2008 MERCEDES-BENZ C-Class navigation

133 Navigation
Destination input
Entering a house number
i It is not possible to enter house numbers un-
til the street has been entered. You can only en-
ter those house numbers that are stored in the
digital map. The digital map does not contain all
house numbers for all streets.
In the Enter Destination menu select
“No.”.
The house number list is displayed with
(
page 133) or without predictive
speller (
page 133). The display of the
predictive speller depends on how
many house numbers are available for
the selected street.
House number list with predictive spell-
er
If this list is displayed, the predictive spell-
er 3 is activated automatically.1List entry that best matches the
characters already entered
2List
3Predictive speller
i In the predictive speller 3 you can only se-
lect digits that are currently available. The char-
acters that are available depends on those
already entered and the data for the digital map.
For the steps of

Entering digits

Deleting an entry

Accepting first list entry

Cancelling an entry

Switching to the list without predic-
tive spellerproceed as described under proceed
as described under “City list with
predictive speller” (
page 127).
House number list without predictive
speller
To select house number: Rotate ymz
or slide qmr.
To cancel selection: Select “Back”
and press n.
or
Press the í button.


134 Navigation
Destination input
To confirm selection: Press n.
After the confirmation, the Enter Desti-
nation menu appears again. COMAND
has accepted the selected house num-
ber and entered it automatically in the
Enter Destination menu.
Now you can start the route calculation
(
page 135).
Entering a junction
i A junction can be entered once you have en-
tered a street (
page 131). You can only enter
those junctions that are stored in the digital map.
In the Enter Destination menu select
“Intersection”.
The junction list is displayed with or
without predictive speller
(
page 134). The display of the
predictive speller depends on how
many junctions are available for the se-
lected street.
Junction list with predictive speller
If this list is given in the display, the
predictive speller 3 is activated automat-
ically.1List entry that best matches the
characters already entered
2List
3Predictive speller
i In the predictive speller 3 you can only se-
lect characters that are currently available. The
characters that are available depends on those
already entered and the data for the digital map.
For the steps of

Entering characters

Deleting an entry

Accepting first list entry

Cancelling an entry

Switching to the list without predic-
tive speller
proceed as described under “City list
with predictive speller” (
page 127).Junction list without predictive speller
1+ symbol for additional options
To select a junction: Rotate ymz or
slide qmr.
To cancel selection: Select “Back”
and press n.
or
Press the í button.
To confirm selection: Press n.
After the confirmation, the Enter Desti-
nation menu appears again. COMAND
has accepted the selected junction and
entered it automatically in the Enter
Destination menu. Now you can start
the route calculation (
page 135).

135 Navigation
Destination input
Starting route calculation
i Route calculation can only be started once
all the necessary address data has been en-
tered.
In the Enter Destination menu select
“Start”.
1Destination
2Starts route calculation and then starts
route guidance
If route guidance is not active yet, the
route calculation is started.
If route guidance is already active, you
will be prompted to confirm that route
guidance should be ended.
Select “Yes” or “No”.If you select “Yes” COMAND cancels
route guidance and starts the route cal-
culation to the newly entered destina-
tion.
If you select “No” COMAND resumes
the active route guidance.
During the route calculation, an arrow
points towards the destination, and un-
derneath the message “Calculating
Fast Route...”, for example, is dis-
played.
Route guidance begins after the route
has been calculated (
page 148).
i Route calculation takes some time. The
length of time depends on, e. g. distance to the
destination. COMAND calculates the route using
the digital map data. The calculated route may
deviate from the actual road situation, e. g. as a
result of road works or incomplete map data.
Please refer to the information on the digital map
(
page 112).
If necessary switch to navigation mode
and display menu system
(
page 118).
Select “Destination” K “From Memo-
ry”.
If there are more than 8 entries in the
destination memory, the destination
memory list with predictive speller
(
page 136) is displayed, otherwise
the destination memory list is dis-
played without predictive speller
(
page 137).
i There is always an entry in the destination
memory with the name “My Address”. You can
assign your home address, for example, to this
entry and select it for route guidance
(
page 157). This entry is at the top of the list
in the destination memory.
Entering a destination from the des-
tination memory

136 Navigation
Destination input
Destination memory list with
predictive speller
If this list is given in the display, the
predictive speller 4 is activated automat-
ically.
1Character entered by the user
2Characters added by the system
3List entry that best matches the
characters already entered
4Switches to list without speller
5Press and hold deletes complete entry,
press briefly deletes last character
6Currently unavailable characters
7Currently available characters
8Predictive speller
9Currently selected character
aCancels an entry
bDestination memory listi In the predictive speller 8 you can only se-
lect characters that are currently available. The
characters that are available depends on those
already entered and the content of the destina-
tion memory.
When entering characters, the list entry 3
always displays a city that best matches
the characters already entered. COMAND
automatically adds matching letters
3 to
those characters
2 already entered by the
user.
For the steps of

Entering characters

Deleting an entry

Accepting first list entry

Cancelling an entry

Switching to the list without predic-
tive speller
proceed as described under “City list
with predictive speller” (
page 127).Switching to the destination memory list
without predictive speller
If there are several entries in the destina-
tion that have similar spellings, B is high-
lighted in the speller.
Press n.
You can switch to the list at any point while
entering characters.
Slide qm repeatedly until the list ap-
pears without the speller.
or
Select B and press n.
If COMAND can match the characters en-
tered definitively to one entry, the list ap-
pears automatically without the predictive
speller.

137 Navigation
Destination input
Destination memory list without
predictive speller
To select a destination: Rotate ymz
or slide qmr.
To cancel selection: Press the í
button.
or
Select “Back” and press n.
To confirm selection: Press n.
To start route calculation: Select
“Start”, see also (
page 135).
If necessary switch to navigation mode
and display menu system
(
page 118).
Select “Destination” K “From Last
Destinations”.
1Last destination
To select a destination: Rotate ymz
or slide qmr.
To confirm selection: Press n.
To start route calculation: Select
“Start”, see also (
page 135).
i For more information on the “Last destina-
tions” memory go to (
page 162).
i In some countries, entering destinations via
the map is not possible at vehicle speeds above
apprx. 3 mph. The function becomes available
again as soon as the speed falls below apprx.
2mph.
Using the destination entry via the map, you can
also enter a destination that lies within the digital
map but whose address data is not included in
the digital map.
Opening the map
If at least a city has been entered, se-
lect “Map” in the Enter Destination
menu (
page 126).
or
If necessary display the menu system
in the map display (
page 119).
Select “Destination” K “Using Map”.
In both cases, the map together with
crosshairs appears.
Entering destination from the last
destinationsEntering destination via the map

138 Navigation
Destination input
1Current vehicle location (displayed if
the vehicle location is close to the
crosshairs position)
2Crosshairs
3Information on crosshairs position
4Set map scale
i The display 3 depends on the setting se-
lected in “Information On Map” (
page 123). It
may display the current road if corresponding
data is available in the digital map. Or it displays
the geo-coordinate position of the crosshairs if
“Geo-coordinates display” is activated
(
page 124) and if there is adequate GPS re-
ception.
Moving the map and selecting a desti-
nation
To move the map: Slide qmr, omp or
wmx.
To set the map scale: Rotate ymz.
Rotating clockwise makes the map
smaller, rotating counterclockwise en-
larges it.
To select a destination: Press n.
If the crosshairs are outside the digital
map, a route to this destination cannot
be calculated and the message “The
crosshair is off the map” is displayed.
Select “OK”.
If the destination is within the digital
map, COMAND tries to find the desti-
nation on the map.
If the destination can be found, the En-
ter Destination menu is displayed with
the address of the destination. Other-
wise you will see the entry “Destination
From Map”.
To start route calculation: Select
“Start”, see also (
page 135).
i If route guidance is active, you can enter a
stopover destination. Stopover destinations may
be predefined destinations in the following cate-
gories suggested by COMAND for you to select:

“Mercedes-Benz Service”

“Hospital”

“Gas Station”

“Parking Lot”

“Restaurant”
However, you can also enter destinations other
than those that have been predefined. Select the
menu item “OTHER” for this purpose.
You can influence the route guidance to the main
destination in a specific way using the stopover
function. Once the stopover destination has
been reached, COMAND automatically recalcu-
lates the route to the main destination.
Entering predefined destinations
If necessary switch to navigation mode
and display menu system
(
page 118).
Select “Destination” K “Stopover”.
Entering stopover destination

139 Navigation
Destination input
No stopover destination available yet
Select a category.
A stopover destination exists
To change: Select “Change Stopover”.
Select a category.
Select another stopover destination
Selecting a predefined category
COMAND first searches for destinations
along the route within the selected catego-
ry. COMAND then searches for destina-
tions in the vicinity of the vehicle’s
location.
If COMAND is unable to find any destina-
tions, a message to that effect will be dis-
played.
Select “OK”.
If necessary, select another category.
If COMAND finds destinations, a list is
displayed in the right-hand part of the
screen.Here you will find the stopover destina-
tions in the selected category, sorted
by increasing distance from the current
vehicle location.
The list shows:

Name

Information on the location of the
stopover destination in relation to
the direction of travel and the

Current distance to the stopover
destination.
To choose a destination: Rotate ymz
or slide qmr.
To select a destination: Press n.
The Enter Destination menu appears
and displays the address of the desti-
nation.
To cancel selection: Select “Back”.
To start route calculation: Select
“Start”, see also (
page 135).Entering another destination as stop-
over destination
If necessary switch to navigation mode
and display menu system
(
page 118).
Select “Destination” K “Stopover”.
To enter: Select “OTHER”.
Choose from:

“Address Entry”

“From Memory”

“From Last Destinations”

“From POIs”
Select a menu item.
The rest of the destination entry will vary
depending on the selection made:
For the “Address Entry” option see:
Entering a destination via the address
(
page 126).
For the “From Memory” option see:
Entering a destination from the desti-
nation memory (
page 135).


140 Navigation
Destination input
For the “From Last Destinations” option
see:
Entering destination from the last des-
tinations (
page 137).
For the “From POIs” option see:
Entering a POI (page 141).
To start route calculation: After en-
tering the destination select “Start”,
see also (
page 135).
Deleting stopover destination
An existing stopover destination can be de-
leted.
Switch to navigation mode if neces-
sary.
Select “Destination” K “Stopover” K
“Delete Stopover”.
COMAND deletes the stopover destina-
tion and recalculates the route to the
main destination.