2008 MITSUBISHI GRANDIS lock

8-38 Maintenance
8
Engine compartment fuse location tableEngine compartment fuse location
Front
No.
Symbol
Electrical system
Capacity
1——
-*
1
Battery
60 A*
2
2 Radiator fan motor50 A*
1
40 A*
2
3 Anti-lock braking system 30 A
4 Anti-lock braking system 40 A
5 Electric window system 40 A
6 Front fog lamps 15 A
7AC power supply
15 A*
1
Accessory socket
Accessory socket
15 A*
2
8Horn 10 A
9 Engine control20 A*
1
10 A*
2
10 Air conditioning 10 A
11 Stop lamps 15 A
12Horn
15 A*
1
Wiper deicer
——
-*
2
BK-XP08E1ENUK.en-uk.book Page 38 Monday, August 13, 2007 2:20 PM

8-40 Maintenance
8
●Some fuses may not be installed on your vehicle, depend-
ing on the vehicle model or specifications.
●The table above shows the main equipment corresponding
to each fuse.Identification of fuse
Fuse replacement 1. Before replacing a fuse, always turn off the electrical cir-
cuit concerned and place the ignition switch in the
“LOCK” position.
No.
Symbol
Electrical system
Capacity
1 Condenser fan 30 A
2 Engine control 30 A
3 Control flap 10 A
4 Glow relay 10 A
5 Valve block 10 A
6 Immobilizer 7.5 A
7 Heating pipe 10 A
7.5 A Brown
10 A Red
15 A Blue
20 A Yellow
25 A Transparent
30 A Green (fuse type) / Pink (fusible link type)
40 A Green
50 A Red
60 A Yellow (fusible link type)
LHD
BK-XP08E1ENUK.en-uk.book Page 40 Monday, August 13, 2007 2:20 PM

Maintenance
8-43
8
4. Insert a new fuse of the same capacity by using the fuse
puller and insert the fuse at the same place in the fuse
block.
Replacement of lamp bulbs
E01003100622
Before replacing a bulb, ensure the lamp is off. Do not touch
the glass part of the new bulb with your bare fingers; the skin
oil left on the glass will evaporate when the bulb gets hot and
the vapor will condense on the reflector and dim the surface.NOTE●If you are unsure of how to carry out the work as required,
we recommend you to consult a specialist.
●Be careful not to scratch the vehicle body when removing
a lamp and lens.
●When it rains, or when the vehicle has been washed, the
inside of the lens sometimes becomes foggy. This is the
same phenomenon as when window glass mists up on a
humid day, and does not indicate a functional problem.
When the lamp is switched on, the heat will remove the
fog. However, if water gathers inside the lamp, we recom-
mend you to have it checked.
CAUTION
!●If the newly inserted fuse blows again after a short
time, we recommend you to have the electrical sys-
tem checked to find the cause and rectify it.●Never use a fuse with a capacity larger than that
specified or any substitute, such as wire, foil, etc.;
doing so will cause the circuit wiring to heat up and
could cause a fire.
CAUTION
!●Bulbs are extremely hot immediately after being
turned off.
When replacing a bulb, wait for it to cool sufficiently
before touching it. You could otherwise be burnt.
BK-XP08E1ENUK.en-uk.book Page 43 Monday, August 13, 2007 2:20 PM

Maintenance
8-45
8
Inside
E01003400986
Headlamps
E01003500929
Replacement of low beam (halogen lamp type)1. Pull out the connector (B) while pressing the tab (A). Turn
the cap (C) anticlockwise and remove it.
1- Rear personal lamps: 8 W
2- Room lamp & map lamps: 8 W
3- Vanity mirror lamps*: 3 W
4- Glove box lamp: 1.4 W
5- Door lamps: 3.4 W
6- Luggage compartment lamp: 5 W
BK-XP08E1ENUK.en-uk.book Page 45 Monday, August 13, 2007 2:20 PM

8-48 Maintenance
8
Replacement of high beam Petrol-powered vehicles1. Pull out the connector (B) while pressing the tab (A). Turn
the cap (C) anticlockwise and remove it.
Diesel-powered vehicles1. Remove the bolt (A) to remove the power steering reser-
voir tank (B).
BK-XP08E1ENUK.en-uk.book Page 48 Monday, August 13, 2007 2:20 PM

Maintenance
8-49
8
Pull out the connector (D) while pressing the tab (C). Turn
the cap (E) anticlockwise and remove it.2. Turn the bulb socket (D) anticlockwise to remove it.
BK-XP08E1ENUK.en-uk.book Page 49 Monday, August 13, 2007 2:20 PM

Maintenance
8-51
8
Position lamps
E01003700279
Have the position lamps bulbs replaced by a MITSUBISHI
MOTORS Authorized Service Point.
Front turn-signal lamps
E01003800081
Turn the bulb socket anticlockwise to remove it. And remove
the bulb from the socket by pulling it out.
BK-XP08E1ENUK.en-uk.book Page 51 Monday, August 13, 2007 2:20 PM

Maintenance
8-53
8
3. Remove the entire socket and bulb assembly (E) by turn-
ing it anticlockwise.
CAUTION
!●Handle halogen lamp bulb with care. The gas inside
halogen lamp bulb is highly pressurized, so drop-
ping, knocking, or scratching a halogen lamp bulb
can cause it to shatter.●Never hold the halogen lamp bulb with a bare hand,
dirty glove, etc.
The oil from your hand could cause the bulb to
break the next time the fog lamps are operated.
If the glass surface is dirty, it must be cleaned with
alcohol, paint thinner, etc., and refit it after drying it
thoroughly.
BK-XP08E1ENUK.en-uk.book Page 53 Monday, August 13, 2007 2:20 PM