2008 MERCEDES-BENZ ML SUV parking brake

Changing the bulbs
314 Bulb Type
1 Third brake
lamp LED
36 2 Brake lamp P 21 W
or
LED*
36 3 Turn signal lamp PY 21 W
or
LED*
36 4 Foglamp/tail
lamp/parking
lamp
or P 21 W
or
Rear fog lamp
Side lamp/park-
ing lamp
W 16 W*
LED*
36 5 Foglamp/tail
lamp/parking
lamp
or P 21 W
or
Rear fog lamp
Side lamp/park-
ing lamp
W 16 W*
LED*
36 Bulb Type
6 Reversing lamp P 21 W
or
W 16 W*
7 Licence plate
lamp C 5 W
Vehicles with an exterior spare wheel bracket*
Bulb Type
1 Third brake
lamp
LED
36 2 Reversing lamp P 21 W
3 Rear fog lamp P 21 W Bulb Type
4 Brake lamp/tail
lamp/parking
lamp P 21 W
5 Turn signal lamp PY 21 W
6 Licence plate
lamp W 5 W
Before changing bulbs
You can replace the following bulbs:
R
Dipped-beam headlamps (vehicles with
halogen headlamps)
R Main-beam headlamps
R Side lamp and parking lamp
R Foglamps with/without cornering light
function*
R Turn signal lamp (front)
R Brake lamp
R Reversing lamp
R Rear foglamp/tail lamp/parking lamp
R Turn signal lamp (rear)
R Licence plate lamp
36 These bulbs must be replaced at a qualified specialist workshop, e.g. a Mercedes-Benz Service Centre. Practical advice
* optional
164_AKB; 5; 5, en-GB
wobuchh,
Version: 2.10.6 2008-05-11T11:55:12+02:00 - Seite 314Dateiname: 6515_4293_02_buchblock.pdf; preflight

Changing the bulbs
319Left-hand stowage compartment
1
Release catch
2 Stowage compartment
X To open the stowage compartment:
insert a suitable object, e.g. a coin, into the
slot of release button 1.
X Turn release button 190°in the direction
of the arrow and remove the stowage com-
partment.
X To close the stowage compartment:
insert the stowage compartment and turn
release button 1in the opposite direction
to the arrow until the slot in the release
button is in a vertical position.
X To close the side trim panel: insert the
side trim panel and turn catch 190° in the
opposite direction to the arrow. Right-hand side trim panel
Right-hand side trim panel
1
Release catch
2 Side trim panel
X To open: insert a suitable object, e.g. a
coin, into the slot of release catch 1on
side trim panel 2.
X Turn release catch 190° in the direction
of the arrow and remove side trim panel
2.
X To close: insert side trim panel 2and turn
catch 190° in the opposite direction to
the arrow. Changing the tail lamps X
Switch off the lights.
X Open the luggage compartment.
X Open the side trim panel (Y page 318). Tail lamps without LEDs*
1
Brake lamp
2 Reversing lamp
3 Rear foglamp (left)/tail lamp/parking
lamp
4 Rear foglamp (left)/tail lamp/parking
lamp
5 Turn signal lamp Practical advice
* optional
164_AKB; 5; 5, en-GB
wobuchh
,V ersion: 2.10.6
2008-05-11T11:55:12+02:00 - Seite 319 ZDateiname: 6515_4293_02_buchblock.pdf; preflight

Changing the bulbs
320Tail lamps with LEDs*
1
Reversing lamp
2 Rear fog lamp
3 Rear fog lamp
X Turn the corresponding bulb holder anti-
clockwise and remove it.
X Take the bulb out of the bulb holder.
X Insert the new bulb into the bulb holder.
X Insert the bulb holder and turn it clockwise.
X Close the side trim panel (Y page 318).Vehicles with an exterior spare wheel
bracket*
On vehicles with an exterior spare wheel
bracket*, the following lamps are located in
the bumper:
R
Tail lamp
R Parking lamp
R Brake lamp
R Turn signal lamp
R Licence plate lamp Bumper
1
Lamp cluster
X Switch off the lights.
X Insert a plastic card into the gap between
the bumper and lamp cluster 1.X
Push the plastic card in the direction of the
arrow.
Lamp cluster 1pops out.
X Remove lamp cluster 1. Lamp cluster
1
Bulb holder for turn signal lamp
2 Bulb holder for tail lamp/parking lamp/
brake lamp
X Turn the corresponding bulb holder anti-
clockwise and remove it.
X Lightly press the bulb into the bulb holder,
turn it anti-clockwise and remove it from
the bulb holder.
X Insert the new bulb into the bulb holder and
turn it clockwise. Practical advice
* optional
164_AKB; 5; 5, en-GB
wobuchh,
Version: 2.10.6 2008-05-11T11:55:12+02:00 - Seite 320Dateiname: 6515_4293_02_buchblock.pdf; preflight

Flat tyre
323Flat tyre
Flat tyre equipment variants
Your vehicle may be equipped with:
R a TIREFIT kit (Y page 255)
R a "Minispare" emergency spare
wheel* (Y page 256)
R a collapsible emergency spare
wheel* (Y page 258)
R a spare wheel* (Y page 256)
R the MOExtended run-flat sys-
tem* (Y page 333) Preparing the vehicle
i Vehicle preparation is not necessary on
vehicles with MOE tyres*.
X Make sure that highway level* is selec-
ted 37
(Y page 158).
X Stop your vehicle as far away from traffic
as possible on solid, non-slippery, level
ground.
X Switch on the hazard warning lamps. X
Firmly depress the parking brake.
X Move the selector lever to P.
X All occupants must get out of the vehicle.
Make sure that they are not endangered as
they do so.
X Make sure that no one is near the danger
area whilst a wheel is being changed. Any-
one who is not directly assisting in the
wheel change should, for example, stand
behind the barrier.
X Switch off the engine.
Vehicles without KEYLESS GO* X
Remove the key from the ignition lock.
Vehicles with KEYLESS GO* X
Open the driver's door.
The on-board electronics have status 0,
which is the same as the key having been
removed.
X Vehicles with the AIRMATIC package* and
the Off-Road Pro engineering package*:
Remove the KEYLESS GO button from the
ignition lock. For all vehicles X
Get out of the vehicle.
X Close the driver's door.
X Place the warning triangle ( Ypage 254) at
a suitable distance. Observe legal require-
ments.
i To operate the electric air-pump, you can
use the power socket in the luggage com-
partment (Y page 205) or rear compart-
ment (Y page 205), even when the ignition
is switched off. For example, to use TIREFIT
or to inflate the collapsible emergency
spare wheel*.
An emergency cut-off ensures that the on-
board voltage does not drop too low. If the
on-board voltage is too low, power to the
sockets is automatically cut-off. This
ensures that there is sufficient power to
start the engine.
37 Not on steel-sprung vehicles. Practical advice
* optional
164_AKB; 5; 5, en-GB
wobuchh,
Version: 2.10.6 2008-05-11T11:55:12+02:00 - Seite 323 ZDateiname: 6515_4293_02_buchblock.pdf; preflight

Battery
335step out of the vehicle first and touch the
bodywork.
R Do not wipe the battery using a cloth. The
battery may explode as a result of elec-
trostatic charge or due to flying sparks.
! Switch off the engine and remove the
key/KEYLESS GO * button before loosen-
ing or removing the battery terminal
clamps. You may otherwise destroy elec-
tronic components such as the alternator.
i Mercedes-Benz recommends that you
have all work involving the battery, e.g.
removing, charging and replacing, carried
out at a qualified specialist workshop, e.g.
a Mercedes-Benz Service Centre.
The battery is located under the front seat on
the right-hand side when viewed in the direc-
tion of travel. Disconnecting the battery
G
Risk of accident
If the battery is disconnected:
R the brake boosting effect will not be avail-
able. Greater braking force will then be
required and the brake pedal travel will
be longer. If necessary, depress the
brake pedal with maximum force.
R you can no longer turn the key in the igni-
tion and, on vehicles with KEYLESS
GO*, pressing the KEYLESS GO button*
will have no effect
R the selector lever is locked in position P
! Always disconnect the battery in
the order described below. Never swap the
terminal clamps. You may otherwise dam-
age the vehicle electronics.
X Firmly depress the parking brake and shift
the selector lever to position Pon vehicles
with automatic transmission.
X Position the front seat as far forwards as
possible.
X Switch off all electrical consumers. 1
Battery cover
X Get into the rear compartment.
X Remove battery cover 1from under the
right-hand front seat. 2
Carpet Practical advice
* optional
164_AKB; 5; 5, en-GB
wobuchh
,V ersion: 2.10.6
2008-05-11T11:55:12+02:00 - Seite 335 ZDateiname: 6515_4293_02_buchblock.pdf; preflight

Jump-starting
339Jump-starting
If your vehicle's battery is discharged, the
engine can be jump-started from another
vehicle or from an external battery using jump
leads.
Observe the following points:
R Jump-starting may only be performed when
the engine and catalytic converter are cold.
R Do not start the engine if the battery is fro-
zen. Let the battery thaw first.
R Jump-starting may only be performed from
batteries with a nominal voltage of 12 V.
R Only use jump leads which are protected
against polarity reversal and which have a
sufficient cross-section and insulated ter-
minal clamps.
i Jump leads which are protected against
polarity reversal and further information
about jump-starting can be obtained from
any Mercedes-Benz Service Centre.
! Avoid repeated and lengthy starting
attempts.
Never start the vehicle using a rapid battery
charger. G
Risk of injury
There is a risk of acid burns when jump-
starting a vehicle due to the gases which
escape from the battery. Do not lean over
the battery while the engine is being jump-
started. G
Risk of explosion
Gases escaping from the battery during
jump-starting may cause minor explosions.
Avoid creating sparks. Keep naked flames
away from the battery, and do not smoke.
Comply with safety precautions and take
protective measures when handling batter-
ies. You will find these under "Battery" in
the index.
X Make sure that the two vehicles do not
touch.
X Depress the parking brake firmly.
X Move the selector lever to P.
X Switch off all electrical consumers. 1
Positive terminal on your vehicle
2 Earth point on your vehicle
3 Positive terminal of donor battery
4 Negative terminal of donor battery
X Connect positive terminal 1on your vehi-
cle to positive terminal 3of the donor
battery using the jump lead, beginning with
your own battery.
X Start the engine of the donor vehicle and
run it at idling speed.
X Connect negative terminal 4of the donor
battery to the earth point 2of your vehicle
using the jump lead, connecting the jump
lead to the donor battery first.
X Start the engine. Practical advice
164_AKB; 5; 5, en-GB
wobuchh,
Version: 2.10.6 2008-05-11T11:55:12+02:00 - Seite 339 ZDateiname: 6515_4293_02_buchblock.pdf; preflight