2008 MERCEDES-BENZ S-Class steering wheel

405 Controls in detail
Lighting
Switching off the corner-illuminating
lamps
The combination switch for the turn signal
resets automatically after major steering
wheel movements. This will switch off the
corner-illuminating lamps if they were acti-
vated by switching on the left or right turn
signal.
If the turn signal should stay on after mak-
ing the turn, the turn signal and corner-illu-
minating lamp can be switched off by
returning the combination switch to its
original position.
Hazard warning flasher
The hazard warning flasher can be
switched on at all times, even with the
SmartKey removed from the starter switch
or with the SmartKey with KEYLESS-GO*
removed from the vehicle.
The hazard warning flasher is automatical-
ly switched on if

an air bag has been triggered


S 600 and S 65 AMG, USA only: you
brake the vehicle strongly at a speed of
more than 50 mph (70 km/h) and
bring it to a complete stop
1Hazard warning flasher switch

Switching on: Press hazard warning
flasher switch.
All turn signals will flash.

Switching off: Press hazard warning
flasher switch again.
i
If you are driving faster than 25 mph
(40 km/h) when activating the turn signal indica-
tor, the corner-illuminating lamp function is
switched off.
i
The corner-illuminating lamp may remain lit
for a short time. The corner-illuminating lamp
lights up for no more than 20 seconds with the
vehicle standing still. It is then switched off even
if the turn signal is still switched on or you have
turned the steering wheel to full lock.
i
With the hazard warning flasher activated
and the combination switch set for either left or
right turn, only the respective left or right turn
signals will operate when the SmartKey in the
starter switch is in position1 or2 or the
KEYLESS-GO* start/stop button (
page 372) is
pressed once or twice.
i
If the hazard warning flasher was activated
automatically, also press hazard warning flasher
switch 1 to switch off the hazard warning flash-
er.

420 Controls in detailDriving and parkingFor more information, see “Driving instruc-
tions” (
page 559).
Turn signalsCombination switch1Turn signals, right
2Turn signals, left
Press the combination switch in the
direction of arrow1 or2.
The corresponding turn signal indicator
lampL orK in the instrument
cluster flashes (
page 28).
The combination switch resets automati-
cally after major steering wheel move-
ments.
Problems while driving
The engine runs erratically and misfires

An ignition cable may be damaged.


The engine electronics may not be op-
erating properly.


Unburned gasoline may have entered
the catalytic converter and damaged it.

Give very little gas.

Have the problem repaired by an au-
thorized Mercedes-Benz Center as
soon as possible.
!
Shift the automatic transmission to park
positionP or reverse gearR only when the vehi-
cle is stopped in order to avoid damaging the
transmission.
!
Do not run cold engine at high engine
speeds. Running a cold engine at high engine
speeds may shorten the service life of the en-
gine. This is not covered by the Mercedes-Benz
Limited Warranty.
S63AMG and S65AMG only:
At engine temperatures below 68°F (20° C), the
maximum speed is restricted in order to protect
the engine. Avoid driving the vehicle at full speed
while the engine is cold in order to prevent pre-
mature engine wear as well as diminished com-
fort.
!
Simultaneously depressing the accelerator
pedal and applying the brakes reduces engine
performance and causes premature brake and
drivetrain wear which is not covered by the
Mercedes-Benz Limited Warranty.
i
To signal minor directional changes such as
changing lanes, press combination switch only
to point of resistance and release. The corre-
sponding turn signals will flash three times.

424 Controls in detailDriving and parkingAutomatically engaging electronic park-
ing brake* (USA only)
Your vehicle’s electronic parking brake is
automatically engaged when DISTRONIC
Plus* (
page 451) brings your vehicle to a
standstill and at least one of the following
conditions is met:


The engine is switched off.


The driver’s door is opened and the
seat belt is not inserted in the seat belt
buckle.


The hood is released.


The trunk lid is open while reverse
gearR is engaged.


The vehicle is parked for an extended
period of time.
The red indicator lamp 0 (USA only) or
! (Canada only) in the instrument clus-
ter comes on.Emergency braking with electronic
parking brake
In an emergency situation, you can also
brake your vehicle while driving by using
the electronic parking brake.

While driving, press handle for elec-
tronic parking brake (
page 422).
During the braking procedure, the red indi-
cator lamp 0 (USA only) or !
(Canada only) flashes in the instrument
cluster, the message “Please Release Park-
ing Brake” appears on the multifunction
display and you will hear a warning tone.
Once the vehicle comes to a complete stop
the electronic parking brake will engage.
Turning off the engine 
Shift the automatic transmission toP
(page 430).
i
In addition to the electronic parking brake,
park position P can be automatically engaged.
i
Your vehicle will be braked for as long as you
press and hold the switch for the electronic park-
ing brake. The longer you keep the electronic
parking brake pressed, the more strongly your
vehicle will be braked. This method occurs on all
4 wheels, not just the rear wheels.
i
If the engine cannot be turned off as de-
scribed, see “Emergency engine shut-down”
(
page 744).Warning!
G
Do not turn off the engine before the vehicle
has come to a complete stop. With the en-
gine not running, there is no power assis-
tance for the brake and steering systems. In
this case, it is important to keep in mind that
a considerably higher degree of effort is nec-
essary to brake and steer the vehicle.!
Observe instructions


when taking the vehicle through an
automatic conveyor type car wash
(page 618)


when towing the vehicle (
page 737)

429 Controls in detail
Automatic transmission
Shifting from D or R to N
If you want to select neutral positionN
with the transmission being in drive
positionD or reverse gearR:
With the vehicle at a standstill, depress
the brake pedal and keep it pressed.

Press the handle for electronic parking
brake (
page 422).

Move gear selector lever up to resis-
tance point when in drive positionD or
down to resistance point when in
reverse gear R to select neutral
positionN.

Release the brake pedal.
Shifting procedure
The automatic transmission selects indi-
vidual gears automatically, depending on:

drive positionD(
page 430) with
gear ranges (
page 435)


the selected program mode:
(C/S) (
page 436)
or
(M/C/S) (S 63 AMG and S 65 AMG
only) (
page 440)


the position of the accelerator pedal
(page 433)


the vehicle speedWith drive positionD selected, you can use
the steering wheel gearshift control
buttons (
page 438) or gearshift control
paddles (page 438) to influence trans-
mission shifting by:


limiting the gear range


changing gears manually
i
When the vehicle needs to be moved with
the engine switched off and the transmission set
to neutral positionN (
page 430), do not press
the handle for electronic parking brake.
!
Allow engine to warm up under low load use.
Do not place full load on the engine until the op-
erating temperature has been reached.
Shift into reverse gearR or park positionP only
when the vehicle is stopped.
Avoid spinning of a drive wheel for an extended
period when driving off on slippery road
surfaces. This may cause serious damage to the
drivetrain which is not covered by the
Mercedes-Benz Limited Warranty.

435 Controls in detail
Automatic transmission
The hill start assist system is inactive

when starting off on a level road or
downhill grades


with the transmission in neutral
position N


with the electronic parking brake set


if the ESP
® has switched off due to a
malfunction
Gear ranges
With the automatic transmission in drive
positionD and driving in program mode C
or S (
page 436), you can select a gear
range for the automatic transmission to
operate within.
You can limit the gear range by pressing
the left gearshift button or pulling the left
gearshift paddle on the steering wheel
gearshift control, and reverse the gear
range limit by pressing the right gearshift
button or pulling the right gearshift paddle
on the steering wheel gearshift control
(
page 438).The selected gear range appears in the
multifunction display.
1Current gear range
Effect
ï
The transmission shifts through
sixth gear only (applies to
vehicles with 7-speed automatic
transmission only).
î
The transmission shifts through
fifth gear only (applies to
vehicles with 7-speed automatic
transmission only).
é
The transmission shifts through
fourth gear only.

438 Controls in detailAutomatic transmissionSteering wheel gearshift control
With drive positionD selected and driving
in program modeC orS, you can limit or
extend the gear range.
If your vehicle is equipped with manual
shift program M, you can use the steering
wheel gearshift control to manually shift
the gears.
Gearshift control buttons1Left shift button: limiting gear range
2Right shift button: extending gear
range
Gearshift control paddles (S 63 AMG and
S65AMGonly)1Left shift paddle: limiting gear range or
downshift (in program modeM)
2Right shift paddle: extending gear
range or upshift (in program modeM)
The following instructions describe opera-
tion of the steering wheel gearshift control
when driving in program modeC orS.
i
S63AMG and S65AMG only:
For information on using the steering wheel gear-
shift control in program mode M, see “Manual
shift program (S 63 AMG and S 65 AMG only)”
(
page 440).
!
Allow engine to warm up under low load use.
Do not place full load on the engine until the op-
erating temperature has been reached.
Shift into reverse gearR or park positionP only
when the vehicle is stopped.
Avoid spinning of a drive wheel for an extended
period when driving off on slippery road
surfaces. This may cause serious damage to the
drivetrain which is not covered by the
Mercedes-Benz Limited Warranty.
i
You cannot shift with the steering wheel
gearshift control buttons or paddles when the
transmission in park positionP, neutral
positionN or reverse gearR.

440 Controls in detailAutomatic transmissionShifting into optimal gear range
Press and hold left shift button1 or
pull and hold left shift paddle1.
The transmission will automatically
select the gear range suited for optimal
acceleration and deceleration. This will
involve shifting down one or more
gears.Manual shift program (S 63 AMG and
S65AMGonly)
In addition to the automatic shift
programC orS, your vehicle is equipped
with the manual shift programM.
Manual shift programM differs with regard
to spontaneity, response time, and shifting
smoothness from automatic shift
programS.
In the manual program modeM,
system-controlled automatic gearshifting
is switched off and you need to change the
gears by manually upshifting or downshift-
ing using the steering wheel gearshift con-
trol paddles to the left and right of the
steering wheel (
page 438).
Program mode selector switchM Manual For manual gear shifting
C Comfort For standard driving
S Sport For sporty driving!
Allow engine to warm up under low load use.
Do not place full load on the engine until the op-
erating temperature has been reached.
Shift into reverse gearR or park positionP only
when the vehicle is stopped.
Avoid spinning of a drive wheel for an extended
period when driving off on slippery road
surfaces. This may cause serious damage to the
drivetrain which is not covered by the
Mercedes-Benz Limited Warranty.

441 Controls in detail
Automatic transmission
The selected program mode appears in the
multifunction display (
page 437).Activating manual shift program

Press the program mode selector
switch repeatedly until the “M” for
manual program modeM appears in
the multifunction display.
The transmission switches to the
manual program modeM. Automatic
shifting is switched off. The gear range
is not limited.
You can change the gears manually with
drive positionD selected. You can upshift
or downshift through the gears in succes-
sion.Upshifting

Briefly pull right shift paddle2
(page 438).
The transmission shifts to the next
higher gear.
i
For information on automatic program
modesC orS, see “Automatic shift program”
(
page 436) and “Steering wheel gearshift con-
trol” (page 438).
i
The manual program modeM will not be
stored. When the engine is turned off with the
manual program modeM selected, the transmis-
sion will go to the automatic program mode
(CorS) when the engine is restarted.
!
In the manual program modeM, the trans-
mission will not upshift, even if the engine has
reached its overrevving range. Shift up to the
next gear before the engine has reached its over-
revving range. Make absolutely certain that the
engine speed does not reach the red marking on
the tachometer (
page 28). Otherwise the en-
gine could be damaged which is not covered by
the Mercedes-Benz Limited Warranty.