2008 NISSAN LATIO service

WW-32
< SERVICE INFORMATION >
REAR WIPER AND WASHER SYSTEM
2. Clean pivot area as shown. This will reduce the possibility of
wiper arm looseness.
3. Install wiper blade.
4. Install wiper arm so that the arm rests in the stopper and tighten
rear wiper arm nut.
5. Install wiper arm cover.
REAR WIPER MOTOR
Removal
1. Remove wiper arm. Refer to "REAR WIPER ARM" .
2. Raise arm cap.
3. Remove the rear wiper motor nut, remove the rear wiper arm and blade.
4. Remove the back door lower finisher. Refer to EI-36, "
Removal and Installation" .
SEL024J
1. Rear wiper motor 2. Rear wiper arm and blade 3. Wiper arm cover
4. Pivot cap A. Wiper motor bolts B. Rear wiper motor nut
LKIA0788E

REAR WIPER AND WASHER SYSTEM
WW-33
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
L
MA
B
WW
N
O
P
5. Disconnect the rear wiper motor connector (B).
6. Remove the bolts (A) and remove the rear wiper motor (1).
Installation
Installation is in the reverse order of removal.
CAUTION:
Do not drop the wiper motor or cause it to contact other parts.
REAR WASHER TUBE LAYOUT
NOTE:
Connect the check valve (2) to the washer fluid tube (1) so that the
directional arrow on the check valve (2) points towards the washer
nozzle tube (3).
REAR WASHER NOZZLE
Removal
1. Remove the back door window garnish. Refer to EI-36, "Removal and Installation" .
2. Disconnect rear washer tube from rear washer nozzle.
LKIA0789E
1 Washer fluid reservoir 2 Washer fluid tube to rear door 3 Rear washer nozzle
4Check valve
LKIA0790E
WKIA4242E

WW-34
< SERVICE INFORMATION >
REAR WIPER AND WASHER SYSTEM
3. Release retaining clips and remove washer nozzle.
Installation
Installation is in the reverse order of removal.
NOTE:
Inspect rear washer nozzle for proper spray pattern, adjust as necessary. Refer to WW-34, "
Washer Nozzle
Adjustment" .
WASHER FLUID RESERVOIR
Refer to WW-22, "Removal and Installation of Washer Tank" .
WIPER AND WASHER SWITCH
Refer to WW-22, "Removal and Installation of Front Wiper and Washer Switch" .
WASHER MOTOR
Refer to WW-23, "Removal and Installation of Front Washer Motor" .
Washer Nozzle AdjustmentINFOID:0000000001704578
Adjust the washer nozzle to specification using suitable tool as
shown.
LKIA0545E
Adjustable range : ±15° (In any direction)
LKIA0349E
WEL912A

POWER SOCKET
WW-35
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
L
MA
B
WW
N
O
P
POWER SOCKET
Wiring Diagram - P/SCKT -INFOID:0000000001704579
Removal and InstallationINFOID:0000000001704580
REMOVAL
1. Remove the console mask. Refer to IP-10, "Component Parts" .
WKWA5835E

WW-36
< SERVICE INFORMATION >
POWER SOCKET
2. Remove the power socket (2) from the power socket ring (3),
while pressing the hook (A) on the ring out from square hole (B).
• Console mask (1)
• Power socket cutout (C)
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
Install the power socket with its cutout aligned with the power socket ring.
SKIB5671E

HORN
WW-37
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
L
MA
B
WW
N
O
P
HORN
Wiring Diagram - HORN -INFOID:0000000001704581
Removal and InstallationINFOID:0000000001704582
REMOVAL
1. Remove the front grille. Refer to EI-20, "Removal and Installation".
WKWA4997E

WW-38
< SERVICE INFORMATION >
HORN
2. Disconnect the horn connectors.
3. Remove the horn nuts (A) and remove the horns (1).
INSTALLATION
Installation is in the reverse order of removal.
SKIB5670E