2008 MITSUBISHI COLT seat belts

2-36 Seat and seat belts
2
Suitability for various seating positionsE00406800571
Vehicles with rear bench seat*
*1: With front passenger’s air bag deactivated by means of front passenger’s air bag ON-OFF switch
Key of letters to be inserted in the above table:
●U - Suitable for “universal” category restraints approved for use in this mass group.
● UF - Suitable for forward-facing “ universal” category restraints approved for use in this mass group.
● L - Suitable for particular child restraints (MITSUBI SHI MOTORS genuine parts).
● B - Built-in restraint approved for this mass group.
● X - Seat position not suitable for children in this mass group.
Mass Group
Seating Position
Front Passenger
Rear OutboardRear CentreWithout Air Bag
With Air Bag
Activated
Air BagDeactivated
Air Bag*1
0 - Up to 10 kg (0-9 months) UX UXX
0+ - Up to 13 kg (0-2 years) U, L*
2UFU, L*2L*2X
I - 9 to 18 kg (9 months - 4 years) U, L*
3UF, L*3U, L*3L*3L*3
II & III - 15 to 36 kg (4-12 years) UUF U
L*4X

Seat and seat belts2-37
2
L (Genuine part information)

NOTE● The above suitability table applies to retention of child restraints using seat belts.
● When MITSUBISHI MOTORS genuine part No. MZ313200 is used on the rear seat, it can also be retained by means of ISO-
FIX child restraint mountings.
● There is no applicable MI TSUBISHI MOTORS Genuine Part for the Mass Group “0-Up to 10 kg (0-9 months)”.
MITSUBISHI MOTORS Europe B.V. reserves the right to make changes without any prior notification.
For detailed information, please consult your MI TSUBISHI MOTORS Authorized Service Point.
Genuine parts No.ECE No.
*2MZ312807 E1-04301146
*
3
MZ312745 E1-04301136
MZ313045 E1-04301133
MZ313200
*
4MZ312808 E1-04301148

2-38 Seat and seat belts
2
Vehicles with rear separated seat (5-door models)*
*1: With front passenger’s air bag deactivated by means of front passenger’s air bag ON-OFF switch
Key of letters to be inserted in the above table:
●U - Suitable for “universal” category restraints approved for use in this mass group.
● UF - Suitable for forward-facing “ universal” category restraints approved for use in this mass group.
● L - Suitable for particular child restraints (MITSUBI SHI MOTORS genuine parts).
● B - Built-in restraint approved for this mass group.
● X - Seat position not suitable for children in this mass group.
Mass Group
Seating Position
Front Passenger
Rear OutboardRear CentreWithout Air Bag
With Air Bag
Activated
Air BagDeactivated
Air Bag*1
0 - Up to 10 kg (0-9 months) UX UUX
0+ - Up to 13 kg (0-2 years) U, L*
2UFU, L*2U, L*2X
I - 9 to 18 kg (9 months - 4 years) U, L*
3UF, L*3U, L*3U, L*3L*3
II & III - 15 to 36 kg (4-12 years) UUF U
U, L*4X

Seat and seat belts2-39
2
L (Genuine part information)

NOTE● The above suitability table applies to retention of child restraints using seat belts.
● When MITSUBISHI MOTORS genuine part No. MZ313200 is used on the rear seat, it can also be retained by means of ISO-
FIX child restraint mountings.
● There is no applicable MI TSUBISHI MOTORS Genuine Part for the Mass Group “0-Up to 10 kg (0-9 months)”.
MITSUBISHI MOTORS Europe B.V. reserves the right to make changes without any prior notification.
For detailed information, please consult your MI TSUBISHI MOTORS Authorized Service Point.
Genuine parts No.ECE No.
*2MZ312807 E1-04301146
*
3
MZ312745 E1-04301136
MZ313045 E1-04301133
MZ313200
*
4MZ312808 E1-04301148

2-40 Seat and seat belts
2
Installing a child restraint system to the lower
anchorage (ISOFIX child restraint mountings)
E00408900228
Your vehicle’s rear seat is fitted with lower anchorages for
attaching a child restraint sy stem with ISOFIX mountings.
Child restraint system with ISOFIX mountingsE00409000473
The child restraint system is designed only for seats that incor-
porate lower anchorages. Retain the child restraint system
using the lower anchorages.
It is not necessary to retain th e child restraint system using the
vehicle’s seat belts. Only a MITSUBISHI MOTORS genuine
child restraint system can be used.
Genuine parts No. : MZ313200
ECE No. : E1-04301133
A: Child restraint system connectors

Seat and seat belts2-41
2
To i n s t a l l
1. Slide the rear seats to the fully backward position. (Refer
to “To adjust forward or backward” on page 2-9.)
2. Push the child restraint syst em’s connectors (A) into the
slit (B) in accordance with the instructions provided by
the child restraint system’s manufacturer.WARNING!
● If a child restraint system other than a
MITSUBISHI MOTORS genuine one is used, it may
not be properly retained an d the child could be seri-
ously injured as a result. Use only a MITSUBISHI
MOTORS genuine child restraint system.
A: Connector
B: Slit
C: Vehicle seatback
D: Vehicle seat cushion E: Lower anchorage

2-42 Seat and seat belts
2
3. Push and pull the child restraint system in all directions to
be sure it is firmly secured.
To remove
Remove the child restraint in accordance with the instructions
provided by the child rest raint system’s manufacturer.
Installing a child restraint system to a 3-point
type seat belt (with emergency/automatic locking
mechanism)
E00407000411
The 3-point type seat belts at the rear seating position can be
converted from normal emerge ncy locking retractor (ELR)
mode to automatic locking retractor (ALR) mode. It must be so
converted, when installing a child restraint system.WARNING!
●If there is any foreign mat erial in or around the con-
nectors, remove it befo re installing the child
restraint system. Make sure the seat belt is away
from, not looped through or otherwise interfering
with, the child restraint sy stem. If foreign matter is
not removed and/or the seat belt interferes with the
child restraint system, the child restraint system will
not be secured properly and could move forward in
the event of sudden braking or a collision, seriously
injuring the child and possibly other vehicle occu-
pants.
● When the vehicle is moving , do not adjust the seat
where the child restrain t system is installed.

Seat and seat belts2-43
2
To i n s t a l l
1. Place the child restraint system in the rear seating positionas shown in the illustration.
2. Route the belt through the child restraint according to the
child restraint system manuf acturer’s instructions, then
insert the latch plate into the buckle. 3. To activate the ALR mode, slowly pull the shoulder part
of the belt all the way out until it stops, then let the belt
feed back into the retractor.
4. After the belt has retracted, tug on it. If the belt is locked, you will not be able to pull it out. If you can pull the belt
out, it is not locked and you will need to repeat these
steps.