2008 NISSAN 350Z ECU

CRUISE CONTROL (if so equipped)
To activate the cruise control, push theON·OFF
switch. The indicator light in the instrument panel will
illuminate.
To set cruising speed, accelerate the vehicle to the
desired speed, push theCOAST/SETswitch and
release it. The SET indicator light in the instrument
panel will illuminate.
To reset at a faster cruising speed, push and hold the
ACCEL/RESswitch. When the vehicle attains the
speed you desire, release the switch.
To reset at a slower cruising speed, push and hold
theCOAST/SETswitch. Release the switch when
the vehicle slows to the desired speed.
To cancel cruise control, push theCANCELswitch or tap the brake pedal. The SET
indicator light in the instrument panel will go out.
To resume a preset speed, push and release theACCEL/RESswitch. The vehicle
returns to the last set cruising speed when the vehicle speed is over 25 MPH (40 km/h) .
To turn off cruise control, push theON·OFFswitch. Both the CRUISE indicator light and
the SET indicator light in the instrument panel will go out.
SCREW-IN RECOVERY HOOK
Your vehicle is supplied with a screw-in recovery hook
for pulling the vehicle forward. For example: Pulling the
vehicle onto a flat bed for towing.
The screw-in recovery hook tool is located in the right
rear luggage compartment area under the cover along
with the vehicle jack.
To install the recovery hook:
Remove the recovery hook cover from the front grill.
Install the recovery hook as shown in the photo. Turn it
clockwise until securely tightened.
5

SEAT BELT WARNING LIGHT AND CHIME
The light and chime remind you to fasten your seat belts. The light
illuminates whenever the ignition key is turned to the ON or
START position and remains illuminated until the driver’s seat
belt is fastened. At the same time, the chime sounds for approxi-
mately 6 seconds unless the driver’s seat belt is securely fas-
tened.
The seat belt warning light may also illuminate if the front pas-
senger’s seat belt is not fastened when the front passenger’s
seat is occupied. For 7 seconds after the ignition switch is in the ON position, the system
does not activate the warning light for the front passenger.
FRONT SEAT ADJUSTMENTS
With manual seats:
Pull up on the lever under the front of the
seat and slide backward or forward to the
desired position. Release the lever to lock
the seat in position.
Lift the lever on the side of the seat to adjust
your seatback forward or backward; release
when you have found a comfortable angle
and the seat belt fits properly.
Turn either dial to adjust the angle and height of the seat cushion to the desired position.
With power seats (if so equipped):
Move the sliding switch
forward or
backward to adjust the seat cushion to the
desired position.
Move the reclining switch
forward or
backward to adjust the seatback to the de-
sired angle.
Turn either dial to adjust the angle and height of the seat cushion to the desired position.
SEATBACK TILT CANCEL SWITCH (Roadster only)
The passenger seat of the 350Z Roadster automatically tilts forward
when operating the soft top. This function can be cancelled by
pushing the seatback tilt cancel switch to theCANCELposition.
Push the seatback tilt cancel switch to theAUTOposition to reacti-
vate the power seatback tilt switch.
If the seatback tilt cancel switch is in theCANCELposition, the
seatback tilt paddle switch (located on the back of the passenger
seat) will not work. In this situation, tilt the passenger seatback
forward using the power seat position switch.
13

SOFT TOP OPERATION
Before opening or closing your soft top, refer
to the Owner’s Manual for detailed Warnings
and Cautions regarding soft top operation.
Open the top:
1. Make sure the area is clear of ob-
structions and that there is at least 6
feet of clearance above the vehicle.
2. Apply the parking brake and make
sure the transmission is in the P
(Park) position (automatic transmis-
sion) or the N (Neutral) position (manual transmission) .
3. Step on the brake pedal.
4. Start the engine.
5. Push the safety switch (black) located in the center of the top latch lever. Push the top
latch lever (silver) forward to unlatch the top.
6. Press and hold theOPENside of the
soft top operating switch until the
top is fully open and stowed and the
indicator light turns off.
Close the top:
1. Make sure the area is clear of ob-
structions and that there is at least 6
feet of clearance above the vehicle.
2. Apply the parking brake and make
sure the transmission is in the P
(Park) position (automatic transmission) or the
N (Neutral) position (manual transmission) .
3. Step on the brake pedal.
4. Start the engine.
5. Press and hold theCLOSEside of the soft top
operating switch until the top is fully closed and
the indicator light begins to flash.
6. Securely latch the top with the top latch lever.
The indicator light turns off.
If the top does not close when using the operating
switch, refer to the Owner’s Manual for the procedure
to manually close the top.
15