2008 PEUGEOT 1007 DAG light
[x] Cancel search: lightPage 109 of 194
7
102
When the vehicle is being
driven, illumination of this
warning light and of the STOP
warning light, accompanied
by an audible signal and a message
on the multifunction display, indicates
that the handbrake is still on or has
not been properly released.
When parking on a slope, di-
rect your wheels to immobilise
them against the pavement,
pull the handbrake and engage
a gear.
"2 TRONIC" GEARBOX
T h e fi v e - s p e e d c o n t r o l l e d m a n u a l
gearbox offers a choice between the
comfort of automatic regulation or the
pleasure of manual gear changing.
HANDBRAKE
Gear lever positions
N : neutral.
With your foot on the brake, select
this position to start.
R
: reverse gear.
With the vehicle stationary, keep your
foot on the brake pedal and push the
gear lever upwards.
Selection of reverse gear is accom-
panied by an audible signal.
A
: automated mode.
Move the lever downwards to select
this mode.
M +/-: sequential mode with manual
gear changing.
Applying
Pull the handbrake to immobilise
your vehicle.
It consists of the following controls:
- a gear lever 1 on the centre
console for selecting the driving
mode, reverse gear and neutral
or for changing gear in sequential
mode,
- a "-" steering wheel control 2
for sequential downward gear
changes,
- a "+" steering wheel control 3 for
sequential upward gear changes.
Releasing
Pull on the handle and press the
button to release the handbrake.
This gearbox enables you to access
two driving modes:
- an automated mode for automatic
control of the gears by the gear-
box and therefore without any
action on the part of the driver,
- a sequential mode for manual changing of the gears by the
driver using the steering wheel
controls or the gear lever.
Move the lever downwards, then to
the left to select this mode, then:
- push forward to change up,
- push rearward to change down.
Page 111 of 194
7
104
Switching to automated mode Reinitialisation
Following disconnection of the battery,
the gearbox must be reinitialised: The brake pedal must be
pressed while starting the
engine.
Never select neutral N while the vehi-
cle is moving.
Only engage reverse gear R with the
vehicle immobilised and the brake
pedal pressed.
In all cases, it is imperative that
you apply the handbrake in order to
immobilise the vehicle.
On a steep gradient, it is preferable
to switch to sequential mode.
"Auto sequential" mode
In the automated mode, you can
resume control temporarily at any
time using the steering wheel controls.
The use of these controls permits
manual selection of the gears in situ-
ations which require a faster change-
down than that offered in automated
m o d e ( a r r i v a l a t a r o u n d a b o u t , e x i t
from a car park with a steep gradient,
overtaking...).
The gearbox engages the gear re-
quested if the engine speed permits
it.
"AUTO" is still displayed on the
instrument panel.
After a few moments, the gearbox
again controls the gears automatically.
Stopping the vehicle
Before switching off the engine, you
can:
- move to position N to leave the
gearbox in neutral.
- leave a gear engaged, such as fi r s t o r r e v e r s e .
In both cases, it is imperative that
you apply the handbrake to immobi-
lise the vehicle. Operating anomaly
W i t h t h e i g n i t i o n o n , t h e fl a s h i n g o f
"AUTO" and lighting of the service
warning light, accompanied by an
audible signal and a message on the
multifunction display, indicate a gear-
box malfunction.
Contact a PEUGEOT dealer without
delay.
If you press the accelerator
pedal beyond the point of
resistance, the gearbox
selects the gear below to
permit sharper acceleration. - switch on the ignition,
"AUTO"
and "-" appear on the instrument
panel display,
- press the brake pedal,
- wait approximately 30 seconds until "N" or a gear appears on
the instrument panel display,
- release the brake pedal.
The gearbox is operational again.
Automated mode
After using the sequential mode, you
can return to the automated mode by
selecting position
A .
"AUTO" and the gear engaged appear
on the instrument panel display.
The gearbox then operates in auto-
active mode, without any action on
the part of the driver.
It continuously selects the gear most
suited to the following parameters:
- driving style,
- road characteristics,
- vehicle load.
To optimise driving comfort and
obtain the most suitable gear, avoid
sharp variations in the pressure on
the accelerator pedal.
Page 117 of 194
7
110
If there is an operating fault,
when reverse gear is enga-
ged, the service warning
light comes on, accompa-
nied by an audible signal
( s h o r t b l e e p ) a n d a m e s s a g e
on the multifunction display.
In bad or wintry weather, ensure that
the sensors are not covered with
mud, frost or snow.
Deactivation
With the engine running, press button A
to deactivate the system permanently.
The indicator light on the button comes
on.
The system will be deactivated
automatically when towing a trailer or
w h e n a b i c y c l e c a r r i e r i s fi t t e d ( v e h i c l e
fi t t e d w i t h a t o w b a r o r b i c y c l e c a r r i e r
recommended by PEUGEOT ).
Reactivation
Press button A again to reactivate
the system. The indicator light on the
button is switched off.
Page 121 of 194
8
115
CHECKING THE LEVELS
There are two marks on
the dipstick:
A = maximum
N e v e r fi l l p a s t t h i s m a r k .
B = minimum
Dipstick
Oil change
According to the information given in
the servicing booklet. Changing the brake fluid
T h e b r a k e fl u i d m u s t b e
changed at the intervals
stated, according to the
manufacturer's servicing
schedule.
U s e fl u i d s r e c o m m e n d e d b y t h e m a n -
u f a c t u r e r , w h i c h f u l fi l D O T 4 s t a n d a r d s . Windscreen and headlamp
wash level
For best quality cleaning and
for your safety, we would ad-
vise that you use products
recommended by PEUGEOT .
When the level is low, this is indicated
by an audible signal and a message
on the multifunction display.
Viscosity selection
In all cases, the oil selected must
meet the manufacturer's require-
ments.
Cooling system
U s e t h e fl u i d r e c o m m e n d e d b y t h e
manufacturer.
When the engine is warm, the tem-
perature of the coolant is controlled
by the engine fan. As this fan can ope
rate with the ignition key removed and
because the cooling system is pres-
surised, wait for at least one hour after
the engine has stopped before carry-
ing out any work.
Slacken the cap by two turns to re-
lease the pressure to prevent any
risk of scalding. When the pressure
has dropped, remove the cap and
top up the level. Diesel additive level (Diesel
with particle emission filter)
Lighting of the service warning light,
accompanied by a message and an
audible signal, indicates that the die-
sel additive level is low.
This additive must be topped up.
Contact a PEUGEOT dealer as soon
as possible.
To maintain the reliability of
engines and emission control
systems, the use of additives
in engine oil is prohibited. Used oil
Avoid prolonged contact of used oil
with the skin.
B r a k e fl u i d i s h a r m f u l t o h e a l t h a n d
very corrosive.
Note
: the coolant does not need to
be changed.
The level must always be
above the MIN mark and
close to the MAX mark. Do not dispose of used oil,
b r a k e fl u i d o r c o o l a n t i n t o
drains or into the ground.
Oil level
Check the level regularly
and top up between chang-
es. The maximum consump-
tion is 0.5 l per 600 miles
(1 000 km).
Check the level with the vehicle level,
engine cold, using the oil level gauge
on the instrument panel or the dip-
stick.
Page 124 of 194
9
118
Removing a wheel
- Place the chock 2 (integrated
with the box) at the rear of the
wheel diagonally opposite the
wheel to be changed.
- Remove the wheel trim, using the wheelbrace 3 , by pulling at
the valve passage hole.
- Remove the chrome-plated bolt covers and the plastic cover from
the bolts using the "bolt cover" tool 5
(Special features of alloy wheels).
- Slacken the wheel bolts.
- Place the jack 1 under one of the
four locating points A on the sub-
frame closest to the wheel to be
changed. Ensure that the entire
surface of the jack base plate is
in contact with the ground.
-
Extend the jack, completely unscrew
the bolts and remove the wheel.
Refitting the wheel
- Position the wheel on the hub.
- Lightly pre-tighten the bolts us- ing the wheelbrace 3 .
-
Compress the jack 1 and release it.
- Fully tighten the bolts using the wheelbrace.
- Replace the trim, starting at the valve passage hole, and press it
on using the palm of the hand.
For your safety, always
change a wheel:
- Stow the tools in the case, then
put it back in the left boot trim.
T h e j a c k a n d t h e t o o l k i t a r e s p e c i fi c
to your vehicle. Do not use them for
other purposes.
Replacing the wheel in the
carrier
- Replace the jack 1 in the box.
- Replace the box in the wheel.
- Replace the wheel in the carrier.
- Lift the wheel then the carrier and reposition the hook.
- Do not forget to fully tighten the spare wheel carrier retaining bolt. After changing the wheel
- Have the tightening of the bolts
and the pressure of the spare
tyre checked as soon as possi-
ble by a PEUGEOT dealer.
- Do not exceed its maximum au- thorised speed: 50 mph (80 km/h).
- Have the punctured tyre repaired and replace it on the vehicle as
soon as possible.
- 15 and 16 inch punctured wheels cannot be placed in the carrier.
- on level, stable and non-slippery
ground,
- with the handbrake applied,
- w i t h fi r s t o r r e v e r s e g e a r e n g a g e d (position R for the "2 Tronic" gear-
box),
- with the vehicle chocked,
- never go underneath a vehicle raised using a jack (use an axle
stand).
Page 126 of 194
9
120
CHANGING A BULB 2 - Dipped beam headlamps/Main beam headlamps
(H4 - 60/55 W)
- Remove the plastic cover B .
- Disconnect the connector.
- Push the spring D towards the
right, as indicated on the head-
lamp.
- Remove and replace the bulb. 3 - Direction indicators
(PY 21 W amber)
- Turn the bulb holder C a quarter
of a turn and remove it.
- Turn the bulb a quarter of a turn.
- Remove the bulb and change it.
In certain weather conditions
(low temperatures, humidity),
the presence of condensa-
tion on the inside of the
headlamp glass is normal ; it disap-
pears a few minutes after the lights
have been switched on.
Front lights
1 - Side lights (W 5 W)
- Remove the plastic cover A .
- Remove the bulb holder.
- Remove the bulb and change it.
Page 128 of 194
9
122
Rear lights
1. Brake/side lights
(P21 W/5 W).
2. Direction indicators (P21 W).
3. Reversing light (P21 W), right
side.
Fog lamp (P21 W), left side.
These 4 bulbs are changed by re-
moving the light:
R e m o v e t h e a c c e s s fl a p i n t h e
corresponding boot side trim to
access the light,
R e m o v e t h e t w o l i g h t fi x i n g n u t s
inside the boot,
Unclip the harness,
Remove the light pressing on the
retaining tabs,
Remove the seal,
Remove the bulb holder moving
aside the two tabs A ,
Turn the bulb a quarter of a turn,
Remove the bulb and change it.
Note: if necessary, use the wheel-
brace to remove the nuts.
W h e n r e fi t t i n g , p r o c e e d i n t h e r e -
verse order and take care to position
the bulb holder, the seal and the light
correctly. Third brake light
(4 W 5 W bulbs)
Using a 10 mm box spanner, un-
s c r e w t h e 2 fi x i n g n u t s A .
Release the lamp unit by push-
ing it outwards.
Disconnect the connector and
the rear wash-wipe pipe.
Turn the bulb holder a quarter of
a turn and remove it.
Remove the bulb and change it.
W h e n r e fi t t i n g , p r o c e e d i n t h e r e -
verse order and ensure that the lamp
unit seal and the rear wash-wipe pipe
have been put back in place correctly.
Do not tighten the nuts more than is
necessary at the risk of breaking the
light.
Number plate lights (W 5 W)
Insert a thin screwdriver into one
of the external holes of the lens.
Push it outwards to unclip it.
Remove the lens.
Remove the bulb and change it.
Page 131 of 194
9
124
Fuse N°RatingFunctions
115 ARear wiper.
35 AAir bags and pre-tensioners control unit.
410 ADiagnostic socket - Clutch switch - Steering wheel angle sensor - P a r t i c l e e m i s s i o n fi l t e r p u m p .
530 AElectric windows - Sunroof.
6-Not used.
75 ACourtesy light - Glove box lighting.
820 A T y r e u n d e r - i n fl a t i o n d e t e c t i o n c o n t r o l u n i t - E l e c t r i c m i r r o r f o l d i n g - A l a r m s i r e n - Multifunction display - Alarm control unit - Audio equipment - Aud io/telephone.
930 AAudio equipment - Lighter/12 V socket (100 W max).
1015 ASteering wheel controls.
1115 ADiagnostic socket - Low current ignition switch - Motorised strikers.
1215 AAir bags and pre-tensioners control unit - Rain/brightness sensor.
135 AABS relay - Speed sensor - Engine Fuse Box - "2 Tronic" gear lever - Brake swit ch.
1415 AParking assistance control unit - "Sesame" doors control unit and switches - Instrument panel - Seat belt warning lights bar - Air conditioning control panel - Headlamp adjustment - Hands-free kit.
1530 ALocking - Deadlocking - Unlocking.
1740 ARear screen and exterior mirrors demisting.
SH-PARC shunt.