2008 MAZDA MODEL CX-7 Owners Manual (in English)

15
Getting started
Ifnecessary
Rear View
Monitor
Navigation Set Up
lYou can alter the map display conditions, the route guidance conditions and show the
system information.
nStop your vehicle before the following operations. Do not change the settings and destination locations while driving. Minimize the time
spent viewing the monitor screen and listening to the voice guidance while driving.
Operating the system will distract the driver from looking ahead of the vehicle and may
cause an accident.
Always stop the vehicle in a safe location and put the parking brake on before operating
the system.
Before Stepsselect
Warning
MENU
Open
[NAVIGATION SET UP] ( page 20)
( page 22)
( page 16)
( page 24)
( page 18)
( page 23)
'<C)%FSSO4EKI8LYVWHE]1EVGL41

16
RoutingAddress
Book
Getting started
Navigation Set Up
You can change the language of the menu and the voice guidance.
Before Steps
select
select

Language
MENU
Open the [LANGUAGE] screen
Select your preferred language from the list.
'<C)%FSSO4EKI8LYVWHE]1EVGL41

17
Getting started
Ifnecessary
Rear View
Monitor
MEMO
'<C)%FSSO4EKI8LYVWHE]1EVGL41

18
RoutingAddress
Book
Getting started
Navigation Set Up
This function allows you to correct any error in the position or direction of your vehicle display.
Before Steps select
Adjusting Current Position and Direction
select
Open the [Calibrate Position] screen
Move to the correct position and select .
Use
or to adjust the direction in which you are
heading, and select .
Distance
This function automatically corrects any error in the display of the current
position that might occur after tire replacement.
select
You will have to drive about 6 miles (10 km) before distance correction is complete.
Map Vers
The map an
select
Map and so
Calibration
MENU
'<C)%FSSO4EKI8LYVWHE]1EVGL41

19
Getting started
Ifnecessary
Rear View
Monitor
select
.
h you are
urrent
omplete.
Map Version
The map and software version numbers can be confirmed using this function.
select
Map and software versions are now displayed.
'<C)%FSSO4EKI8LYVWHE]1EVGL41

20
RoutingAddress
Book
Getting started
Navigation Set Up
Before Steps
select
select

User Setting
MENU
Open the
[USER SETTINGS]
screen
nMap Color
Select a screen color from to options.
nMap Mode
lAuto : The display will automatically switch between Day
and Night illumination mode when the headlights are
turned off and on respectively.
lDay :The display will be presented in Day illumination mode
regardless of whether the headlights are on or off.
lNight : The display will be presented in Night illumination mode regardless of whether the headlights are on or off.
nDistance
Select the distance unit from or .
nAverage Speed
Set the average speed for each road to be driven.
(This function sets the standard speed (average vehicle speed
for each route) used for calculating the estimated arrival time
when calculating the route time.)
: Average speed setting:Changes back to default
nRoad Restriction Warnings
The display of warnings during route guidance when passing
through areas with traffic restrictions can be turned on or off.
'<C)%FSSO4EKI8LYVWHE]1EVGL41

21
Getting started
Ifnecessary
Rear View
Monitor
Navigation Set Up
Before Steps
select
select
User Setting
MENU
Open the
[USER SETTINGS]
screen
nArrival Time
The time which is displayed until reaching the destination or a
way point can be set as an estimated arrival time or the
remaining time.
Select to display the estimated arrival time, or to
display the remaining time.
nKeyboard Layout
The layout of input keys can be selected as or .
nClock
Allows selection of whether clock is to be displayed.
When the time display setting is switched on in the "USER
SETTINGS" screen on the navigation screen, the time will be
displayed on the navigation, SETTINGS, SOUND, LOAD/
EJECT, and DISPLAY MODE screens.
Even if the display of the clock on the navigation is not set, the
clock on the information display remains displayed.
nBeep
Allows selection of whether beep will sound.
'<C)%FSSO4EKI8LYVWHE]1EVGL41

22
RoutingAddress
Book
Getting started
Navigation Set Up
This function allows you set the categories on the area displayed when the (Point of Interest)
menu is selected on the map. Quick POI enables you store up to six different kinds of
categories which you use most regularly.
1 select
2 Select

Quick POI Selection
MENU
Open the [QUICK POI SELECTION] screen
Select the button for Quick POI storage.
Note
lSelect the category to be changed
: This button allows you to restore the factory
settings.
Select a category.
Once selected, subcategories will be displayed.
: Subcategories from all of the individual categories will be
displayed together.
Select the subcategories to be displayed on the
map.
Repeat the above steps to add further POI markers displayed on the menu.
'<C)%FSSO4EKI8LYVWHE]1EVGL41