2008 MERCEDES-BENZ SL55AMG high beam

25 At a glance
Cockpit
ItemPage
1Exterior lamp switch57, 131
2Headlamp cleaning button185
3Cruise control lever

Cruise control

Distronic*
214
218
4Shift paddle*: downshift180
5Instrument cluster26, 140
6Multifunction steering
wheel30, 144
7Shift paddle*: upshift180
8Lever for Voice Control
System*, see separate
operating instructions
ItemPage
9Front Parktronic* warning
indicator235
aDigital clock
bInterior storage compart-
ments (locking/unlocking)240
cOverhead control panel33
dGlove box238
eCenter console31, 32
fStarter switch40
gHorn
hSteering wheel adjustment
stalk46
ItemPage
jCombination switch

High beam

Turn signals

Windshield wipers
57
57
58
kParking brake pedal55, 63
lParking brake release
handle55
mHood lock release282
nDoor control panel36
oPower window switch201

29 At a glance
Instrument cluster
ItemPage
5Tachometer with:142
AHigh beam head-
lamp indicator lamp135
úEngine malfunction
indicator lamp,
USA only
±Engine malfunction
indicator lamp,
Canada only346
CRoll bar warning
lamp351
-Antilock Brake Sys-
tem (ABS) indicator
lamp344
1Supplemental
Restraint System
(SRS) indicator lamp354
ItemPage
XCombination low tire
pressure/TPMS mal-
function telltale,
USA only
Low tire pressure
telltale*,
Canada only355
6Right multifunction
display with:

Trip odometer143

Gear selector lever
position174

Gear range indicator177

Program mode indicator178
7Fuel gauge with:
AFuel reserve warning
lamp350

40 Getting started
Unlocking
Enter the vehicle.
Opening a door causes its window to open
slightly. It will fully close when the door is
shut.
For more information, see “SmartKey with
KEYLESS-GO*” (
page 108).
Starter switch positions
SmartKey
Starter switch
0For removing SmartKey
1Power supply for some electrical
consumers, such as seat adjustment
2Ignition (power supply for all electrical
consumers) and driving position
All lamps (except high beam headlamp
indicator lamp and turn signal indicator
lamps unless activated) in the instru-
ment cluster come on. If a lamp in the
instrument cluster fails to come on
when the ignition is switched on, have
it checked and replaced if necessary.
If a lamp in the instrument cluster
remains on after starting the engine or
comes on while driving, refer to “Lamps
in the instrument cluster”
(
page 342).
3Starting position
!A side window will not work if it is blocked
with ice or if the battery needs charging. If you
cannot shut a door, do not force it or you could
damage the door or the side window.
Fix whatever is affecting the window before
trying to shut the door.
Warning!G
When leaving the vehicle, always remove the
SmartKey or SmartKey with KEYLESS-GO*
from the starter switch, take it with you, and
lock the vehicle. Do not leave children unat-
tended in the vehicle, or with access to an
unlocked vehicle. A child’s unsupervised ac-
cess to a vehicle could result in an accident
and/or serious personal injury.
iWhen you switch on the ignition, the indica-
tor and warning lamps (except high beam head-
lamp indicator lamp and turn signal indicator
lamps unless activated) in the instrument cluster
come on. The indicator and warning lamps
(except high beam headlamp indicator lamp and
turn signal indicator lamps if activated) should go
out when the engine is running. This indicates
that the respective systems are operational.


42 Getting started
Unlocking
Ignition (or Position 2)
Press the KEYLESS-GO start/stop but-
ton twice.
This supplies power for all electrical
consumers.
All lamps (except high beam headlamp
indicator lamp and turn signal indicator
lamps unless activated) in the instru-
ment cluster come on. If a lamp in the
instrument cluster fails to come on
when the ignition is switched on, have
it checked and replaced if necessary.
If a lamp in the instrument cluster
remains on after starting the engine
or comes on while driving, refer to
“Lamps in the instrument cluster”
(
page 342).For more information, see “SmartKey with
KEYLESS-GO*” (
page 108).
For information on starting the engine
using the KEYLESS-GO start/stop button,
see “Starting with KEYLESS-GO*”
(
page 54).
iIf you now press the KEYLESS-GO
start/stop button once, the power supply is
again switched off.
iWhen you switch on the ignition, the indica-
tor and warning lamps (except high beam head-
lamp indicator lamp and turn signal indicator
lamps unless activated) in the instrument cluster
come on. The indicator and warning lamps
(except high beam headlamp indicator lamp and
turn signal indicator lamps if activated) should go
out when the engine is running. This indicates
that the respective systems are operational.

57 Getting started
Driving
Switching on headlamps
Low beam headlamps
The exterior lamp switch is located on the
dashboard to the left of the steering wheel.
Exterior lamp switch
1Off
2Low beam headlamps on
Turn the exterior lamp switch to
position B.
The low beam headlamps come on.High beam
The combination switch is located on the
left of the steering column.
Combination switch
1High beam
2High beam flasher
Push the combination switch in
direction of arrow 1.
The high beam headlamps and the high
beam headlamp indicator lamp A in
the instrument cluster come on
(
page 29).
For more information on headlamps, see
“Lighting” (
page 131).
Turn signals
The combination switch is located on the
left of the steering column.
Combination switch
1Turn signals, right
2Turn signals, left
Press the combination switch in
direction of arrow1 or2.
The corresponding turn signal indicator
lampLorKin the instrument
cluster flashes (
page 26).

131 Controls in detail
Lighting
Lighting
For information on how to switch on the
headlamps and use the turn signals, see
“Switching on headlamps” (
page 57)
and “Turn signals” (
page 57).
Exterior lamp switch
Exterior lamp switch
iIf you drive in countries where vehicles drive
on the other side of the road than the country in
which the vehicle is registered, you must have
the headlamps modified for symmetrical low
beams. Relevant information can be obtained at
any authorized Mercedes-Benz Center.
1‚Standing lamps, left
(turn left two stops)
2ˆStanding lamps, right
(turn left one stop)
3MOff
Daytime running lamp mode
(
page 133)
4UAutomatic headlamp mode
Daytime running lamp mode
(
page 133)
5CParking lamps (also side marker
lamps, tail lamps, license plate
lamps, instrument panel lamps)
6BLow beam headlamps or high
beam headlamps.
7‡Front fog lamps
8†Rear fog lamp
iIf you hear a warning signal, you have forgot-
ten to switch off the low beam headlamps or the
parking lamps before opening the driver’s door.
In addition, the message
Lights Are Still
On
appears in the multifunction display.
Switch off the low beam headlamps or the park-
ing lamps.
If the message
Switch off lights or
remove key.
appears in the multifunction
display, remove the SmartKey from the starter
switch or switch off the automatic headlamp
mode.
!Failure to switch off the exterior lamps when
leaving the vehicle may result in a discharged
battery.

132 Controls in detail
Lighting
Low beam headlamps
The low beam headlamps can be switched
on and off with the exterior lamp switch
using the manual headlamp mode.
Turn the exterior lamp switch to
positionB.
The following lamps switch on:

Low beam headlamps

Tail and parking lamps

License plate lamps

Side marker lamps
Automatic headlamp mode
The following lamps switch on and off
automatically depending on the brightness
of the ambient light:

Low beam headlamps

Tail and parking lamps

License plate lamps

Side marker lamps
Turn the exterior lamp switch to
position U.
With the SmartKey in starter switch
position1 or the KEYLESS-GO
start/stop button pressed once, the
tail and parking lamps, the license
plate lamps, and the side marker lamps
will switch on and off depending on the
brightness of the ambient light.
When the engine is running, the low
beam headlamps, the tail and parking
lamps, the license plate lamps, and the
side marker lamps will switch on and
off depending on the brightness of the
ambient light.
Warning!G
If the exterior lamp switch is set toU,
the headlamps will not be automatically
switched on under foggy conditions.
To minimize risk to you and to others,
activate headlamps by turning exterior lamp
switch to B when driving or when traffic
and/or ambient lighting conditions require
you to do so.
In low ambient lighting conditions, only
switch from position U to B with the
vehicle at a standstill in a safe location.
Switching from U to B will briefly
switch off the headlamps. Doing so while
driving in low ambient lighting conditions
may result in an accident.
The automatic headlamp feature is only an
aid to the driver. The driver is responsible for
the operation of the vehicle’s lights at all
times.
iCanada only:
High beam headlamps are only available with the
exterior lamp switch in position B.

133 Controls in detail
Lighting
Daytime running lamp mode
In Canada the daytime running lamp mode
is mandatory and therefore in a constant
mode.
In the USA the daytime running lamp mode
is deactivated by default. Activate the day-
time running lamp mode using the control
system, see “Setting daytime running lamp
mode (USA only)” (
page 163).
Turn the exterior lamp switch to
positionM orU.
When the engine is running, the low
beam headlamps are switched on.
In low ambient light conditions,
the following lamps will switch on
additionally:

Tail and parking lamps

Side marker lamps

License plate lampsCanada only:
When the engine is running and you shift
from a driving position to positionN orP
with the vehicle at a standstill, the low
beam headlamps will switch off with a
delay of 3 minutes.When the engine is running and you

turn the exterior lamp switch to
positionC, the low beam head-
lamps, the tail and parking lamps, the
license plate and the side marker
lamps switch on.

turn the exterior lamp switch to
position B, the manual headlamp
mode has priority over the daytime
running lamp mode
The corresponding exterior lamps
switch on (
page 131).
iWith the daytime running lamp mode activat-
ed and the engine running, the low beam head-
lamps cannot be switched off manually.
iWith the exterior lamp switch in
positionM or U, you cannot switch on the
high beam headlamps.
The high beam flasher is available at all times.
For nighttime driving you should turn the exterior
lamp switch to position B to permit activation
of the high beam headlamps.