2008 NISSAN QUEST turn signal

HEADLIGHT AND TURN SIGNAL CON-
TROLLOW TIRE PRESSURE WARNING LIGHTWINDSHIELD WIPER/WASHER SWITCHSTEERING WHEEL SWITCHES FOR AU-
DIO CONTROL/BLUETOOTH 
CRUISE CONTROLLIGHTS ON DEMANDVEHICLE DYNAMIC CONTROL (VDC)
OFF SWITCHREAR SONAR SYSTEM OFF SWITCH
TILT AND TELESCOPIC STEERING COL-
UMNCONTROL PANEL DISPLAYCLIMATE CONTROLSFRONT PASSENGER AIR BAG STATUS
LIGHT
HAZARD WARNING SWITCH*AUDIO SYSTEMAUXILIARY AUDIO INPUT JACK*
*See your Owner’s Manual for more information.

TABLE OF CONTENTS
Remote Keyless Entry System..........................2
Windshield Wiper/Washer Switch .......................3
Headlight and Turn Signal Control .......................3
Lights on Demand (if so equipped) .......................4
Steering Wheel Switches for Audio Control/Bluetooth 
(if so equipped) .................................5
Cruise Control ...................................5
Auto Climate Control (if so equipped) .....................6
Rear Climate Control Dials ............................8
FM/AM/XM * Radio with CD Changer (if so equipped) ...........8
Control Panel Display with Navigation System (if so equipped) ......10
RearView Monitor (if so equipped) ......................10
Clock Set/Adjustment ..............................11
Rear Sonar System Off Switch (if so equipped) ...............11
Vehicle Dynamic Control (VDC) Off Switch (if so equipped) .......11
Automatic Driver Positioner (if so equipped) .................12
Outside Mirror Control Switch .........................13
Pedal Position Adjustment Switch .......................13
Front-Passenger Air Bag Status Light ....................13
Tire Pressure Monitoring System (TPMS) ..................14
Seat Belt Warning Light and Chime ......................14
Child Safety Rear Door Lock ..........................14
Fuel-Filler Door Release .............................14
Fuel-Filler Cap ..................................15
Moonroof Controls (if so equipped) ......................15
Power Sliding Doors and Power Lift Gate (if so equipped) ........15
Front Seat Adjustments .............................16
Adjusting and Folding the 2nd Row Seat ...................17
Folding the 3rd Row Seat ............................18
Homelink Universal Transceiver (if so equipped) ..............19
Bluetooth Hands-Free Phone System (if so equipped) ..........20
NISSAN Mobile Entertainment System (if so equipped) ..........22
Navigation System (if so equipped) ......................26
This easy-to-use Quick Reference Guide is intended to help you more fully
appreciate some of the unique features and functions of your new vehicle.
However, it is not intended to replace your Owner’s Manual. The Owner’s
Manual contains more detailed information to help you better understand the
important safety warnings, features, operation, and maintenance of your
vehicle.

WINDSHIELD WIPER/WASHER SWITCH
The ignition switch must be in the ON position to
activate the windshield wipers.
 Move the lever to the following positions to operate
the windshield wipers:
Intermittent (INT)– Front wipers operate in-
termittently andcanbefurther adjusted by
twisting the time control ring
.
Low Speed (LO)–Continuous low-speed
operation of front wipers.
High Speed (HI)–Continuous high-speed
operation of front wipers.
Mist (MIST) – Lift the lever up for one sweep of the front wipers.
Rear Wipers (REAR)– Twist the end section to operate the first (INT)or second
(ON) speed settings for the rear wipers.
 The washer function activates the washer fluid and several sweeps of the wipers:
● For FRONT WASHER, pull lever toward you.
● For REAR WIPER, push lever away from you.
HEADLIGHT AND TURN SIGNAL CONTROL
TO ACTIVATE THE AUTOLIGHT SYSTEM:
Turn the headlight control switchto the AUTO position
to activate the autolight system. The autolight system can:
 Turn the headlights on automatically when it is dark.
 Turn the headlights off automatically when it is light.
 Keep theheadlights onfor 45 seconds afteryouturn
the ignition switch to OFF and all doors are closed.
TO DEACTIVATE THE AUTOLIGHT SYSTEM:
 Turn the headlight control switchto the OFF,orposition.
HEADLIGHT CONTROL SWITCH
Turn the headlight control switchto theposition to turn on the front parking,
tail, license plate and instrument panel lights.
 Turn the headlight control switch
to theposition to turn on the headlights. All
other lights remain on.
3

FOG LIGHT OPERATION
NOTE:The headlights must be on and the low beams selected for the fog lights to operate.
 Turn the switch (inside collar)
to theposition to turn on the fog lights.
 Turn the switch (inside collar)
to the OFFposition to turn off the fog lights.
TURN SIGNAL SWITCH
Move the headlight control switch up or downto
signal a turning direction. When the turn is completed,
the turn signals cancel automatically.
 To signal alane change, movetheheadlight control
switch up or down
to the point where the indicator
light begins to flash, but the headlight control switch does not latch.
HIGH BEAM
 Push the headlight control switch forwardto se-
lect thehigh beam function. Theblue
indicator
light illuminates. Pulltheheadlight switchbacktothe
original position to select the low beam. The blue
indicator light goes off.
 Pull and release the headlight control switch
to flash the headlight high beams on
and off.
LIGHTS ON DEMAND (if so equipped)
The lights ondemand switchallowsthedriver toselect oneofthree
lighting modes for the interior lights and puddle lamps:
Push thetop portion ofthe switch andtheinterior lightsand
puddle lamps will illuminate. The lights will turn off automatically
after 30minutes toprevent thebattery frombecoming dis-
charged.
Push the switch to the neutral position and the lights will stay on for approximately 30
seconds when:
 The doors areunlocked bythe keyfob, akey, orthe power doorlockswitch whileall
doors are closed and the ignition switch is in the OFF position.
 The driver’s door is opened and then closed while the key is removed from the ignition
switch.
 The key is removed from the ignition switch while all doors are closed.
4

HOMELINKUNIVERSAL TRANSCEIVER (if so equipped)
SYSTEM OPERATING TIPS
 Garage doors, electrical gates, entry doors, etc. will be activated during programming.
To avoid injury, make sure that people and objects are clear of all doors or gates during
programming. Yourvehicle’s engineshouldbeturned offwhile programming the
HomeLink Transceiver.
 To program your HomeLink Transceiver to operate a garage door, gate, or entry door
opener, home or office lighting, you need to be at the same location as the device.
NOTE: Garage dooropeners (manufactured after1996) have“rolling codepro-
tection”. Toprogram agarage dooropener equipped with“rolling codeprotec-
tion”, you will need to use a ladder to get up to the garage door opener motor to
be able to access the “smart or learn” program button.
PROGRAMMING YOUR HOMELINK  UNIVERSAL TRANSCEIVER (Mirror,
Sun Visor or Overhead Console)
1. To begin, press and hold the two
outer HomeLink buttons (to
clear the memory) until the indi-
cator light blinks slowly (after 20
seconds) . Releasebothbut-
tons.
2. Position theend ofthe hand-
held transmitter 1-3inches
(26-76 mm)away fromthe
HomeLink surface
3. Using bothhands, simultaneously pressandhold both theHomeLink button you
want toprogram andthehand-held transmitter button. DONOT release the
buttons until step 4 has been completed.
4. Hold down both buttons until the indicator light on the HomeLink flashes, changing
from a“slow blink” to a“rapidly flashing blink”.Thiscould takeupto90 seconds.
When the indicator light flashes rapidly, both buttons may be released. The rapidly
flashing light indicates successful programming. To activate the garage door or other
programmed device, press and hold the programmed HomeLink button - releasing
when the device begins to activate.
5. If the indicator light on the HomeLink blinks rapidly for two seconds and then turns
solid, HomeLink has picked up a “rolling code” garage door opener signal. You will
need toproceed withthenext steps totrain theHomeLink to complete the
programming which may require a ladder and another person for convenience.
6. Press and release the “smart” or “learn” program button located on the garage door
opener’s motor to activate the “training mode”. This button is usually located near the
antenna wire that hangs down from the motor. If the wire originates from under a light
lens, you will need to remove the lens to access the program button.
19

WIRELESS HEADPHONES
Thewireless headphones includeseparate buttons
for power andvolume control. Headphones auto-
matically turnoffafter 30seconds ifno sound is
present.
For optimum wirelessheadphone performance, in-
crease the volume on the rear seat controller to the
maximum levelandadjust thewireless headphone
volume usingthevolume controlonthe wireless
headphone. Using a lower volume setting on the rear
seat controller can cause static noise in the wireless
headphone.
The wireless headphone audio signal originates from
the rear audio controls. Thissignal needs anunob-
structed path to the headphones to maintain perfor-
mance.
REMOTE CONTROL
Power Button
Stop Button
Next Track/Chapter
and Previous
Track/Chapter Button
Title Button
Enter Button
Display Button
Mode Button
Subtitle Button
Audio Button
Angle Button
Clear Button
Pause Button
Play Button
Fast Forward/Fast Reverse Button
Menu Button
Navigation Keys
Back Button
Numeric Keypad
25