2008 NISSAN TEANA engine

FLUID COOLER SYSTEM
TM-167
< ON-VEHICLE REPAIR >[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
InspectionINFOID:0000000003849107
After completing installation, check for engine coolant leakage and check engine coolant level. Refer to CO-8,
"Inspection".

TM-168
< REMOVAL AND INSTALLATION >[CVT: RE0F09B]
TRANSAXLE ASSEMBLY
REMOVAL AND INSTALLATION
TRANSAXLE ASSEMBLY
Exploded ViewINFOID:0000000003849108
Removal and InstallationINFOID:0000000003849109
WARNING:
Never remove the reservoir tank cap when the engine is hot. Serious burns could occur from high
pressure engine coolant escaping from the reservoir tank.
REMOVAL
1. Remove the engine, the transaxle assembly and front suspension member. Refer to EM-67, "Exploded
View".
2. Lift with hoist and separate engine, transaxle assembly from front suspension member. Refer to EM-67,
"Exploded View".
1. CVT fluid level gauge 2. CVT fluid charging pipe 3. O-ring
4. Transaxle assembly
A. For tightening torque, refer to TM-168, "
Removal and Installation".
Refer to GI-4, "
Components" for symbols in the figure.
JPDIA0799GB

TRANSAXLE ASSEMBLY
TM-169
< REMOVAL AND INSTALLATION >[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
3. Remove air breather hose. Refer to TM-164, "Exploded View".
4. Disconnect secondary speed sensor connector. Refer to TM-161, "
Exploded View".
5. Disconnect CVT unit connector.
6. Disconnect air fuel ratio sensor 1 (bank 2). Refer to EM-34, "
Exploded View".
7. Remove crankshaft position sensor (POS). Refer to EM-38, "
Exploded View".
8. Remove CVT fluid charging pipe from transaxle assembly.
9. Remove transaxle assembly fixing bolts with power tool.
10. Remove transaxle assembly from engine assembly with a hoist.
11. Remove fluid cooler hose from transaxle assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Check fitting of dowel pins ( ) when installing transaxle
assembly to engine assembly.
When installing transaxle assembly to the engine assembly, attach
the fixing bolts in accordance with the following.
JPDIA0598ZZ
JPDIA0602ZZ
JPDIA0600ZZ
Insertion direction Transaxle assembly to engine assemblyEngine assembly to tran-
saxle assembly
Bolt position A B C D
Number of bolts 1 2 2 4
Bolt length mm (in) 55 (2.17) 39 (1.54) 108 (4.25) 40 (1.57)
Tightening torque
N·m (kg-m, ft-lb)74.5 (7.6, 55) 50 (4.3, 31)

TM-170
< REMOVAL AND INSTALLATION >[CVT: RE0F09B]
TRANSAXLE ASSEMBLY
 When using the drive plate location guide (commercial service tool:
31197CA000) (A), set it to the stud bolts which is used to install it
to the torque converter.
 When not using drive plate location guide, rotate torque converter
so that the stud bolt (B) for mounting the drive plate location guide
of torque converter aligns with the mounting position of service
hole.
 Rotate crankshaft so that the hole (A) for inserting drive plate loca-
tion guide of drive plate aligns with the service hole (B).
NOTE:
When not using drive plate location guide, insert stud bolt of torque
converter into the hole (C) of drive plate, aligning the drive plate
hole position and torque converter.
CAUTION:
Be careful not to strike the drive plate when installing the
torque converter stud bolt.
 Align the position of tightening nuts ( ) for drive plate with those
of the torque converter, and temporarily tighten the nuts. Then,
tighten the bolts to the specified torque.
CAUTION:
 When turning crankshaft, turn it clockwise as viewed from the
front of the engine.
 When tightening the nuts for the torque converter after fixing
the crankshaft pulley bolts, confirm the tightening torque of
the crankshaft pulley mounting bolts. Refer to EM-79,
"Exploded View".
 Rotate crankshaft several turns and check that transaxle rotates freely without binding after con-
verter is installed to drive plate.
 Never reuse O-ring.
 Apply petroleum jelly to O-ring.
InspectionINFOID:0000000003849110
INSPECTION BEFORE INSTALLATION
After inserting a torque converter to transaxle assembly, check that
distance (A) is within the reference value limit.
INSPECTION AFTER INSTALLATION
Check the following items.
JPDIA0607ZZ
JPDIA0603ZZ
: 51 N·m (5.2 kg-m,38 ft-lb)
SCIA1861E
B: Scale
C : Straightedge
Distance A : Refer to TM-175, "Torque Converter".
JPDIA0620ZZ

TM-174
< SERVICE DATA AND SPECIFICATIONS (SDS) [CVT: RE0F09B]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General SpecificationINFOID:0000000003849115
*: Refer to MA-11, "Fluids and Lubricants".
Vehicle Speed When Shifting GearsINFOID:0000000003849116
Numerical value data are reference values.
(rpm)
CAUTION:
Lock-up clutch is engaged when vehicle speed is approximately 18 km/h (11 MPH) to 90 km/h (56 MPH).
Stall SpeedINFOID:0000000003849117
Line PressureINFOID:0000000003849118
kPa (bar, kg/cm2, psi)
Applied modelVQ35DE
2WD
CVT modelRE0F09B
CVT assembly model code number 1XE0A
Transmission gear ratioD range Variable
Reverse 1.766
Final drive 5.173
Recommended fluid Genuine NISSAN CVT Fluid NS-2*
Fluid capacity 10.2 liter (9 Imp qt)
CAUTION:
 Use only Genuine NISSAN CVT Fluid NS-2. Do not mix with other fluid.
 Using CVT fluid other than Genuine NISSAN CVT Fluid NS-2 will deteriorate in driveability and CVT durability, and may dam-
age the CVT, which is not covered by the warranty.
Throttle position Shift patternEngine speed
At 40 km/h (25 MPH) At 60 km/h (37 MPH)
8/8“D” position 2,900 – 4,100 3,900 – 5,600
Sport mode 2,900 – 4,100 3,900 – 5,600
“L” position 2,900 – 4,100 3,900 – 5,600
2/8“D” position 1,100 – 3,100 1,200 – 3,700
Sport mode 2,200 – 3,000 2,800 – 3,600
“L” position 2,900 – 3,800 3,900 – 4,800
Stall speed 2,700 – 3,500 rpm
Engine speedLine pressure
“R”, “D” and “L” positions
At idle 700 (7.00, 7.13, 101.5)
At stall 5,700 (57.00, 58.14, 826.5)

TM-176
< BASIC INSPECTION >[CVT: RE0F10A]
DIAGNOSIS AND REPAIR WORK FLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORK FLOW
Work FlowINFOID:0000000003806344
INTRODUCTION
The TCM receives signals from the vehicle speed sensor and PNP switch. Then it provides shift control or
lock-up control via CVT solenoid valves.
The TCM also communicates with the ECM by means of signals
sent from sensing elements used with the OBD-related parts of the
CVT system for malfunction-diagnostic purposes. The TCM is capa-
ble of diagnosing malfunctioning parts while the ECM can store mal-
functions in its memory.
Input and output signals must always be correct and stable in the
operation of the CVT system. The CVT system must be in good
operating condition and be free of valve seizure, solenoid valve mal-
function, etc.
It is much more difficult to diagnose a malfunction that occurs inter-
mittently rather than continuously. Most intermittent malfunctions are
caused by poor electric connections or improper wiring. In this case,
careful checking of suspected circuits may help prevent the replace-
ment of good parts.
A visual check only may not find the cause of the malfunctions. A
road test with CONSULT-III (or GST) or a circuit tester connected
should be performed. Follow the “DETAILED FLOW”.
Before undertaking actual checks, take a few minutes to talk with a
customer who approaches with a driveability complaint. The cus-
tomer can supply good information about such malfunctions, espe-
cially intermittent ones. Find out what symptoms are present and
under what conditions they occur. A “Diagnostic Work Sheet” as
shown on the example (Refer to TM-177
) should be used.
Start your diagnosis by looking for “conventional” malfunctions first.
This will help troubleshoot driveability malfunctions on an electroni-
cally controlled engine vehicle.
Also check related Service Bulletins.
DETAILED FLOW
1.COLLECT THE INFORMATION FROM THE CUSTOMER
Get the detailed information from the customer about the symptom (the condition and the environment when
the incident/malfunction occurred) using the diagnosis work sheet. Refer to TM-177, "
Diagnostic Work Sheet".
>> GO TO 2.
2.CHECK SYMPTOM 1
Check the following items based on the information obtained from the customer.
 Fail-safe. Refer to TM-283, "
Fail-safe".
 CVT fluid inspection. Refer to TM-304, "
Inspection".
 Line pressure test. Refer to TM-308, "
Inspection and Judgment".
SAT631IB
SAT632I
SEF234G

DIAGNOSIS AND REPAIR WORK FLOW
TM-177
< BASIC INSPECTION >[CVT: RE0F10A]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
 Stall test. Refer to TM-306, "Inspection and Judgment".
>> GO TO 3.
3.CHECK DTC
1. Check DTC.
2. Perform the following procedure if DTC is detected.
 Record DTC.
 Erase DTC. Refer to TM-202, "
Diagnosis Description".
Is any DTC detected?
YES >> GO TO 4.
NO >> GO TO 5.
4.PERFORM DIAGNOSTIC PROCEDURE
Perform “Diagnostic Procedure” for the displayed DTC.
>> GO TO 5.
5.PERFORM DTC CONFIRMATION PROCEDURE
Perform “DTC CONFIRMATION PROCEDURE” for the displayed DTC.
Is DTC detected?
YES >> GO TO 4.
NO >> GO TO 6.
6.CHECK SYMPTOM 2
Confirm the symptom described by the customer.
Is any malfunction present?
YES >> GO TO 7.
NO >> INSPECTION END
7.ROAD TEST
Perform “ROAD TEST”. Refer to TM-310, "
Description".
>> GO TO 8.
8.CHECK SYMPTOM 3
Confirm the symptom described by the customer.
Is any malfunction present?
YES >> GO TO 2.
NO >> INSPECTION END
Diagnostic Work SheetINFOID:0000000003806345
INFORMATION FROM CUSTOMER
KEY POINTS
WHAT..... Vehicle & CVT model
WHEN..... Date, Frequencies
WHERE..... Road conditions
HOW..... Operating conditions, Symptoms
Customer name MR/MS Model & Year VIN
Trans. Model Engine Mileage
Malfunction Date Manuf. Date In Service Date
Frequencyo Continuouso Intermittent ( times a day)

TM-178
< BASIC INSPECTION >[CVT: RE0F10A]
DIAGNOSIS AND REPAIR WORK FLOW
DIAGNOSTIC WORK SHEET
Symptomso Vehicle does not move. (o Any positiono Particular position)
o No shift
o Lock-up malfunction
o Shift shock or slip (o N → Do N → Ro Lock-upo Any drive position)
o Noise or vibration
o No pattern select
o Others
()
Malfunction Indicator (MI)o Continuously lito Not lit
1o Read the item on cautions concerning fail-safe and understand the customer's complaint.TM-283
2o CVT fluid inspection, stall test and line pressure test
o CVT fluid inspection
TM-304
o Leak (Repair leak location.)
o State
o Amount
o Stall test
TM-306
,
TM-308
o Torque converter one-way clutch
o Reverse brake
o Forward clutch
o Steel belto Engine
o Line pressure low
o Primary pulley
o Secondary pulley
o Line pressure inspection - Suspected part:
3o Perform self-diagnosis.
TM-204
Enter checks for detected items.
4o Perform road test.TM-310
4-1. Check before engine is started TM-310
4-2. Check at idleTM-311
4-3. Cruise testTM-312
o Check malfunction phenomena to repair or replace malfunctioning part after completing all road tests. Refer to TM-286,
"Symptom Table".
5o Drive vehicle to check that the malfunction phenomenon has been resolved.
6o Erase the results of the self-diagnosis from the TCM and the ECM.TM-202
,
TM-204