2008 MERCEDES-BENZ SL55AMG display

157 Controls in detail
Control system
If conditions have occurred causing status
messages to be recorded, the number of
messages appears in the right multifunc-
tion display:
1Number of recorded status messages
Press button k or j.
The stored messages will now be dis-
played in the order in which they have
occurred. For malfunction and warning
messages, see “Vehicle status messag-
es in the multifunction display”
(
page 359).Should the vehicle’s system record any
conditions while driving, the number of
messages will reappear in the multifunc-
tion display

when the SmartKey in the starter
switch is turned to position0 or
removed from the starter switch
or

when you turn off the engine by press-
ing the KEYLESS-GO* start/stop
button on the gear selector lever once
and open the driver’s door (this puts
the starter switch in position 0, same
as with the SmartKey removed from
the starter switch)
Settings menu
In the
Settings menu there are two
functions:

The function Reset, with which you can
reset most settings to those set at the
factory.

A collection of submenus with which
you can make individual settings for
your vehicle.
The following settings and submenus are
available:
iAfter you have scrolled through all recorded
status messages, the first recorded message
appears again.
iThe vehicle status message memory will be
cleared when you then turn the SmartKey in the
starter switch to position 1 or 2, or when you
press the KEYLESS-GO* start/stop button once
or twice without depressing the brake pedal. You
will then only see high priority messages in the
multifunction display (
page 359).
FunctionPage
Resetting all settings158
Submenus in the Settings menu158
Instrument cluster submenu160
Time submenu161
Lighting submenu163
Vehicle submenu166
Convenience submenu166

158 Controls in detail
Control system
Resetting all settings
You can reset the functions of most of the
submenus to the factory settings.
For safety, the
Light Circuit Headlamp
Mode
submenu in the Lighting menu can
be reset with the vehicle at standstill only.
Press button è or ÿ repeatedly
until the
Settings menu appears in the
multifunction display.
Press the reset button in the instru-
ment cluster for approximately
3 seconds.
In the right multifunction display you
will see the request to press the reset
button again to confirm.
Press the reset button again.
The functions of most submenus will
reset to factory settings.
Submenus in the Settings menu
Press button è or ÿ repeatedly
until the
Settings menu appears in the
multifunction display.
Press button j.
In the right multifunction display you
see the collection of submenus. There
are more submenus than can be simul-
taneously displayed.
Press button ç.
The selection marker moves to the next
submenu.
Scroll down with the ç button,
scroll up with the æ button.
With the selection marker on the de-
sired submenu, use the j button to
access the individual functions within
that submenu.
Once within the submenu, use
thej button to move to the next
function or the k button to move to
the previous function within that sub-
menu.
Use buttons æ or ç to change
the settings of the respective function.
iThe settings you have changed will not be
reset unless you confirm the action by pressing
the reset button a second time.

159 Controls in detail
Control system
The table below shows what settings can
be changed within the various menus.
Detailed instructions on making individual
settings can be found on the following
pages.
Instrument clusterTimeLightingVehicleConvenience
(page 160)(page 161)(page 163)(page 166)(page 166)
Selecting speedometer
display modeSynchronizing time with
head unitSetting daytime running
lamp mode (USA only)Setting automatic lockingActivating
easy-entry/exit feature
Selecting standard
displaySetting the time (hour)Setting locator lighting
Selecting languageSetting the time
(minutes)Setting night security
illumination
Setting interior lighting
delayed switch-off

160 Controls in detail
Control system
Instrument cluster submenu
Access the
Inst. Cluster submenu via
the
Settings menu. Use the Inst.
Cluster
submenu to change the instru-
ment cluster display settings. The follow-
ing functions are available:Selecting speedometer display mode
Move the selection marker with
buttonæ or ç to the
Inst. Cluster submenu.
Press button j or k
repeatedly until the message
Digital Speedometer appears in the
multifunction display.
The selection marker is on the current
setting.
Press button æ or ç to set the
speedometer units to
Kilometers or
Miles.Selecting language
Move the selection marker with
buttonæ or ç to the
Inst. Cluster submenu.
Press button j or k repeatedly
until the message
Language appears in
the multifunction display.
The selection marker is on the current
setting.
FunctionPage
Selecting speedometer display
mode160
Selecting language160
Selecting standard display161

161 Controls in detail
Control system
Press button æ or ç to select
the language to be used for the
multifunction display messages.
Available languages:

German

English

French

Italian

Spanish

Dutch

Swedish

Danish

Turkish

PortugueseSelecting standard display
Move the selection marker with
buttonæ or ç to the
Inst. Cluster submenu.
Press button j or k repeatedly
until the message
Select Display ap-
pears in the multifunction display.
The selection marker is on the current
setting.
Press button æ or ç to select
the desired setting.
The selected option appears in the left
multifunction display.
The option not selected will appear in
the right multifunction display when
scrolling through the standard display
(
page 149).Time submenu
Access the
Time submenu via the Settings
menu. Use the
Time submenu to change
the time and date settings. The following
functions are available:
Synchronizing time with head unit
Move the selection marker with
theæ or ç button to the
Time
submenu.
Press button j or k repeatedly
until the message
Time Synchron.
With Head Unit
appears in the multi-
function display.
The selection marker is on the current
setting.
FunctionPage
Synchronizing time with head
unit161
Setting the time (hour)162
Setting the time (minutes)162

162 Controls in detail
Control system
Press button æ or ç enable or
disable this feature.
When you set this feature to
On, the time
displayed in the multifunction display is
automatically synchronized with the time
of the COMAND system.Setting the time (hour)
This function is only available if the func-
tion
Time Synchron. With Head Unit
(
page 161) has been set to Off. The time
is then not set automatically by the
COMAND and must be set manually if
required.
Move the selection marker with
theæ or ç button to the
Time
submenu.
Press button j or k repeatedly
until the message
Set Time Hour
appears in the multifunction display.
The selection marker is on the hour
setting.
Press button æ or ç to set the
hour. Setting the time (minutes)
This function is only available if the func-
tion
Time Synchron. With Head Unit
(
page 161) has been set to Off. The time
is then not set automatically by the
COMAND and must be set manually if
required.
Move the selection marker with
theæ or ç button to the
Time
submenu.
Press button j or k repeatedly
until the message
Set Time Minute(s)
appears in the multifunction display.
The selection marker is on the minute
setting.
Press button æ or ç to set the
minutes.
iFor information on setting the time, refer to
the separate COMAND operating instructions.

163 Controls in detail
Control system
Lighting submenu
Access the
Lighting submenu via the
Settings menu. Use the Lighting sub-
menu to change the lamp and lighting set-
tings on your vehicle. The following
functions are available:Setting daytime running lamp mode
(USA only)
Move the selection marker with
buttonæ or ç to the
Lighting
submenu.
Press button j or k repeatedly
until the message
Light Circuit
Headlamp Mode
appears in the multi-
function display.
The selection marker is on the current
setting.
Press button æ or ç to select
manual operation (
Manual) or daytime
running lamp mode (
Constant).With daytime running lamp mode activated
and the exterior lamp switch in
positionM or U the low beam head-
lamps are switched on when the engine is
running.
In low ambient light conditions the follow-
ing lamps will switch on additionally:

Parking lamps

Tail lamps

License plate lamps

Side marker lamps
For more information on the daytime run-
ning lamp mode, see “Lighting”
(
page 131).
FunctionPage
Setting daytime running lamp
mode (USA only)163
Setting locator lighting164
Setting night security illumina-
tion164
Setting interior lighting delayed
switch-off 165
iThis function is not available in countries
where the daytime running lamp mode is manda-
tory and therefore in a constant mode.
iFor safety reasons, resetting to factory
settings (
page 158) while driving will not
deactivate the daytime running lamp mode.
The following message appears in the multifunc-
tion display:
Cannot be fully reset to
factory settings while driving.

164 Controls in detail
Control system
Setting locator lighting
With the locator lighting feature activated
and the exterior lamp switch in
positionU, the following lamps will
switch on during darkness when the
vehicle is unlocked using button Πon
the SmartKey or SmartKey with
KEYLESS-GO*:

Parking lamps

Tail lamps

License plate lamps

Front fog lamps

Side marker lamps
The locator lighting switches off when the
driver’s door is opened.
If you do not open a door after unlocking
the vehicle with the SmartKey, the lamps
will switch off automatically after approxi-
mately 40 seconds.
Move the selection marker with
buttonæ or ç to the
Lighting
submenu.
Press button j or k repeatedly
until the message
Locator Lighting
appears in the multifunction display.
The selection marker is on the current
setting.
Press button æ or ç to switch
the locator lighting feature
On or Off.
Turn the exterior lamp switch to
position U when exiting the vehicle.
The locator lighting feature is
activated.Setting night security illumination
(Headlamps delayed switch-off feature)
Use this function to set whether you would
like the exterior lamps to remain on for
15 seconds during darkness after exiting
the vehicle and closing the doors.
With the headlamps delayed switch-off
feature activated and the exterior lamp
switch in position U before the engine
is turned off, the following lamps will
switch on when the engine is turned off:

Parking lamps

Tail lamps

License plate lamps

Side marker lamps

Front fog lamps
If after turning off the engine you do not
open a door or do not close an opened
door, the lamps will switch off auto-
matically after 60 seconds.