2008 MERCEDES-BENZ C300 brake

374 Practical hints
What to do if …?
Lamps in instrument cluster
General information:
If any of the following lamps in the instru-
ment cluster fails to come on during the
bulb self-check when switching on the igni-
tion, have the respective bulb checked and
replaced if necessary.
ProblemPossible cause/consequenceSuggested solution
-The yellow Antilock
Brake System (ABS)
indicator lamp comes on
while the engine is
running.The ABS has detected a malfunction and
has switched off. The BAS, ESP® and EBP
are also switched off (see messages in mul-
tifunction display).
The brake system is still functioning nor-
mally but without the systems specified
above.
If the ABS control unit is malfunctioning,
other systems such as navigation system*
or the automatic transmission* may also be
malfunctioning.
Continue driving with added caution.
Wheels will lock during hard braking, re-
ducing steering capability.
Read and observe messages in the mul-
tifunction display (
page 387).
Have the system checked at an autho-
rized Mercedes-Benz Center as soon as
possible.
Failure to follow these instructions
increases the risk of an accident.

375 Practical hints
What to do if …?
ProblemPossible cause/consequenceSuggested solution
-The yellow Antilock
Brake System (ABS)
indicator lamp comes on
while the engine is
running.The charging voltage has fallen below
10 volts. The ABS has switched off. The
BAS, ESP
® and EBP are also switched off
(see messages in the multifunction display)
The battery may not be charged sufficiently.
Switch off electrical consumers that are
currently not needed, e.g. seat heat-
ing*.
If necessary, have the generator and
battery checked.
When the voltage is above this value again,
the ABS is operational again and the ABS in-
dicator lamp should go out.
-The yellow ABS indicator
lamp comes on while the
engine is running.The ABS is temporarily not available. The
ESP®, BAS and EBP are also unavailable.
The system’s self-diagnosis may not be
completed yet.
The brake system is still functioning nor-
mally but without the systems specified
above.
Drive a short distance with added
caution at a vehicle speed of above
12 mph (20 km/h).
When the ABS indicator lamp goes out,
the ABS, ESP
®, BAS and EBP are avail-
able again.
If the ABS indicator lamp does not go out:
Continue driving with added caution.
Have the system checked at an autho-
rized Mercedes-Benz Center as soon as
possible.
Failure to follow these instructions increas-
es the risk of an accident.

376 Practical hints
What to do if …?
ProblemPossible cause/consequenceSuggested solution
-
vThe yellow ABS malfunc-
tion indicator lamp and
the yellow ESP
® warning
lamp come on while the
engine is running and an
acoustic warning sounds.
ABS and ESP® are switched off due to a
malfunction.
The BAS and EBP are also switched off.
The brake system is still functioning nor-
mally but without the ABS available.Continue driving with added caution.
Wheels may lock during hard braking,
reducing steering capability.
Read and observe messages in the mul-
tifunction display (
page 387).
Have the system checked at an autho-
rized Mercedes-Benz Center as soon as
possible.
Failure to follow these instructions increas-
es the risk of an accident.
;
(USA only)
3
(Canada only)
-
v
The red brake warning
lamp comes on while the
engine is running. In addi-
tion, the yellow ABS mal-
function indicator lamp,
and the yellow ESP
®
warning lamp come on
and an acoustic warning
sounds.
A malfunction in the Electronic Brake Pro-
portioning (EBP) was detected. The ABS,
BAS and ESP
® are also switched off (see
messages in multifunction display).
The brake system continues to function
normally, but without electronic support.
Continue driving with added caution.
Wheels may lock during hard braking,
reducing steering capability.
Read and observe messages in the mul-
tifunction display (
page 387).
Have the system checked at an autho-
rized Mercedes-Benz Center as soon as
possible.
Failure to follow these instructions increas-
es the risk of an accident.

377 Practical hints
What to do if …?
ProblemPossible cause/consequenceSuggested solution
;
(USA only)
3
(Canada only)
The red brake warning
lamp comes on while the
engine is running and an
acoustic warning sounds.You are driving with the parking brake set.Release the parking brake
(
page 130).
The red brake warning
lamp comes on while the
engine is running.There is insufficient brake fluid in the reser-
voir.Risk of accident!
Carefully stop the vehicle in a safe loca-
tion or as soon as it is safe to do so.
Depress the parking brake
(
page 134).
Contact an authorized Mercedes-Benz
Center.
Do not add brake fluid! This will not
solve the problem.
Warning!G
Driving with the brake warning lamp illumi-
nated can result in an accident. Have your
brake system checked immediately if the
brake warning lamp stays on.
Do not add brake fluid before checking the
brake system.
Overfilling the brake fluid reservoir can re-
sult in spilling brake fluid on hot engine
parts and the brake fluid catching fire. You
can be seriously burned.!If you find that the brake fluid in the brake
fluid reservoir has fallen to the minimum mark or
below, have the brake system checked for brake
pad thickness and leaks.

378 Practical hints
What to do if …?
ProblemPossible cause/consequenceSuggested solution
±The yellow engine malfunc-
tion indicator lamp comes
on while driving.There is a malfunction in:

The fuel management system

The ignition system

The emission control system

Systems which affect emissions
Such malfunctions may result in excessive
emissions values and may switch the en-
gine to its limp-home (emergency opera-
tion) mode.
Have the vehicle checked as soon as
possible at an authorized
Mercedes-Benz Center.
An on-board diagnostic connector is
used by the service station to link the
vehicle to the shop diagnostics system.
It allows the accurate identification of
system malfunctions through the read-
out of diagnostic trouble codes. It is lo-
cated in the front left area of the
footwell next to the parking brake pedal.
iIn some states you may be required by law
to have the vehicle serviced as soon as the
engine malfunction indicator lamp comes on.
Check local requirements.

389 Practical hints
What to do if …?
Text messages
Display Possible cause/consequencePossible solution
ABS and ESP
Currently Unavailable
See Operator’s ManualABS and ESP® are not available due to a malfunction.
BAS and the hill start assist are also switched off. It
is possible that the self-diagnostics have not yet
been completed.
The brake system still functions normally.Drive a short distance with gentle turns above a
speed of 12 mph (20 km/h).
The message disappears when ABS and ESP
®
are again available.
The ABS and ESP® were deactivated because of in-
sufficient power supply. The charging voltage has
fallen below 10 volts. BAS and the hill start assist are
also deactivated.
The brake system still functions normally but without
the ABS and ESP
® available.
When the voltage is above this value again, the ABS
and ESP® are operational again and the message in
the multifunction display should disappear.
If the message in the multifunction display does not
disappear:
Have the generator (alternator) and the battery
checked.
ABS and ESP
Inoperative
See Operator’s ManualABS and ESP® are switched off due to a malfunction.
BAS and the hill start assist are also switched off.
The brake system still functions normally but without
the ABS and ESP
® available.
Continue driving with added caution. Wheels
may lock during hard braking, reducing steering
capability.
Have the system checked at an authorized
Mercedes-Benz Center as soon as possible.
Failure to follow these instructions increases the
risk of an accident.

391 Practical hints
What to do if …?
Display Possible cause/consequencePossible solution
Check
Tire Pressure Soon
(Canada only)
The Run Flat Indicator indicates that the
pressure is too low in one or more tires.Carefully bring the vehicle to a halt, avoiding abrupt steering
and braking maneuvers. Observe the traffic situation around
you.
Check and adjust the tire inflation pressure as required
(
page 339).
If necessary, change the wheel (page 440).
Restart the Run Flat Indicator after adjusting the tire inflation
pressure values (
page 343).
Warning!G
Do not drive with a flat tire. A flat tire affects
the ability to steer or brake the vehicle. You
may lose control of the vehicle. Continued
driving with a flat tire will cause excessive
heat build-up and possibly a fire.

397 Practical hints
What to do if …?
Symbol messages
Display Possible cause/consequencePossible solution
-ABS and ESP
Currently Unavailable
See Operator’s ManualABS and ESP® are not available due to a
malfunction. BAS and the hill start assist
are also switched off. It is possible that the
self-diagnostics have not yet been complet-
ed.
The brake system still functions normally.Drive a short distance with gentle turns
above a speed of 12 mph (20 km/h).
The message disappears when ABS and
ESP
® are again available.
The ABS and ESP® were deactivated be-
cause of insufficient power supply. The
charging voltage has fallen below 10 volts.
BAS and the hill start assist are also deacti-
vated.
The brake system still functions normally
but without the ABS and ESP
® available.
When the voltage is above this value again,
the ABS and ESP® are operational again and
the message in the multifunction display
should disappear.
If the message in the multifunction display
does not disappear:
Have the generator (alternator) and the
battery checked.