the oil selected must
meet the manufacturer’s require-
ments.
Cooling system
U s e t h e fl u i d r e c o m m e n d e d b y t h e
manufacturer.
When the engine is warm, the tem-
perature of the coolant is controlled
by the engine fan. As this fan can ope-
rate with the ignition key removed
and because the cooling system is
pressurised, wait for at least one hour
after the engine has stopped before
carrying out any work.
Slacken the cap by two turns to re-
lease the pressure to prevent any
risk of scalding. When the pressure
has dropped, remove the cap and
top up the level. Diesel additive level (Diesel
with particle emission filter)
Lighting of the service warning light,
accompanied by a message and an
audible signal, indicates that the die-
sel additive level is low.
This additive must be topped up.
Contact a PEUGEOT dealer as soon
as possible.
To maintain the reliability of
engines and emission control
systems, the use of additives
in engine oil is prohibited. Used oil
Avoid prolonged contact of used oil
with the skin.
B r a k e fl u i d i s h a r m f u l t o h e a l t h a n d
very corrosive.
Note: the coolant does not need to
be changed.
The level must always be
above the MIN mark and
close to the MAX mark. Do not dispose of used oil,
b r a k e fl u i d o r c o o l a n t i n t o
drains or into the ground.
Oil level
Check the level regularly and
top up between changes. The
maximum consumption is 0.5 l
per 600 miles (1 000 km).
Check the level with the ve-
hicle level, engine cold, using the oil
level gauge on the instrument panel
or the dipstick.
Page 122 of 189
8
116
CHECKS
Handbrake Where the handbrake travel
is too great or there is a re-
duction in the performance
of the system, the hand-
brake should be adjusted,
even between services.
H a v e t h e s y s t e m c h e c k e d b y a
PEUGEOT dealer. Manual gearbox
This does not require an oil
c h a n g e . H a v e t h e l e v e l c h e c k e d
in accordance with the manu-
facturer’s servicing schedule. Air filter and passenger compartment filter
Particle emission filter (Diesel)
It is imperative that maintenance of
t h e p a r t i c l e e m i s s i o n fi l t e r i s c a r r i e d
out by a PEUGEOT dealer in accord-
ance with the manufacturer’s servicing
schedule. Brake pads
Brake pad wear depends
on the style of driving, in
particular for vehicles which
are used in town, over short
distances.
Brake disc/drum wear status
For any information relating to the
wear of the surfaces of the discs and
drums, contact a PEUGEOT dealer. Oil filter
C h a n g e t h e fi l t e r r e g u l a r -
ly, in accordance with the
servicing schedule.
It may be necessary to check
the thickness of the pads,
even between services.
Unless there is a leak in the circuit, a
d r o p i n t h e b r a k e fl u i d l e v e l i n d i c a t e s
that the brake pads are worn.
Only use products recom-
mended by PEUGEOT or
products of equivalent quali-
ty and characteristics.
To ensure best performance
from components as important as the
braking system, PEUGEOT selects
a n d o f f e r s q u i t e s p e c i fi c p r o d u c t s .
To prevent damage to the electrical
units, high pressure washing of the
engine compartment is strictly pro-
hibited .
At the start of winter, have
your battery checked by a
PEUGEOT dealer.
Refer to the servicing book-
let for information on the re-
placement interval for these
components.
Depending on the environment (dusty
atmosphere...) and the use of the ve-
hicle (urban driving...), change them
twice as often, if necessary (refer to
the "Engines" paragraph).
A c l o g g e d p a s s e n g e r c o m p a r t m e n t fi l -
ter may have an adverse effect on the
performance of the air conditioning sys-
tem and produce unpleasant odours.
To check the main levels
and certain components,
in accordance with the
manufacturer’s servic-
ing schedule, refer to the pages of
the servicing booklet which corre-
spond to your vehicle’s engine.
Following prolonged opera-
tion of the vehicle at very
low speed or at idle, you
may, in exceptional circum-
stances, notice steam coming from
the exhaust during acceleration. This
has no effect on the performance of
the vehicle or on the environment.
Battery
Page 146 of 189
S
O S SOU R CE
MODE B AND ESC
2
abc
5
jkl
8
tuv 3
def
6
mno
9
wxyz
1 4
ghi
7
pqr s
0 # MENU LIST
TA
P T Y
DARK
139
RT4
MULTIMEDIA AUDIO EQUIPMENT/TELEPHONE JUKEBOX FUNCTION (10 GB)/GPS (EUROPE)
The SERVICE BOX internet site provides additional
animated information about the RT4. It can be consu lted at
the following address:
http://public.servicebox.peugeot.com.
Simple registration permits access and free consul tation of
the handbook.
The RT4 GPS audio/telephone is coded in such a
way that it will only operate in your vehicle. If i t is to be
installed in another vehicle, contact a PEUGEOT d ealer
f o r c o n fi g u r a t i o n o f t h e s y s t e m .
For safety reasons, it is imperative that the driv er carries
out operations which require prolonged attention wh ile
the vehicle is stationary.
When the engine is switched off and to prevent
discharging of the battery, the RT4 audio/telephone may
switch off after a few minutes. CONTENTS