2008 MERCEDES-BENZ GL320 lock
[x] Cancel search: lockPage 133 of 601
132 Controls in detail
Seats
Return seat into its original position
(
page 132).
The message in the multifunction dis-
play disappears.
For setting the front passenger seat back
into the stored position, see “Recalling po-
sitions from memory” (
page 142).
For information on how to fold down the
second-row seats completely, see “Folding
second-row seats” (
page 306).
Returning second-row seats to their
original positionFold seat (page 131) back until it au-
dibly engages.
Fold seat backrest (page 130) back
into original position until it engages.
To make sure the seat backrest has en-
gaged, lean firmly against the backrest.Emergency exit for third-row seats
1Emergency release
2Seat backrest
Warning!G
When occupants have entered or exited the
vehicle using the easy-entry/exit feature,
before driving off make sure
the seats are properly locked
the seat backrests are in an upright po-
sition and are properly locked
If a seat and seat backrest are not properly
locked, the seat could move forward and the
seat backrest could fold. You could slide un-
der the seat belt during braking, vehicle ma-
neuvers, or in an accident. If you slide under
it, the belt would apply force at the abdomen
or neck. That could cause serious or even fa-
tal injuries.
iIf, due to an accident or other situation, it is
not possible for you to exit the vehicle on the
side of the easy-entry seat (
page 130), you
can fold the left side of the seat backrest in the
second row of seats down in order to open the
left rear door.
!Make sure that the head restraint is pushed
all the way down (
page 135).
164.boo Seite 132 Freitag, 30. März 2007 12:54 12
Page 135 of 601
134 Controls in detail
Seats
Rear seat adjustment
Seat backrest tilt (second-row seats)The seat backrest tilt can be set to five
different positions.
The handles for adjusting the seats are
located on the rear of each seat base.
1Adjustment handle
While seated, pull handle1 in direc-
tion of arrow to resistance point and
hold it there.
To move seat backrest back, lean light-
ly against backrest.
Warning!G
Never ride in a moving vehicle with the seat
backrest in an excessively reclined position
as this can be dangerous. You could slide
under the seat belt in a collision. If you slide
under it, the belt would apply force at the ab-
domen or neck. That could cause serious or
fatal injuries. The seat backrest and seat
belts provide the best restraint when the
wearer is in a nearly upright position and
belts are properly positioned on the body.
Your seat must be adjusted so that you can
correctly fasten your seat belt (
page 53).
Never place hands under the seat or near
any moving parts while a seat is being
adjusted.
After adjusting rear seats, make sure
the seats are properly locked
the seat backrests are in an upright po-
sition and are properly locked
Check for secure locking by pushing and
pulling on the seat backrests. If a seat and
seat backrest are not properly locked, the
seat could move forward and the seat back-
rest could fold. The child seat would no long-
er be properly supported or positioned to
provide its intended benefit.
Warning!G
The seat belt only offers its intended protec-
tion when the seat backrest is in a nearly
vertical position and the occupant is sitting
upright. Avoid sitting in positions that pre-
vent the seat belt from being properly posi-
tioned against the body (
page 53). You
should therefore adjust the backrest to a po-
sition as upright as possible.
164.boo Seite 134 Freitag, 30. März 2007 12:54 12
Page 151 of 601
150 Controls in detail
Lighting
Automatic control
Deactivating
Press switch3.
The switch engages in the recessed
position.
The interior lighting and the locator
lighting (
page 176) remain switched
off even when you
unlock the vehicle
open a door
open the tailgate
remove the SmartKey from the
starter switchActivating
Press switch3.
The switch disengages from its
recessed position back to its original
position.
The interior lighting and the locator
lighting (
page 176) come on when
you
unlock the vehicle
open a door
open the tailgate
remove the SmartKey from the
starter switch
The interior lamps go out following an
adjustable time delay (
page 177).Manual control
Switching front/rear interior lighting on
and off
Press front/rear interior lighting
switch4 or2 to switch on the
respective interior light.
Press front/rear interior lighting
switch4 or2 again to switch off the
respective interior light.
Switching front reading lamps on and off
Press front reading lamp switch1
or5 to switch on the respective front
reading lamp.
Press front reading lamp switch1
or5 again to switch off the respective
front reading lamp.
!An interior lamp switched on manually does
not go out automatically.
Leaving an interior lamp switch in the ON
position for extended periods of time with the
engine turned off could result in a discharged
battery.
iThe interior lighting is factory-set to
automatic mode.
iIf a door remains open, the interior lamps
switch off automatically after approximately
5 minutes when the SmartKey is removed or in
starter switch position0.
iAn interior lamp switched on manually does
not go out automatically.
164.boo Seite 150 Freitag, 30. März 2007 12:54 12
Page 160 of 601
159 Controls in detail
Control system
Menus, submenus and functions
Menu1Menu2Menu3Menu4Menu5
Standard displayAUDIONAV*Off-roadDISTRONIC*
(Canada only)
(page 162)(page 164)(page 166)(page 166)(page 167)
Commands/submenus
Trip- and main odometerSelecting radio stationRoute guidance
instructions, current
direction traveledCompassCalling up settings
Checking tire inflation pressureSelecting satellite radio
station*Vehicle level
Checking coolant temperatureOperating CD playerDifferential locks*
Calling up digital speedometer
or outside temperature
Calling up maintenance service
indicator
iThe headings used in the menus table are
designed to facilitate navigation within the sys-
tem and are not necessarily identical to those
shown in the control system displays.The first function displayed in each menu will
automatically show you which part of the system
you are in.
164.boo Seite 159 Freitag, 30. März 2007 12:54 12
Page 167 of 601
166 Controls in detail
Control system
NAV* menu
The
NAV menu contains the functions
needed to operate your navigation system.
Press buttonè orÿ repeatedly
until the message
NAV appears in the
multifunction display.
The message shown in the multifunction
display depends on the status of the navi-
gation system:
With the COMAND system switched
off, the message
NAV Off appears in
the multifunction display.
With the COMAND system switched on
but route guidance not activated, the
direction of travel and, if applicable, the
name of the street currently traveled
on appear in the multifunction display.
With the COMAND system switched on
and route guidance activated, the di-
rection of travel and maneuver instruc-
tions appear in the multifunction
display.
Please refer to the COMAND system
manual for instructions on how to activate
the route guidance system.
Off-road menu
The Off-road menu displays the messages
for air suspension, differential locks* and
the direction into which you are currently
driving.
Press buttonè orÿ repeatedly
until one of the following messages ap-
pears in the multifunction display.Vehicles with air suspension:
Vehicles with air suspension and
differential locks*:Press buttonk orj repeatedly
until the desired setting is found.
For information on air suspension, see “Air
suspension program” (
page 278).
For information on differential locks*, see
“Differential locks*” (
page 204).
For information on the compass, see
“Vehicle submenu” (
page 178) and
“Compass” (
page 344).
164.boo Seite 166 Freitag, 30. März 2007 12:54 12
Page 172 of 601
171 Controls in detail
Control system
The table below shows what settings can
be changed within the various menus.
Detailed instructions on making individual
settings can be found on the following
pages.
Instrument clusterTime/DateLightingVehicleComfort*
(page 172)(page 174)(page 175)(page 178)(page 181)
Selecting speedometer
display modeSetting the timeSetting daytime running
lamp mode (USA only)Compass adjustmentActivating
easy-entry/exit fea-
ture*
Selecting languageSetting the dateSetting locator lightingCompass calibrationSetting fold-in func-
tion* for exterior rear
view mirrors
Selecting display (digital
speedometer or outside
temperature) for status in-
dicatorSetting night security
illuminationAudio search function
Setting interior lighting
delayed shut-offSetting automatic cen-
tral locking
Limiting opening
height of tailgate*
164.boo Seite 171 Freitag, 30. März 2007 12:54 12
Page 175 of 601
174 Controls in detail
Control system
Time/Date submenu
Access the
Time/Date submenu via the
Settings menu. Use the Time/Date
submenu to change the time and date
settings.
The following functions are available:Setting the time
This function is not available if your vehicle
is equipped with the COMAND system and
navigation module*.
Move the selection marker with
buttonæ or ç to the
Time/Date
submenu.
Press buttonj ork repeatedly
until the message
Clock Set Hour, or
Clock Set Minute(s) appears in the
multifunction display.
The selection marker is on the hour
setting.
Example illustration for setting the hour
Press buttonæ orç to set the
hour.Setting the date
This function is not available if your vehicle
is equipped with the COMAND system and
navigation module*.
Move the selection marker with
buttonæ or ç to the
Time/Date
submenu.
Press buttonj ork repeatedly
until the message
Date Set Month,
Date Set Day, or Date Set Year
appears in the multifunction display.
The selection marker is on the month
setting.
Example illustration for setting the month
Press buttonæ orç to set the
month.
FunctionPage
Setting the time174
Setting the date174
iIf your vehicle is equipped with the
COMAND system and navigation module*, see
separate COMAND system operating instruc-
tions for information on how to set the date and
time.
164.boo Seite 174 Freitag, 30. März 2007 12:54 12
Page 177 of 601
176 Controls in detail
Control system
Setting locator lighting
With the locator lighting feature activated,
the exterior lamp switch in positionU
(
page 143) and the interior lighting in au-
tomatic mode (
page 150), the following
lamps will switch on during darkness when
the vehicle is unlocked using buttonŒ
on the SmartKey or SmartKey with
KEYLESS-GO:
Parking lamps
Tail lamps
License plate lamps
Side marker lamps
Front fog lamps
The locator lighting switches off when the
driver’s door is opened.
If you do not open a door after unlocking
the vehicle with the SmartKey, the lamps
will switch off automatically after
approximately 40 seconds.
Move the selection marker with
buttonæ orç to the
Lighting
submenu.
Press buttonj ork repeatedly
until the message
Surround Lighting
Function
appears in the multifunction
display.
The selection marker is on the current
setting.
Press buttonæ orç to switch
the locator lighting function
On orOff.
Turn the exterior lamp switch to
positionU when exiting the vehicle.
The locator lighting feature is
activated.Setting night security illumination
(Headlamps delayed shut-off)
Use this function to set whether you would
like the exterior lamps to remain on for
15 seconds during darkness after exiting
the vehicle and closing all doors.
With the headlamps delayed shut-off
feature activated and the exterior lamp
switch in positionU before the engine
is turned off, the following lamps will
switch on when the engine is turned off:
Parking lamps
Tail lamps
License plate lamps
Side marker lamps
Front fog lamps
If after turning off the engine you do not
open a door or do not close an opened
door, the lamps will automatically switch
off after 60 seconds.
164.boo Seite 176 Freitag, 30. März 2007 12:54 12