2008 MERCEDES-BENZ S-Class display

197 Control systems
COMAND navigation (introduction)
1Crosshair
2Details of the crosshair position
3Map scaleAdjusting the map scale

Rotate ymz.
Rotating clockwise zooms in, rotating
counterclockwise zooms out.
Saving crosshair position as destination
in last destinations list

Showing menu system, if neces-
sary: Press n.

Saving: Select “Position”
“Save Po-
sition”.
COMAND saves the crosshair position
as a destination in the last destinations
list (
page 258).
Hiding the crosshair

Press back button L in the center
console (
page 88).
The crosshair disappears and the map
is centered on the vehicle position.
or

Set the map to the vehicle or destina-
tion position, see the explanation be-
low.
Centering the map on the vehicle or
destination position

Centering on the vehicle’s position:
Select “Navi”
“Position”
“Vehicle
Position Map”.
or

Press back button L when the
crosshair is displayed.

Centering on the destination:
Select “Navi”
“Position”
“Destina-
tion Position Map”.
i
Display 2 may be the name of a road, for
example, provided the digital map contains the
necessary data.
If no data is available, display 2 shows:


the coordinates of the crosshair if the
geo-coordinate display is switched on
(page 200) and the GPS signal is strong
enough


no display if the geo-coordinate display is
switched off (
page 200)
i
If you have moved the map, you can use this
function to rapidly return the map to the position
of the vehicle or destination. It is only possible to
center the map on the destination position when
route guidance is active.

198 Control systemsCOMAND navigation (introduction)Basic settings
Map perspective
COMAND can display the map from a
bird's eye view or in the normal map view.
Select map perspective:
Select “Navi”
“Navi”
“Map Dis-
play”.
The map display list appears. A dot R
indicates the current setting.

Select “Bird’s-eye view”.
The bird's eye view is switched on or
off, depending on the previous status.Map orientation
1Current map orientation
The following may be displayed:


8 = “Heading Up” (the map is dis-
played so that the direction of travel is
always up; the orange point of the icon
points north)


9 = “North Up” (the map view is dis-
played so that north is always up)

Setting map orientation:
Select “Navi”
“Navi”
“Map Dis-
play”.
The map display list appears. A dot R
indicates the current setting.

Select “North Up” or “Heading Up”.

Exiting menu: Slide omp.
The map orientation changes accord-
ingly.
Setting POI symbols
You can set which points of interest (POIs)
should be displayed as symbols in the
map. POIs are garages, hotels, movie the-
aters or restaurants, for example.
The following settings are possible:


“Standard symbols” (symbol deter-
mined by the factory settings)


“Personal symbols” (you can determine
the symbols yourself)


“No symbols”
i
You can make the following settings regard-
less of whether route guidance is active or inac-
tive.
i
If you scroll the map in the bird's eye view,
COMAND switches back to the normal map view.
i
Depending on the map scale on the map,
POI symbols may not be visible on the map al-
though their display is activated. In addition, POI
symbols may be covered by the map’s labels.

199 Control systems
COMAND navigation (introduction)

Adjusting: Select “Navi”
“Navi”

“Map Display”.
The map display list appears. A dot R
indicates the current setting.

Select “Standard symbols”, “Personal
symbols” or “No symbols”.
If you select “Personal symbols”, the
list of POIs appears.
Switching POI symbol display on
or off: Select the desired POI.
The corresponding symbol displays
are switched on or off, depending
on the previous status. A check-
mark indicates which status is ac-
tive. You can switch on the symbol
displays for more than one POI.

Exiting menu: Slide omp or press
back button L in the center console
(page 88).
Arrival time and distance
You can set whether the estimated arrival
time and the distance to the destination
should be displayed in the map.

Displaying: Select “Navi”
“Navi”

“Map Display”.
The map display list appears. A dot R
indicates the current setting.

Select “Arrival Time/Distance”.
Depending on the previous status the
display showing the arrival time and
distance is switched on or off.Current street
You can set whether the current street you
are driving on should be displayed in the
map.

Displaying: Select “Navi”
“Navi”

“Map Display”.
The map display list appears. A dot R
indicates the current setting.

Select “Current Street”.
Depending on the previous status the
display showing the current street is
switched on or off.
i
The list shows all symbols that are contained
in the digital map across all states (USA) and/or
provinces (CDN). Not all POIs in all states (USA)
or in all provinces (CDN) are available, however.
Certain POI symbols may not be displayed on the
map, even if the symbol display is switched on.

200 Control systemsCOMAND navigation (introduction)Geo-coordinate displayIllustration: map with geo-coordinate dis-
play switched on1Current height above sea level
2Number of GPS satellites from which
signals for positioning can be received
3Coordinate displayDisplay options with geo-coordinate dis-
play switched on
If the crosshair is displayed on the map
view (map was moved manually), only dis-
play 3 is visible.
It shows either the coordinates of the
crosshair or other data on the crosshair
position, e.g. a street name. The digital
map must contain relevant data in order
for this other data to be displayed.Switching the geo-coordinate display on
or off

Select “Navi”
“Navi”
“Map Dis-
play”.
The map display list appears.

Select “Coordinates”.
The geo-coordinate display is switched
on or off, depending on the previous
status. A checkmark indicates which
status is active.

Exiting menu: Slide omp or press
back button L in the center console
(page 88).
i
There must be sufficient GPS reception for
displays 1, 2 and 3 to be shown. Height dis-
play 1 is an approximation because the naviga-
tion system uses the GPS signals for the
calculation.
i
If there is no crosshair on the map view, dis-
plays 1, 2 and 3 are visible. Display 3
shows the coordinates of the current vehicle po-
sition.

225 Control systems
COMAND navigation system (entering a destination)
Entering a destination from the list of last destinations
Select “Navi”
“Destination”

“From Last Destinations”.
The list of last destinations appears.
The most recent destination is at the
top of the list.

Select desired destination.

Starting route calculation:
Select “Start”, see also (
page 222).
Entering a destination from the map
Calling up the map
In the address input menu, select
“Map” (
page 202).
You will see the map with a crosshair.
The map is set to the address set in the
address input menu.
or

Select “Navi”
“Destination”

“Via Map”.
You will see the map with a crosshair.1Crosshair
2Details of the crosshair position
3Map scale
i
Depending on the factory settings of the ve-
hicle, it may not be possible to enter a destina-
tion while the vehicle exceeds a preset speed. As
soon as the vehicles speed drops to below the
preset speed, the function is available again.
You can enter a destination via the map if the dig-
ital map does not contain the address of the des-
tination, but the destination must be within the
area of the digital map.
i
Display 2 may be the name of a road, for
example, provided the digital map contains the
necessary data.
If no data is available, display 2 shows:


the coordinates if the geo-coordinate display
is switched on (
page 200)


no display if the geo-coordinate display is
switched off (
page 200)

226 Control systemsCOMAND navigation system (entering a destination)Moving the map and selecting the des-
tination
Moving map: Slide qmr, omp or
wmx.

Adjusting map scale: Rotate ymz.
Rotating clockwise enlarges the map,
rotating counterclockwise reduces it.

Selecting a destination: Press n.
If the crosshair is located off the edge
of the digital map, a route cannot be
calculated to this destination and you
will see the message “The destination is
located off the map.”.

Select “OK”.

Move the map and select a destination
again.
If the destination is within the limits of
the digital map, COMAND attempts to
attribute the destination to the map,
which can take approximately
2 seconds.
If the destination can be attributed, you
will see the address of the destination.
If not, you will see the display “Destina-
tion from map”.

Starting route calculation:
Select “Start”, see also (
page 222).
Entering a stopoveri
When route guidance is active, you can en-
ter a stopover. Stopovers can be predefined des-
tinations from the following predefined
categories:


“Mercedes-Benz Center”


“Hospital”


“Gas station”


“Parking lot”


“Restaurant”
However, you can also enter destinations other
than the predefined ones.
i
You can use the stopover function to influ-
ence the route guidance calculation to the main
destination. When you have reached your stop-
over, COMAND automatically calculates the
route to the main destination.

227 Control systems
COMAND navigation system (entering a destination)
Entering predefined destinations
Select “Navi”
“Destination”

“Stopover”.
If a stopover has already been entered,
you can change it.
Changing: Select “Change Stop-
over”.
You can now select a category.

Selecting a category:
Select category, e.g. “Gas station”.
COMAND first looks for destinations
within the immediate vicinity of the ve-
hicle and near the vehicle’s route. If
there are no destinations available
there, COMAND searches for destina-
tions in an area around the vehicle po-
sition.
If COMAND does not find any destina-
tions, you will see a message to this ef-
fect.

Select “OK”.
You can now select a different
category.
If COMAND finds destinations, you will
see a list of the destinations and details
of how far away they are in the
right-hand side of the display. The in-
formation about how far away the des-
tinations are can take a few seconds to
be displayed.
The left-hand part of the display shows
the destinations on the map. The desti-
nation marked in the list is highlighted
in the map.

Selecting a destination: Select the
desired destination from list.
The address of the destination ap-
pears.

Starting route calculation:
Select “Start”, see also (
page 222).Entering another destination as a stop-
over

Select “Navi”
“Destination”

“Stopover”.

Entering: Select “Other”.
You can select between the following
menu items:

“Address Entry”


“From Memory”


“From Last Destinations”


“From POIs”

Select a menu item.

229 Control systems
COMAND navigation system (Point of interest entry)
COMAND navigation system (Point of interest entry)
Entering a POI in the surrounding area
In the map view while the menu system
is displayed, select “Destination”

“From POIs”
“Current Position”
(page 196).

Continue with designating the POI cat-
egory (
page 230).
Entering a POI in the surroundings of a
given city
Option 1
In the map view while the menu system
is displayed, select “Destination”

“From POIs”
“Other City”
(page 196).

If necessary, enter state (USA)
(page 203) or province (CDN)
(page 203).

Entering town: Select “City”.
The town/city input menu appears.

Then proceed as described in the “En-
tering a city” section (
page 208).

After entering the city, continue with
designating the POI category
(page 230).
Option 2

Enter an address in the address input
menu (
page 202).

Select “POI”.

Continue with designating the POI cat-
egory (
page 230).
Entering a POI in a different region
In the map view while the menu system
is displayed, select “Destination”

“From POIs”
“Global POI”
(page 196).
The category list appears. The state
(USA) or province (CDN) currently se-
lected is shown in the first list entry.
i
This function gives you quick access to POIs
which are of national interest in the state (USA)
or province (CDN) you have selected. The follow-
ing categories may be available:


“AIRPORT”


“BORDER CROSSING”


“HIGHWAY ACCESS”
Not all categories are available in all states (USA)
or provinces (CDN).