2008 MITSUBISHI SHOGUN ignition

4-64 Starting and driving
4
NOTE●
An operation noise may be emitted from the engine com- partment in the following situations. The sound is associ- ated with checking the operat
ions of the ASTC. At this
time, you may feel a shock from the brake pedal if youdepress it. These do not indicate a malfunction. • When the ignition switch is set to the “ON” position. • When the vehicle is driven for a while after the engine isturned on.
●
When the ASTC is activated,
you may feel a vibration in
the vehicle body or hear a whining sound from the enginecompartment. This indicates that the syst
em is operating normally. It
does not indicate a malfunction.
●
When the anti-lock brake syst
em warning lamp is illumi-
nated, the ASTC is not active.
●
On vehicles with the rear di
fferential lock, the ASTC and
ABS functions are suspended while the rear differential lock is activated. ASTC indication lamp, active stability control function OFF indication lamp, ABS warning lampand brake warning lamp are ill
uminated while these func-
tions are suspended. It does not indicate a problem. When the rear differential lock is
disengaged, these lamps go out
and function again. Refer to “Brake warning lamp” on page 3-13, “ABS warning lamp” on page 4-60, “Active stability controlfunction OFF indication lamp” on page 4-67.
ASTC indication lamp
E00618000035
The ASTC indication lamp shows the operating status of theactive stability control function and active traction control function. For details, see these sections of this owner’s manual: Active stability control function indication lamp
→ p. 4-67
Active traction control function indication lamp
→ p. 4-69
BK-BK2008E1ENUK.en-uk-Section7.fm Page
64 Wednesday, January 9, 2008 4:36 PM

Starting and driving
4-65
4
ASC OFF switch
E00620500024
The active stability control func
tion is automatically activated
when the ignition switch is turned to the “ON” position. You can deactivate the system by
pressing the ASC OFF switch
when the vehicle is stationary.To reactivate the active stabili
ty control function, press the
ASC OFF switch again.
It is strongly recommended that the
active stability control function normally be kept activated.LHD RHD
CAUTION
!●
For safety, operate the AS
C OFF switch with the
vehicle stationary.
BK-BK2008E1ENUK.en-uk-Section7.fm Page
65 Wednesday, January 9, 2008 4:36 PM

Starting and driving
4-67
4
Active stability control function indication lamp
E00614000125
The indication lamps should illuminate when the ignition switch is turned to the “ON” position and should go off after a few seconds.If the indication lamps stay on or do not illuminate when the ignition switch is turned to the “ON” position, we recommend you to have your vehicle inspected.
indication lamp blinks when
the active stability control
function is operating.
indication lamp illuminates when the active stability control
function is deactivated by either of the following operations: ●
The ASC OFF switch is presse
d to deactivate the system.
●
The transfer shift lever is
placed in the “4LLc” position.
Active stability control function indication lamp Active stability control function OFF indication lamp
CAUTION
!●
When indication lamp bl
inks, the active stability
control function is operating, which means that the road is slippery or that
your vehicle’s wheels are
spinning excessively. If this happens, drive slower with less accelerator input.
●
If a fault occurs in th
e device, the ABS warning
lamp or and indication lamps illuminate as warning. Park your vehicl
e in a safe place and stop
the engine. Then, start the engine again and check whether the ABS warning la
mp or and indica-
tion lamps go out. If the ABS warning lamp or and indication lamps remains lit even af
ter the engine has been
started, we recommend you to have your vehicle checked.
BK-BK2008E1ENUK.en-uk-Section7.fm Page
67 Wednesday, January 9, 2008 4:36 PM

4-68 Starting and driving
4
NOTE●
Immediately after reconnecti
on of the battery cable, the
indication lamp will illuminate and the active stability
control function will stop operating. If the vehicle is driven and the indication la
mp goes off, the active sta-
bility control function will again start operating. If the indication lamp illuminates again or illuminates even though the battery has not been disconnected, aninsufficient battery voltage or other problems may be the reason. We recommend you to have your vehicle inspected.
Active traction control function
E00614100041
The active traction control function maintains traction on slip-pery road surfaces by automatical
ly controlling the engine out-
put and applying the brakes
so the driving wheels are
prevented from spinning.The active traction control f
unction automatically turns ON
when the ignition switch is turned to the “ON” position.
CAUTION
!●
If the temperature in the
braking system increases
excessively due to conti
nuous brake control on a
slippery road surface,
a warning buzzer will sound
intermittently to warn the
driver. If driving contin-
ues in spite of the buzzer an
d the temperature in the
braking system increases
further, the indication
lamp will illuminate, th
e warning buzzer will sound
continuously for approx
imately 3 seconds, and
active traction control function operation will besuspended to protect the
braking system. (Normal
operation of the ve
hicle will not be
affected.) If the
vehicle is stopped and the indication lamp goes off, the active traction control function will start operating again.
BK-BK2008E1ENUK.en-uk-Section7.fm Page
68 Wednesday, January 9, 2008 4:36 PM

Starting and driving
4-69
4
Active traction control
function indication lamp
E00614200097
The indication lamp (1) should illuminate when the ignition switch is turned to the “ON” position and should go off after a few seconds.If the indication lamp stays on or does not illuminate when the ignition switch is turned to the “ON” position, we recommend you to have your vehicle inspected.When the active traction contro
l system operates, the active
traction control function indication lamp (1) blinks and the indication lamp for the wheel (2) being subjected to antispincontrol also blinks. Example indication: Active traction control function control- ling front-right wheel
NOTE●
In the event of a fault in the active stability control func- tion, the and indication lamps illuminate. As a result, an indication of the
active traction control function
is limited to flashing of the indication lamp for the wheel(2) being subjected to antispin control.
BK-BK2008E1ENUK.en-uk-Section7.fm Page
69 Wednesday, January 9, 2008 4:36 PM

4-70 Starting and driving
4
Cruise control
*
E00609100519
Cruise control is an automatic
speed control system that keeps
a set speed. It can be activated at about 40 km/h (25 mph) or more.NOTE●
Cruise control may not be able to keep your speed on uphills or downhills.
●
Your speed may decrease on
a steep uphill. You may use
the accelerator pedal if you want
to stay at your set speed.
●
Your speed may increase to mo
re than the set speed on a
steep downhill. You have to use the brake to control yourspeed. As a result, the set speed driving is deactivated.
CAUTION
!●
If the vehicle is towed with
the ignition switch in the
“ON” position and only the front wheels or only therear wheels raised off the
ground, the active traction
control function may operate
, resulting in an acci-
dent. When towing the vehi
cle with the front wheels
raised, keep the ignition
switch in the “LOCK” or
“ACC” position. When towi
ng the vehicle with the
rear wheels raised, keep th
e ignition switch in the
“ACC” position. Refer to “Towing” on page 6-29.
CAUTION
!●
When you do not wish to drive at a set speed, turn off the cruise control for safety.
●
Do not use cruise control
when driving conditions
will not allow you to stay at the same speed, such as in heavy traffic or on roads that are winding, icy,snow-covered, wet, slipp
ery, on a steep downhill
slope.
●
On vehicles with M/T, do not move the gearshift lever to the “N” (Neutral) position while driving at a set speed without depressing
the clutch pedal. The
engine will run too fast and might be damaged.
BK-BK2008E1ENUK.en-uk-Section7.fm Page
70 Wednesday, January 9, 2008 4:36 PM

4-72 Starting and driving
4
To activate
E00609300553
1. With the ignition switch in the “ON” position, press the
“ON OFF” switch (A) to turn
on the cruise control. The
“CRUISE” indication lamp in the meter cluster will come on.
NOTE●
If the cruise control is on when the ignition switch is turned to the “LOCK” or “ACC” position, cruise control will be on automatically the next time you start the engine. The “CRUISE” indication lamp will also be on.
●
If the battery voltage is insufficient, the memory data for the cruise control may be erased. As a result, the “CRUISE” indication lamp may not comeon when you restart the engine. If this happens, press the “O
N OFF” switch once again to
turn on the cruise control.
BK-BK2008E1ENUK.en-uk-Section7.fm Page
72 Wednesday, January 9, 2008 4:36 PM

Starting and driving
4-77
4
●
When the active stability & tr
action control (ASTC) starts
operating. Refer to “Active stability
& traction control (ASTC)” on
page 4-63.
Also, the set speed driving ma
y be deactivated as follows:
●
When the engine speed rises and approaches the tachome- ter’s red zone (the red-coloured part of the tachometer dial).
To resume the set speed
E00609800460
If the set speed driving is deactivated by the condition described in “To deactivate” on page 4-76, you can resume the previously set speed by pressi
ng the “ACC RES” switch (C)
while driving at a speed of about 40 km/h (25 mph) or higher. Under either of the following conditions, however, using the switch does not allow you to resume the previously set speed. In these situations, repeat
the speed setting procedure:
●
The “ON OFF” switch is pressed.
●
The ignition switch is turned OFF.
●
“CRUISE” indication lamp is turned OFF.
WARNING
!●
On vehicles with A/T, alth
ough the set speed driving
will be deactivated when shifting to the “N” (NEU-TRAL) position, never move the selector lever to the “N” (NEUTRAL) position while driving. You would have no engine
braking and could cause
a serious accident.CAUTION
!●
When the set speed driving is deactivated automati- cally in any situation other than those listed above, there may be a system malfunction.Press the “ON OFF” switch
to turn off the cruise
control and have it in
spected by a MITSUBISHI
MOTORS Authorized Service Point.
BK-BK2008E1ENUK.en-uk-Section7.fm Page
77 Wednesday, January 9, 2008 4:36 PM