2008 MERCEDES-BENZ S-Class ESP

411 Controls in detail
Power windows

Switch on the ignition (
page 370).

Opening: Press the lower part of
switch1 to 4 (
page 410) to the re-
sistance point.
The corresponding window will move
downwards until you release the
switch.

Closing: Press the upper part of
switch1 to 4 (
page 410) to the re-
sistance point.
The corresponding window will move
upwards until you release the switch.
If the window encounters an obstruction
that blocks its path in a circumstance where
you are closing the window by pressing and
holding the switch, by pressing and holding
button ‹ on the SmartKey or SmartKey
with KEYLESS-GO*, by pressing and holding
the sensor surface (vehicles with
KEYLESS-GO*) on an outside door handle,
or by pressing and holding button, on
the climate control panel, the automatic re-
versal function will not operate.
When leaving the vehicle, always remove the
SmartKey or SmartKey with KEYLESS-GO*
from the starter switch, take it with you, and
lock the vehicle. Do not leave children unat-
tended in the vehicle, or with access to an
unlocked vehicle. A child’s unsupervised ac-
cess to a vehicle could result in an accident
and/or serious personal injury.
i
You can also open or close the windows us-
ing the SmartKey, see “Summer opening fea-
ture” (page 412) and “Convenience closing
feature” (page 413).
Depending on current position, the windows may
also open or close when the air recirculation
button, (page 501) is pressed and held
for 2 seconds.
i
Operating the windows from the rear is not
possible if you activate the override switch
(
page 64).
i
If PRE-SAFE
® has been activated, the door
windows close automatically until only a small
gap remains.
i
With the SmartKey in starter switch
position0 or removed from the starter switch,
the power windows can be operated:


until you open the driver’s or front passenger
door


for at least 5 minutes if no door was opened
Warning!
G
If you press and hold the switch up when
closing the window, and upward movement
of the window is blocked by some obstruc-
tion including but not limited to arms, hands,
fingers, etc., the automatic reversal will not
operate.


412 Controls in detailPower windows
Express-opening: Press the lower part
of switch1 to4 (
page 410) past
the resistance point and release.
The corresponding window opens com-
pletely.

Express-closing: Press the upper part
of switch1 to4 (
page 410) past
the resistance point and release.
The corresponding window closes com-
pletely.

Stopping during Express-operation:
Briefly press the respective power win-
dow switch again.
Rear side window sunshades*
Closing: With the side window fully
closed, press the upper part of
switch3 or4 (
page 410).
The rear side window sunshade will be
fully closed.

Opening: Press the lower part of
switch3 or4 (
page 410).
The rear side window sunshade will be
fully opened.
Summer opening feature
If the weather is warm, you can ventilate
the vehicle before driving off by simulta-
neously:

opening the door windows and rear
side window sunshades*


opening the tilt/sliding sunroof or
tilt/sliding panel* and extending the
roller sunblinds*


turning on the seat ventilation* for the
driver’s seat
Warning!
G
Driver’s door only:
If within 5 seconds you again press the
switch past the resistance point and re-
lease, the automatic reversal will not oper-
ate.
!
If the upward movement of the window is
blocked during the closing procedure, the win-
dow will stop and open slightly. Remove the ob-
struction, press the respective power window
switch at the upper part again past the resis-
tance point and release. If the window still does
not close when there is no obstruction, press
and hold the respective power window switch at
the upper part. The side window will then close
without the obstruction sensor function.
i
The rear side window sunshade cannot be
partially closed.
i
The switches on the rear doors can also be
used to close the rear side window sunshades on
the other side of the vehicle.
i
The switches on the driver’s door take pre-
cedence over the rocker switches on the other
doors.


418 Controls in detailDriving and parking
Press KEYLESS-GO start/stop button
once.
The engine starts if the SmartKey with
KEYLESS-GO is in the vehicle.
For information on turning off the engine
with KEYLESS-GO, see “Turning off the en-
gine” (
page 424).Starting difficulties
The engine does not start. You can hear
the starter.
There could be a malfunction


in the engine electronics, or


in the fuel supply system
Carry out the following steps:

If you are starting the engine with the
SmartKey: Turn SmartKey in starter
switch to position0 and repeat starting
procedure (
page 416).

If you are starting the engine with
KEYLESS-GO*: Close any doors that
may be open to allow for better detec-
tion of the SmartKey with
KEYLESS-GO*.
or

Remove the KEYLESS-GO* start/stop
button from starter switch.

Start the engine with the SmartKey as
radio signals from another source may
be interfering with the SmartKey with
KEYLESS-GO*.

Repeat the starting procedure
(page 416).
If the engine does not start after several
starting attempts:

Contact an authorized Mercedes-Benz
Center or call Roadside Assistance.
The engine does not start. You cannot
hear the starter.
The battery may not be sufficiently
charged.

Have the vehicle jump-started
(page 734).
If the engine will not start despite a jump
start:

Contact an authorized Mercedes-Benz
Center or call Roadside Assistance.
i
You can also start the engine with the auto-
matic transmission set to neutral positionN.
i
If you wish to start the vehicle with the
SmartKey instead of the KEYLESS-GO feature,
remove the KEYLESS-GO start/stop button from
the starter switch and proceed as described in
“Starting with the SmartKey” (
page 417).
!
Remember that extended starting attempts
can drain the battery.


420 Controls in detailDriving and parkingFor more information, see “Driving instruc-
tions” (
page 559).
Turn signalsCombination switch1Turn signals, right
2Turn signals, left
Press the combination switch in the
direction of arrow1 or2.
The corresponding turn signal indicator
lampL orK in the instrument
cluster flashes (
page 28).
The combination switch resets automati-
cally after major steering wheel move-
ments.
Problems while driving
The engine runs erratically and misfires

An ignition cable may be damaged.


The engine electronics may not be op-
erating properly.


Unburned gasoline may have entered
the catalytic converter and damaged it.

Give very little gas.

Have the problem repaired by an au-
thorized Mercedes-Benz Center as
soon as possible.
!
Shift the automatic transmission to park
positionP or reverse gearR only when the vehi-
cle is stopped in order to avoid damaging the
transmission.
!
Do not run cold engine at high engine
speeds. Running a cold engine at high engine
speeds may shorten the service life of the en-
gine. This is not covered by the Mercedes-Benz
Limited Warranty.
S63AMG and S65AMG only:
At engine temperatures below 68°F (20° C), the
maximum speed is restricted in order to protect
the engine. Avoid driving the vehicle at full speed
while the engine is cold in order to prevent pre-
mature engine wear as well as diminished com-
fort.
!
Simultaneously depressing the accelerator
pedal and applying the brakes reduces engine
performance and causes premature brake and
drivetrain wear which is not covered by the
Mercedes-Benz Limited Warranty.
i
To signal minor directional changes such as
changing lanes, press combination switch only
to point of resistance and release. The corre-
sponding turn signals will flash three times.

431 Controls in detail
Automatic transmission
!
DISTRONIC Plus*:
The transmission will shift to park positionP
automatically, only when DISTRONIC Plus brings
your vehicle to a standstill, and when it meets at
least one of the following conditions at the same
time:


The engine is turned off.


The driver’s or passenger door opens and
the seat belt is not engaged in the buckle.


The hood is released.


The trunk lid is open while reverse gearR is
engaged.


The vehicle is parked for an extended period
of time.
In addition to shifting to park positionP, the
electronic parking brake will be engaged auto-
matically.
i
Make it a practice to always shift into park
positionP before turning off the engine and


remove the SmartKey from the starter
switch
or


open a front door
or when using KEYLESS-GO*, before turning off
the engine with the start/stop button and open-
ing a front door.
Effect
í
Reverse gear
Shift into reverse gearR only
when the vehicle is stopped.
ë
Neutral
No power is transmitted from the
engine to the drive axle. When
the brakes are released, the
vehicle can be moved freely
(pushed or towed).
To avoid damage to the trans-
mission, never shift into neutral
positionN while driving.
If the ESP
® is deactivated or
malfunctioning:
Shift into neutral positionN only
if the vehicle is in danger of
skidding, e.g. on icy roads.
Effect

435 Controls in detail
Automatic transmission
The hill start assist system is inactive

when starting off on a level road or
downhill grades


with the transmission in neutral
position N


with the electronic parking brake set


if the ESP
® has switched off due to a
malfunction
Gear ranges
With the automatic transmission in drive
positionD and driving in program mode C
or S (
page 436), you can select a gear
range for the automatic transmission to
operate within.
You can limit the gear range by pressing
the left gearshift button or pulling the left
gearshift paddle on the steering wheel
gearshift control, and reverse the gear
range limit by pressing the right gearshift
button or pulling the right gearshift paddle
on the steering wheel gearshift control
(
page 438).The selected gear range appears in the
multifunction display.
1Current gear range
Effect
ï
The transmission shifts through
sixth gear only (applies to
vehicles with 7-speed automatic
transmission only).
î
The transmission shifts through
fifth gear only (applies to
vehicles with 7-speed automatic
transmission only).
é
The transmission shifts through
fourth gear only.

440 Controls in detailAutomatic transmissionShifting into optimal gear range
Press and hold left shift button1 or
pull and hold left shift paddle1.
The transmission will automatically
select the gear range suited for optimal
acceleration and deceleration. This will
involve shifting down one or more
gears.Manual shift program (S 63 AMG and
S65AMGonly)
In addition to the automatic shift
programC orS, your vehicle is equipped
with the manual shift programM.
Manual shift programM differs with regard
to spontaneity, response time, and shifting
smoothness from automatic shift
programS.
In the manual program modeM,
system-controlled automatic gearshifting
is switched off and you need to change the
gears by manually upshifting or downshift-
ing using the steering wheel gearshift con-
trol paddles to the left and right of the
steering wheel (
page 438).
Program mode selector switchM Manual For manual gear shifting
C Comfort For standard driving
S Sport For sporty driving!
Allow engine to warm up under low load use.
Do not place full load on the engine until the op-
erating temperature has been reached.
Shift into reverse gearR or park positionP only
when the vehicle is stopped.
Avoid spinning of a drive wheel for an extended
period when driving off on slippery road
surfaces. This may cause serious damage to the
drivetrain which is not covered by the
Mercedes-Benz Limited Warranty.

445 Controls in detail
Instrument cluster
Tachometer
The red marking on the tachometer de-
notes excessive engine speed.To help protect the engine, the fuel supply
is interrupted if the engine is operated
within the red marking.
Outside temperature indicator
The outside temperature indicator is on
the bottom left-hand side of the instru-
ment cluster (
page 28).
The temperature sensor is located in the
front bumper area. Due to its location, the
sensor can be affected by road or engine
heat during idling or slow driving. There-
fore, the accuracy of the displayed temper-ature can only be verified by comparison to
a thermometer placed next to the sensor,
not by comparison to external displays
(e.g. bank signs, etc.).
When moving the vehicle into colder ambi-
ent temperatures (e.g. when leaving your
garage), you will notice a delay before the
lower temperature is displayed.
A delay also occurs when ambient temper-
atures rise. This prevents inaccurate tem-
perature indications caused by heat
radiated from the engine during idling or
slow driving.
Fuel gauge
The fuel gauge is on the left-hand side of
the instrument cluster (
page 28). Once
the fuel level has fallen below the reserve
mark, the yellow segment indicator for the
fuel reserve comes on.
of the vehicle and do not stand near the ve-
hicle until the engine has cooled down.!
Excessive coolant temperature triggers a
warning in the multifunction display
(
page 680).
The engine should not be operated with the cool-
ant temperature above 248°F (120°C), i.e. in
the red zone of the coolant temperature gauge.
Doing so may cause serious engine damage
which is not covered by the Mercedes-Benz Lim-
ited Warranty.
i
During severe operating conditions,
e.g. stop-and-go traffic, the coolant temperature
may rise close to 248°F (120°C), i.e. close to
the red zone of the temperature gauge.
!
Avoid driving at excessive engine speeds, as
it may result in serious engine damage that is not
covered by the Mercedes-Benz Limited
Warranty.
Warning!
G
The outside temperature indicator is not de-
s i g n e d t o s e r v e a s a n i c e - w a r n i n g d e v i c e a n d
is therefore unsuitable for that purpose.
Indicated temperatures just above the freez-
ing point do not guarantee that the road sur-
face is free of ice. The road may still be icy,
especially in wooded areas or on bridges.