2008 MITSUBISHI GRANDIS stop start

2-36 Seat and seat belts
2
When the ignition key is turned to the “ON” position, the warn-
ing lamp will come on and a tone will sound for about 6 sec-
onds. If the front seat belt remains unfastened approximately
1 minute later, the warning lamp will flash and the tone sound
intermittently (each 12 seconds) when the vehicle is driven. If
the passenger subsequently unfastens the seat belt while driv-
ing, the warning lamp and tone will issue further warnings.
And if the seat belt remains unfastened, the warning lamp and
tone will issue further warnings each time the vehicle starts
moving from a stop. When the seat belt is fastened, the warn-
ings will stop. NOTE●When luggage is placed on the front passenger seat, a sen-
sor in the seat cushion may, depending on the weight and
position of the luggage, cause the warning tone to sound
and the warning lamp to come on.
Adjustable seat belt anchor (front seats)
E00405000433
The seat belt anchor height can be adjusted.
Move the seat belt anchor (A) down with the lock knob (B)
depressed. To move the anchor up, slide it without depressing
the lock knob.
WARNING
!●In order to reduce the risk of serious or fatal injury
in an accident, always wear your own seat belt. Do
not allow anyone to ride in your vehicle unless he or
she is also seated and wearing a seat belt. Children
should additionally be restrained in a secure child
restraint system.
WARNING
!●When adjusting the seat belt anchor, set it at a posi-
tion that is sufficiently high so that the belt will
make full contact with your shoulder but will not
touch your neck.●Adjust the shoulder belt anchor only when the vehi-
cle is not in motion.●Make sure the anchor is securely locked in position
after adjusting it.
BK-XP08E1ENUK.en-uk.book Page 36 Monday, August 13, 2007 2:20 PM

4-2 Starting and driving
4Economical driving
E00600100372
For economical driving, there are some technical requirements
that have to be met. The prerequisite for low fuel consumption
is a properly adjusted engine. In order to achieve longer life of
the vehicle and the most economical operation, we recommend
you have the vehicle checked at regular intervals in accordance
with the service standards.
Fuel economy and generation of exhaust gas and noise are
highly influenced by personal driving habits as well as the par-
ticular operating conditions. The following points should be
observed in order to minimize wear of brakes, tyres and engine
as well as to reduce environmental pollution.StartingAvoid rapid acceleration and sudden starts; such operation will
result in higher fuel consumption.ShiftingShift only at an appropriate speed and engine speed. Always
use the highest gear possible.City trafficFrequent starting and stopping increases the average fuel con-
sumption. Use roads with smooth traffic flow whenever possi-
ble. When driving on congested roads, avoid use of a low gear
at high engine speeds.IdlingThe vehicle consumes fuel even during idling. Avoid extended
idling whenever possible.
SpeedThe higher the vehicle speed, the more fuel consumed. Avoid
driving at full speed. Even a slight release of the accelerator
pedal will save a significant amount of fuel.Tyre inflation pressureCheck the tyre inflation pressures at regular intervals. Low tyre
inflation pressure increases road resistance and fuel consump-
tion. In addition, low tyre pressures adversely affect tyre wear
and driving stability.LoadDo not drive with unnecessary articles in the luggage compart-
ment. Especially during city driving where frequent starting
and stopping is necessary, the increased weight of the vehicle
will greatly affect fuel consumption. Also avoid driving with
unnecessary luggage, etc., on the roof; the increased air resist-
ance will increase fuel consumption.Cold engine startingStarting of a cold engine consumes more fuel.
Unnecessary fuel consumption is also caused by keeping a hot
engine running. After the engine is started, commence driving
as soon as possible.Air conditioningThe use of the air conditioning will increase the fuel consump-
tion.
BK-XP08E1ENUK.en-uk.book Page 2 Monday, August 13, 2007 2:20 PM

4-6 Starting and driving
4Parking brake
E00600500666
To park the vehicle, first bring it to a complete stop, fully
engage the parking brake, and then move the gearshift lever to
1st (on an uphill) or Reverse (on a downhill) position, for vehi-
cles with M/T or set the selector lever to “P” (PARK) position
on A/T vehicles.To applyTo release1- Pull the lever up without pushing the button at the end of
hand grip.
1- Pull the lever up slightly.
2- Push the button at the end of hand grip.
3- Push the lever downward.
BK-XP08E1ENUK.en-uk.book Page 6 Monday, August 13, 2007 2:20 PM

Starting and driving
4-7
4
When parking on a hill, apply the parking brake and turn the
front wheels towards the kerb on a downhill grade, away from
the kerb on an uphill grade.
Parking
E00600600830
Parking on a hillTo prevent the vehicle from rolling into the street, follow these
procedures:Parking on a downhill slopeTurn the front wheels towards the kerb and move the vehicle
forward until the kerb side wheel gently touches the kerb.
Set the parking brake and place the gearshift lever into the
“R” (Reverse) position (with M/T) or the selector lever into the
“P” (PARK) position (with A/T).
If necessary, apply chocks to wheels.Parking on an uphill slopeTurn the front wheels away from the kerb and move the vehicle
back until the kerb side wheel gently touches the kerb.
Set the parking brake and place the gearshift lever into the
1st position (with M/T) or the selector lever into the
“P” (PARK) position (with A/T).
If necessary, apply chocks to wheels.NOTE●If your vehicle is equipped with A/T, be sure to apply the
parking brake before moving the selector lever to the
“P” (PARK) position. If you move the selector lever to the
“P” (PARK) position before applying the parking brake, it
may be difficult to disengage the selector lever from the
“P” (PARK) position when next you drive the vehicle,
requiring application of a strong force to the selector lever
to move from the “P” (PARK) position.
CAUTION
!●Before driving, be sure that the parking brake is
fully released and brake warning lamp is off.
If a vehicle is driven without releasing the parking
brake, the brake will be overheated, resulting in
ineffective braking and possible brake failure.●When you intend to apply the parking brake, firmly
press the brake pedal to bring the vehicle to a com-
plete stop before pulling the parking brake lever.
Pulling the parking brake lever with the vehicle
moving could make the rear wheels lock up, thereby
making the vehicle unstable.●If the brake warning lamp does not extinguish when
the parking brake is fully released, the brake system
may be abnormal. For details, refer to “Brake
warning lamp” on page 3-10.
BK-XP08E1ENUK.en-uk.book Page 7 Monday, August 13, 2007 2:20 PM

4-8 Starting and driving
4
Parking with the engine runningNever leave the engine running while you take a short
sleep/rest. Also, never leave the engine running in a closed or
poorly ventilated place. Leaving the engine running risks
injury or death from accidentally moving the gearshift lever
(M/T) or selector lever (A/T) or the accumulation of toxic
exhaust fumes on the passenger compartment.Where you parkYour front bumper can be damaged if you scrape it over kerbs
or parking stop blocks. Be careful when travelling up or down
steep slopes where your bumper can scrape the road.When leaving the vehicleAlways remove the key from the ignition switch and lock all
doors and the tailgate when leaving the vehicle unattended.
Always try to park your vehicle in a well lit area.
Steering wheel height adjustment
E00600700121
To adjust the steering wheel height, release the tilt lock lever
while holding the steering wheel by hand, and raise or lower
the steering wheel to the desired height.
After adjustment, securely lock the lever by pulling it upward.
WARNING
!●Do not park your vehicle in areas where combustible
materials such as dry grass or leaves can come in
contact with the hot exhaust, since fire could occur.
1- Locked
2- Release
WARNING
!●After adjusting to the desired height, check to be
sure that the lever is locked.●Do not attempt to adjust the steering wheel while
you are driving the vehicle.
BK-XP08E1ENUK.en-uk.book Page 8 Monday, August 13, 2007 2:20 PM

Starting and driving
4-13
4
Mirror retractor switchWhen entering a restricted space, outside mirrors can be folded
away by pressing a switch inside the vehicle.
Push the switch to fold the mirrors to the rear.
To bring mirrors back into the original position, push the
switch again.
The mirrors can be extended and retracted for 30 seconds after
the ignition switch is turned to the “LOCK” position.
Either the mirror switch in the cabin or the remote controller of
the keyless entry system (if so equipped) can be used.
For information on the keyless entry system, refer to page 1-5.
NOTE●It is also possible to fold and return the mirrors by hand.
●When freezing has occurred and mirrors fail to operate as
intended, please refrain from repeated pushing of the
retractor switch as this action can result in burn-out of the
mirror motor circuits.Automatic extension of mirrorsIf the engine is stopped and started with the mirrors retracted,
the mirrors automatically extend for safety when the vehicle
speed reaches 30 km/h (19 mph).NOTE●If the mirrors are retracted manually or using the mirror
switch after the engine is started, they do not extend auto-
matically. Use the mirror switch to extend the mirrors, or
turn the ignition switch to the “LOCK” position to acti-
vate the automatic extension function.
BK-XP08E1ENUK.en-uk.book Page 13 Monday, August 13, 2007 2:20 PM

4-14 Starting and driving
4
Heated mirrors
E00601200077
When the rear window demister switch is pressed, the outside
rear-view mirrors are demisted or defrosted. Current will flow
through the heater element inside the mirrors, thus clearing
away frost or condensation.
The indicator lamp (C) will illuminate while the demister is on.
The heater will be turned off automatically in about 20 min-
utes.
Ignition switch
E00601401076
LOCKThe engine is stopped and the steering wheel locked. The key
can be inserted and removed only when the switch is in this
position.ACCThe engine is stopped, but the electrical devices such as the
radio and cigarette lighter can be operated.ONThe engine is running, and all the vehicle’s electrical devices
can be operated.STARTThe starter motor operates. After the engine has started, release
the key and it will automatically return to the “ON” position.M/T A/T
BK-XP08E1ENUK.en-uk.book Page 14 Monday, August 13, 2007 2:20 PM

4-16 Starting and driving
4
For vehicles with A/T, when removing the key, first set the
selector lever to the “P” (PARK) position, and then turn the key
to the “LOCK” position, then remove the key.A/T
CAUTION
!●Do not remove the ignition key from the ignition
switch while driving. The steering wheel will locked,
causing loss of control.●If the engine is stopped while driving, the brake ser-
vomechanism will cease to function and braking
efficiency will deteriorate. Also, the power steering
system will not function and it will require greater
manual effort to operate the steering.●Do not leave the key in the “ON” position for a long
time when the engine is not running, doing so will
cause the battery to be discharged.●Do not turn the key to the “START” position when
the engine is running, doing so could damage the
starter motor.
BK-XP08E1ENUK.en-uk.book Page 16 Monday, August 13, 2007 2:20 PM