2008 PEUGEOT 1007 DAG wheel
[x] Cancel search: wheelPage 110 of 194
7
103
Functions of the steering
wheel controls
+
:
manual gear changing in sequential
mode.
Press behind the "+" steering wheel
control to change up.
-
:
manual gear changing in sequential
mode.
Press behind the "-" steering wheel
control to change down. Stopping - Starting on a slope
The "2 Tronic" gearbox is a controlled
manual gearbox which does not have
a clutch pedal.
Do not use the accelerator pedal to
immobilise the vehicle on a slope,
apply the handbrake instead.
When starting on a slope, accelerate
gradually while releasing the hand-
brake.
Moving off
Select position N . Switching to sequential mode
Once you have moved off, you can
switch to sequential mode by select-
ing position
M .
"AUTO" disappears and the gears
engaged appear in succession on
the instrument panel display.
The gear change requests are only
carried out if the engine speed
permits it.
Take your foot off the accelerator
pedal gently to engage the gear.
At low speeds, when approaching a
s t o p o r t r a f fi c l i g h t s f o r e x a m p l e , t h e
g e a r b o x c h a n g e s d o w n t o fi r s t g e a r
automatically.
P r e s s t h e b r a k e p e d a l fi r m l y
while starting the engine.
Start the engine. "N" appears on the
instrument panel display.
S e l e c t fi r s t g e a r ( p o s i t i o n M or A ) or
r e v e r s e ( p o s i t i o n R ).
Release the handbrake.
Release the brake pedal then acce-
lerate.
"AUTO" and "1" or "R" appear on
the instrument panel display.
It is possible to start in 2nd gear
using the gear lever, in sequential
mode only.
Page 111 of 194
7
104
Switching to automated mode Reinitialisation
Following disconnection of the battery,
the gearbox must be reinitialised: The brake pedal must be
pressed while starting the
engine.
Never select neutral N while the vehi-
cle is moving.
Only engage reverse gear R with the
vehicle immobilised and the brake
pedal pressed.
In all cases, it is imperative that
you apply the handbrake in order to
immobilise the vehicle.
On a steep gradient, it is preferable
to switch to sequential mode.
"Auto sequential" mode
In the automated mode, you can
resume control temporarily at any
time using the steering wheel controls.
The use of these controls permits
manual selection of the gears in situ-
ations which require a faster change-
down than that offered in automated
m o d e ( a r r i v a l a t a r o u n d a b o u t , e x i t
from a car park with a steep gradient,
overtaking...).
The gearbox engages the gear re-
quested if the engine speed permits
it.
"AUTO" is still displayed on the
instrument panel.
After a few moments, the gearbox
again controls the gears automatically.
Stopping the vehicle
Before switching off the engine, you
can:
- move to position N to leave the
gearbox in neutral.
- leave a gear engaged, such as fi r s t o r r e v e r s e .
In both cases, it is imperative that
you apply the handbrake to immobi-
lise the vehicle. Operating anomaly
W i t h t h e i g n i t i o n o n , t h e fl a s h i n g o f
"AUTO" and lighting of the service
warning light, accompanied by an
audible signal and a message on the
multifunction display, indicate a gear-
box malfunction.
Contact a PEUGEOT dealer without
delay.
If you press the accelerator
pedal beyond the point of
resistance, the gearbox
selects the gear below to
permit sharper acceleration. - switch on the ignition,
"AUTO"
and "-" appear on the instrument
panel display,
- press the brake pedal,
- wait approximately 30 seconds until "N" or a gear appears on
the instrument panel display,
- release the brake pedal.
The gearbox is operational again.
Automated mode
After using the sequential mode, you
can return to the automated mode by
selecting position
A .
"AUTO" and the gear engaged appear
on the instrument panel display.
The gearbox then operates in auto-
active mode, without any action on
the part of the driver.
It continuously selects the gear most
suited to the following parameters:
- driving style,
- road characteristics,
- vehicle load.
To optimise driving comfort and
obtain the most suitable gear, avoid
sharp variations in the pressure on
the accelerator pedal.
Page 112 of 194
7
105
Steering wheel controls
This system's controls are grouped
together on lever A .
1. Speed limiter mode selection dial
2. Value decrease button
3. Value increase button
4. Speed limiter on/off button Instrument panel display
The programmed information is
grouped together on the instrument
panel display.
5. Speed limiter on/off indication
6. Speed limiter mode selection in-
dication
7. Programmed speed value
SPEED LIMITER
This speed limiter, of the new genera-
tion, has a display on the instrument
panel to indicate the programmed
speed.
It prevents exceeding of the vehicle
speed programmed by the driver.
When the programmed speed is
reached, pressing the accelerator
pedal no longer has any effect.
The limiter operates with a pro-
grammed speed of at least 18 mph
( 3 0 k m / h ) ; i t r e m a i n s a c t i v e r e g a r d -
less of any action on the brake and
clutch pedals.
The speed limiter is switched on
manually: it requires a programmed
s p e e d o f a t l e a s t 1 8 m p h ( 3 0 k m / h ) .
The speed limiter is switched off by
manual operation of the control.
By pressing the accelerator pedal
fi r m l y , p a s s i n g t h e p o i n t o f r e s i s -
tance, it is possible to exceed the
programmed speed temporarily.
To return to the programmed speed,
simply slow down to a speed below
the programmed speed.
The programmed speed value remains
in the memory when the ignition is
switched off.
Page 114 of 194
7
1 0 7
CRUISE CONTROL
This cruise control, of the new genera-
tion, is linked with the speed limiter. It
has a display on the instrument panel
to indicate the memorised reference
speed.
It enables the vehicle to maintain a
steady speed programmed by the
driver.
The cruise control is switched on
manually: it requires a minimum ve-
h i c l e s p e e d o f 2 5 m p h ( 4 0 k m / h ) a n d
fourth gear must be engaged on the
manual gearbox.
The cruise control is switched off
by means of a manual action or by
pressing the brake or clutch pedal or
in the event of activation of the ESP.
By pressing the accelerator pedal, it is
possible to exceed the programmed
speed temporarily.
To return to the programmed speed,
simply release the accelerator pedal.
Switching off the ignition or turning
the dial cancels any programmed
speed value. Instrument panel display
The programmed information is
grouped together on the instrument
panel display.
5. Cruise control on/off indication
6. Cruise control mode selection in-
dication
7. Programmed speed value
Steering wheel controls
This system's controls are grouped
together on lever
A .
1. Cruise control mode selection dial
2. Value decrease button
3. Value increase button
4. Cruise control on/off button
Page 123 of 194
9
117
Parking the vehicle
- If possible, park the vehicle on level, stable and non-slippery
ground.
- It is imperative that you ensure that the occupants get out of the vehi-
cle and wait in a safe location.
- Apply the handbrake, switch off t h e i g n i t i o n a n d e n g a g e fi r s t o r
reverse gear (position R for the
"2 Tronic" gearbox).
CHANGING A WHEEL
1. Jack with integrated handle.
2. Chock.
3. Wheelbrace.
4. Extension.
5. "Bolt cover" tool.
6. Removable towing eye. Access to the spare wheel and
the jack
The wheel is located outside the ve-
h i c l e , u n d e r t h e r e a r fl o o r , s u p p o r t e d
by a metal carrier.
- Unclip the cover to gain access
to the spare wheel carrier retain-
ing bolt, located on the inside
near the closing system.
- Using the wheelbrace 3 and the
extension 4 , slacken the spare
wheel carrier retaining bolt.
- Lift the carrier to release the hook rearwards, then lower it.
- Remove the spare wheel and the box.
- Remove the jack 1 from the box.
Tools provided
The jack is stored in a box in the cen-
tre of the spare wheel. The chock is
fi x e d o n t h e s i d e o f t h e b o x .
The other tools are stored in a case
in the left boot trim.
Note: i f y o u r v e h i c l e i s fi t t e d w i t h a
towbar, the case is stored in the left
s t o r a g e t r a y ( l o c a t e d i n t h e fl o o r o f
the rear footwell).
Page 124 of 194
9
118
Removing a wheel
- Place the chock 2 (integrated
with the box) at the rear of the
wheel diagonally opposite the
wheel to be changed.
- Remove the wheel trim, using the wheelbrace 3 , by pulling at
the valve passage hole.
- Remove the chrome-plated bolt covers and the plastic cover from
the bolts using the "bolt cover" tool 5
(Special features of alloy wheels).
- Slacken the wheel bolts.
- Place the jack 1 under one of the
four locating points A on the sub-
frame closest to the wheel to be
changed. Ensure that the entire
surface of the jack base plate is
in contact with the ground.
-
Extend the jack, completely unscrew
the bolts and remove the wheel.
Refitting the wheel
- Position the wheel on the hub.
- Lightly pre-tighten the bolts us- ing the wheelbrace 3 .
-
Compress the jack 1 and release it.
- Fully tighten the bolts using the wheelbrace.
- Replace the trim, starting at the valve passage hole, and press it
on using the palm of the hand.
For your safety, always
change a wheel:
- Stow the tools in the case, then
put it back in the left boot trim.
T h e j a c k a n d t h e t o o l k i t a r e s p e c i fi c
to your vehicle. Do not use them for
other purposes.
Replacing the wheel in the
carrier
- Replace the jack 1 in the box.
- Replace the box in the wheel.
- Replace the wheel in the carrier.
- Lift the wheel then the carrier and reposition the hook.
- Do not forget to fully tighten the spare wheel carrier retaining bolt. After changing the wheel
- Have the tightening of the bolts
and the pressure of the spare
tyre checked as soon as possi-
ble by a PEUGEOT dealer.
- Do not exceed its maximum au- thorised speed: 50 mph (80 km/h).
- Have the punctured tyre repaired and replace it on the vehicle as
soon as possible.
- 15 and 16 inch punctured wheels cannot be placed in the carrier.
- on level, stable and non-slippery
ground,
- with the handbrake applied,
- w i t h fi r s t o r r e v e r s e g e a r e n g a g e d (position R for the "2 Tronic" gear-
box),
- with the vehicle chocked,
- never go underneath a vehicle raised using a jack (use an axle
stand).
Page 125 of 194
9
119
Special features of alloy
wheels Fitting the spare wheel
I f y o u r v e h i c l e i s fi t t e d w i t h a s t e e l
s p a r e w h e e l , w h e n fi t t i n g i t , i t i s
nor-
mal when tightening the bolts to no-
tice that the washers do not come
into contact with the rim. The spare
wheel is secured by the cone shape
of each bolt. Anti-theft bolts
I f y o u r w h e e l s a r e fi t t e d w i t h a n a n t i -
theft bolt (one per wheel), the chrome
trim must be removed before un-
screwing the bolt using the anti-theft
socket and the wheelbrace.
Fitting snow tyres
I f y o u fi t s n o w t y r e s m o u n t e d o n s t e e l
wheels onto your vehicle, it is es-
sential to use special bolts available
from PEUGEOT dealers.
Wheels equipped with 195/50R16
t y r e s c a n n o t b e fi t t e d w i t h s n o w
chains.
For further information, contact a
PEUGEOT dealer.
Bolt covers
Alloy wheel bolts are covered by
chrome trims.
Use the yellow tool to remove the
trims before slackening the bolts.
Page 128 of 194
9
122
Rear lights
1. Brake/side lights
(P21 W/5 W).
2. Direction indicators (P21 W).
3. Reversing light (P21 W), right
side.
Fog lamp (P21 W), left side.
These 4 bulbs are changed by re-
moving the light:
R e m o v e t h e a c c e s s fl a p i n t h e
corresponding boot side trim to
access the light,
R e m o v e t h e t w o l i g h t fi x i n g n u t s
inside the boot,
Unclip the harness,
Remove the light pressing on the
retaining tabs,
Remove the seal,
Remove the bulb holder moving
aside the two tabs A ,
Turn the bulb a quarter of a turn,
Remove the bulb and change it.
Note: if necessary, use the wheel-
brace to remove the nuts.
W h e n r e fi t t i n g , p r o c e e d i n t h e r e -
verse order and take care to position
the bulb holder, the seal and the light
correctly. Third brake light
(4 W 5 W bulbs)
Using a 10 mm box spanner, un-
s c r e w t h e 2 fi x i n g n u t s A .
Release the lamp unit by push-
ing it outwards.
Disconnect the connector and
the rear wash-wipe pipe.
Turn the bulb holder a quarter of
a turn and remove it.
Remove the bulb and change it.
W h e n r e fi t t i n g , p r o c e e d i n t h e r e -
verse order and ensure that the lamp
unit seal and the rear wash-wipe pipe
have been put back in place correctly.
Do not tighten the nuts more than is
necessary at the risk of breaking the
light.
Number plate lights (W 5 W)
Insert a thin screwdriver into one
of the external holes of the lens.
Push it outwards to unclip it.
Remove the lens.
Remove the bulb and change it.