When the front-passenger’s seat is occupied and the passenger meets the conditions
outlined inthe Owner’s Manual,the
willnotilluminate toindicate thatthe
front-passenger air bag is operational.
*When thesystem detects thatthefront-passenger’s seatisunoccupied, the
passenger air bag status light will not illuminate even though the front-passenger
air bag is OFF.
TIRE PRESSURE MONITORING SYSTEM (TPMS)
This system monitors tirepressure. Ifthe low tirepressure warning
light illuminates, check the tire pressure in all four tires.
Adjust the low tire pressure to the recommended COLD tire pressure
shown on the Tire and Loading Information label located in the driver’s
door opening. After tire pressures are adjusted, the vehicle will need
to be driven at speeds above 16 MPH (25 km/h) to activate the TPMS
and turn off the low tire pressure warning light.
SEAT BELT WARNING LIGHT AND CHIME
The light and chime remind you to fasten your seat belts. The light
illuminates whenevertheignition keyisturned tothe ON or
START position andremains illuminated untilthedriver’s seat
belt is fastened. At the same time, the chime sounds for approxi-
mately 6seconds unlessthedriver’s seatbeltissecurely fas-
tened.
The seat beltwarning lightmayalso illuminate ifthe front pas-
senger’s seatbeltisnot fastened whenthefront passenger’s
seat is occupied (if so equipped) . For 7 seconds after the ignition switch is in the ON
position, the system does not activate the warning light for the front passenger.
CHILD SAFETY REAR DOOR LOCK (Crew Cab model only)
Child safety locks help prevent the rear doors from being opened acci-
dentally, especially when small children are in the vehicle. The child safety
lock levers are located on the edge of the rear doors. When the lever is in
the LOCK position, the door can only be opened from the outside.
11
FOLD FLAT FRONT PASSENGER SEAT (if so equipped)
Tofold thefront passenger’s seatbackflatfor
extra storage lengthwhentransporting long
items:
Slide theseat tothe rearmost position.Lift
up on the recline lever
, located on the
outside edge of the seat, and fold the seat-
back forward as far as it will go.
Lift up on the latch
located on the upper corner of the seatback to release the back
of the seat.
Once the seatback is released, it will enable you to fold the front passenger seatback flat
over the seat cushion.
FOLDING THE REAR BENCH SEAT (Crew Cab Model only)
FOLDING THE SEATBACK DOWN:
To fold therear bench seatback downtoaccess the
jacking tools, pull up on the straps
located on the
outer edgeofthe seatbacks andfoldtheseatback
forward.
FOLDING THE SEAT BASE UP
To fold therear bench seatbase uptoaccess the
under-seat storage bins:
Lift up on the lever
located on the side of the
seat, while lifting up the front of the seat cushion.
Repeat thisprocess toraise andsecure theseat
cushion on the other side of the vehicle. Fold the
bottom of the seat cushion toward the back of the
vehicle until it locks into place.
Repeat thisprocess toraise andsecure theseat
cushion on the other side of the vehicle.
UTILITY BED WITH SPRAY-ON BED LINER AND UTILI-TRACK™
SYSTEM (if so equipped)
The Utili-track™ channel system allows you to move
tie-down clampsinthe bed tothe best location to
secure a load.
The tie-down cleatsmustbeinstalled sothe
clamp isproperly seatedinthe notches inthe
rail. Ifthe tie-down cleatisnot seated inthe
notches, itwill not beflush withtherailand
cannot beproperly tightened. Thebolt inthe
center of the cleat must be tightened hand-tight
(20 – 40 inch pounds) .
13
