Page 180 of 241
FRONT SEAT ASSEMBLY
TSB Revision
INTERIOR52A-19
INSPECTIONM1522005500287
CONTINUITY TEST OF HEATED SEAT SWITCH
.1. Check for continuity between terminals.
2. Check that the indicator is lighted at HI or LO when battery voltage is supplied to terminal 5 and terminal 8 is grounded.
3. Check that indicator is lighted when battery voltage is
supplied to terminal s 2 and terminal 6.
.
SEAT CUSHION HEATER CHECK
Measure the resistance between terminals.
Standard value: At room temperature 20 °C (68 °F)
Between terminals 1 and terminal 2
Standard type: Approximately 3.82 ± 4.66 ohms
Spots type: Approximately 4.47 ± 5.48 ohms
Between terminals 1 and terminal 4
Standard type: 8.90 ± 10.88 ohms
Spots type: 8.79 ± 10.75 ohms
.
ItemSwitch
positionTester
connectionSpecified
condition
Driver's
seat sideHI1 − 5, 3 − 8Continuity
exists (2
Ω
or less)
OFF1 − 5, 3 − 5, 5
− 8
Open
circuit
LO3 − 5Continuity
exists (2
Ω
or less)
Front
passenger'
s seat sideHI4 − 5, 8 − 9Continuity
exists (2
Ω
or less)
OFF4 − 5, 5 − 8, 5
− 9
Open
circuit
LO5 − 9Continuity
exists (2
Ω
or less)
ACX00625
AC610374
Page 181 of 241
FRONT SEAT ASSEMBLY
TSB Revision
INTERIOR52A-20
SEATBACK HEATER CHECK
Measure the resistance between terminals.
Standard value: At room temperature 20 °C (68 °F)
Standard type: 4.86 ± 5.94 ohms
Spots type: 4.06 ± 4.96 ohms
HEATED SEAT RELAY CONTINUITY CHECK
12
AC200100
Battery voltageTester
connectionSpecified
condition
Not applied3 − 4Open circuit
•Connect
terminal 1 to
the positive
battery
terminal
•Connect
terminal 2 to
the negative
battery
terminal
3 − 4Continuity
exists (2
Ω or
less)
AC610364
2
3
4
1
AB
Heated seat
relay
Page 182 of 241
Page 183 of 241
Page 184 of 241
REAR SEAT ASSEMBLY
TSB Revision
INTERIOR52A-23
REAR SEAT ASSEMBLY
REMOVAL AND INSTALLATIONM1522001800639
AC611154AB
43 ± 8 N·m
32 ± 6 ft-lb
1
23
4
43 ± 8 N·m
32 ± 6 ft-lb
5
Removal steps
1.Rear seat head restraint
>>C<<2.Rear seat cushion assembly
>>A<<3.Rear seatback assembly
4.Rear seat hook
5.Luggage room partition board
Removal steps (Continued)
Page 185 of 241
REAR SEAT ASSEMBLY
TSB Revision
INTERIOR52A-24
AC609245AB
11
410
10
5
3
9
8
2
6
7
21 ± 4 N·m
15 ± 3 ft-lb
21 ± 4 N·m
15 ± 3 ft-lb
38 ± 13 N·m
28 ± 10 ft-lb
43 ± 8 N·m
32 ± 6 ft-lb 43 ± 8 N·m
32 ± 6 ft-lb
43 ± 8 N·m
32 ± 6 ft-lb
43 ± 8 N·m
32 ± 6 ft-lb
Removal steps
1.Rear seat head restraint
>>C<<2.Rear seat cushion assembly
3.Rear seat hook
>>B<<4.Rear seatback side assembly (RH)
>>B<<5.Rear seatback side assembly (LH)
>>A<<6.Rear seatback assembly (RH)
>>A<<7.Rear seatback assembly (LH)
8.Spacer
9.Snap ring
10.Rear seat armrest
11 .Rear seat striker
Removal steps (Continued)
Page 186 of 241
REAR SEAT ASSEMBLY
TSB Revision
INTERIOR52A-25
INSTALLATION SERVICE POINTS
.
>>A<< INSTALLATION OF REAR SEATBACK
ASSEMBLY (LH)/REAR SEATBACK ASSEMBLY
(RH)
Place the center hinge bracket of the rear seatback assembly
(LH) on top of the center hinge bracket of the rear seatback
assembly (RH) for installation.
.
>>B<< INSTALLATION OF REAR SEATBACK SIDE
ASSEMBLY (LH)/RE AR SEATBACK SIDE
ASSEMBLY (RH)
Press the rear seatback side as sembly in the direction shown
in the illustration and fit the attachment wire into the hook
securely to install the rear seatback side assembly.
.
>>C<< INSTALLATION OF REAR SEAT CUSHION
ASSEMBLY
Fit the rear seat cushion into the rear seat hook securely.
AC609262
Center hinge
bracket of rear
seatback assembly
(RH)
Center hinge
bracket of rear
seatback assembly
(LH)
AB
AC609261
AB
Hook
Rear seatback
side assembly
Attachment
wire
AC609260AB
Rear seat
hook
Rear seat
cushion
assembly
Page 187 of 241
REAR SEAT ASSEMBLY
TSB Revision
INTERIOR52A-26
DISASSEMBLY AND ASSEMBLYM1522002000766
AC609246AB
5
5
5
1
4
3
2
6
7
N
N
Disassembly steps
1.Hog ring
2.Rear seat cushion cover
3.Rear seat cushion pad
4.Hog ring
5.Rear seat head restraint guide
6.Rear seatback cover
7.Rear seatback pad
Disassembly steps (Continued)
