2008 INFINITI QX56 diagram

AV-20
< FUNCTION DIAGNOSIS >[AUDIO SYSTEM]
HANDS-FREE PHONE SYSTEM
HANDS-FREE PHONE SYSTEM
System DiagramINFOID:0000000001696034
System DescriptionINFOID:0000000001696035
Refer to the Owner's Manual for Bluetoot
h telephone system operating instructions.
NOTE:
Cellular telephones must have their wireless connection set up (paired) before using the Bluetooth telephone
system.
Bluetooth telephone system allows users who have a Bluetooth equipped cellular telephone to make a wire-
less connection between their cellular telephone and the AV control unit. Hands-free cellular telephone calls
can be sent and received. Personal memos can be created using the Nissan Voice Recognition system. Some
Bluetooth cellular telephones may not be recognized by t he AV control unit. When a cellular telephone or the
AV control unit is replaced, the telephone must be pair ed with the AV control unit. Different cellular telephones
may have different pairing procedures. Refer to the cellular telephone operating manual and the vehicle
Owner’s Manual for more information.
AV CONTROL UNIT
When the ignition switch is turned to ACC or ON, the AV control unit will power up. During power up, the Blue-
tooth feature is initialized and performs various self checks. Initialization may take up to 10 seconds. If a
phone is present in the vehicle and paired with the AV control unit, Nissan Voice Recognition will then become
active. Bluetooth telephone functions can be turned off using the Nissan Voice Recognition system.
STEERING WHEEL AUDIO CONTROL SWITCHES
When buttons on the steering wheel audio control switch are pushed, the resistance in steering wheel audio
control switch circuit changes depending on which button is pushed. The AV control unit uses this signal to
perform various functions while navigati ng through the voice recognition system.
The following functions can be performed using the steering wheel audio control switch:
• Initiate Self Diagnosis of the Bluetooth telephone system
• Start a voice recognition session
• Answer and end telephone calls
• Adjust the volume of calls
• Record memos
MICROPHONE
The microphone is located in the roof console assembly . The microphone sends a signal to the AV control unit.
The microphone can be actively tested during self-diagnosis.
Component Parts LocationINFOID:0000000001696036
Refer to AV- 11 , "Component Parts Location".
Component DescriptionINFOID:0000000001696037
AWNIA0131GB
Part name Description
AV control unit • Receives telephone voice signal from Antenna and Microphone
• Sends telephone voice and voice guidance signals to the speakers
BOSE speaker amp. • Recieves audio signals from the AV control unit
• Outputs amplified audio signals to the speakers.
Revision: March 2010
2008 QX56

AV
AV CONTROL UNITAV-111
< ECU DIAGNOSIS > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P
Wiring DiagramINFOID:0000000001696142
AANWA0067GB
Revision: March 2010 2008 QX56

BCS
BCS-1
ELECTRICAL & POWER CONTROL
C
DE
F
G H
I
J
K L
B
SECTION BCS
A
O P
N
CONTENTS
BODY CONTROL SYSTEM
BCM
BASIC INSPECTION ....... .............................
3
INSPECTION AND ADJUSTMENT ................ .....3
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT .................................................... ......
3
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Description ..................................
3
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Special Repair Requirement .......
3
CONFIGURATION ................................................. ......3
CONFIGURATION : Description ...............................3
CONFIGURATION : Special Repair Requirement ......4
FUNCTION DIAGNOSIS .. .............................5
BODY CONTROL SYSTEM ........................... .....5
System Description ............................................. ......5
Component Parts Location ........................................6
COMBINATION SWITCH READING SYSTEM
.....
7
System Diagram .................................................. ......7
System Description ...................................................7
Component Parts Location ......................................10
SIGNAL BUFFER SYSTEM ...............................12
System Diagram .................................................. ....12
System Description .................................................12
POWER CONSUMPTION CONTROL SYS-
TEM ....................................................................
13
System Diagram .................................................. ....13
System Description .................................................13
Component Parts Location ......................................15
DIAGNOSIS SYSTEM (BCM) ............................16
COMMON ITEM ..................................................... ....16
COMMON ITEM : CONSULT-III Function (BCM -
COMMON ITEM) .....................................................
16
BCM ....................................................................... ....16
BCM : CONSULT-III Function (BCM - BCM) ...........16
DOOR LOCK .......................................................... ....17
DOOR LOCK : CONSULT-III Function (BCM -
DOOR LOCK) ..........................................................
17
REAR WINDOW DEFOGGER ............................... ....17
REAR WINDOW DEFOGGER : CONSULT-III
Function (BCM - REAR DEFOGGER) .....................
17
BUZZER ................................................................. ....18
BUZZER : CONSULT-III Function (BCM - BUZZ-
ER) ..........................................................................
18
INT LAMP ............................................................... ....18
INT LAMP : CONSULT-III Function (BCM - INT
LAMP) ......................................................................
18
MULTIREMOTE ENT ............................................. ....19
MULTIREMOTE ENT : CONSULT-III Function
(BCM - MULTIREMOTE ENT) .................................
19
HEADLAMP ........................................................... ....21
HEADLAMP : CONSULT-III Function (BCM -
HEAD LAMP) ...........................................................
21
WIPER .................................................................... ....22
WIPER : CONSULT-III Function (BCM - WIPER) ....22
FLASHER ............................................................... ....23
FLASHER : CONSULT-III Function (BCM -
FLASHER) ...............................................................
23
AIR CONDITIONER ............................................... ....23
AIR CONDITIONER : CONSULT-III Function
(BCM - AUTO AIR CONDITIONER) ........................
23
INTELLIGENT KEY ................................................ ....24
INTELLIGENT KEY : CONSULT-III Function
(BCM - INTELLIGENT KEY) ....................................
24
Revision: March 2010 2008 QX56

BCS-2
COMB SW .................................................................24
COMB SW : CONSULT-III Function (BCM -
COMB SW) .............................................................
24
IMMU ...................................................................... ...25
IMMU : CONSULT-III Function (BCM - IMMU) .......25
BATTERY SAVER ................................................. ...25
BATTERY SAVER : CONSULT-III Function (BCM
- BATTERY SAVER) ........................................... ...
25
TRUNK ................................................................... ...26
TRUNK : CONSULT-III Function (BCM - TRUNK) ...26
RETAINED PWR .................................................... ...26
RETAINED PWR : CONSULT-III Function (BCM -
RETAINED PWR) ...................................................
26
SIGNAL BUFFER ................................................... ...26
SIGNAL BUFFER : CONSULT-III Function (BCM
- SIGNAL BUFFER) ................................................
26
AIR PRESSURE MONITOR ................................... ...27
AIR PRESSURE MONITOR : Diagnosis Descrip-
tion ..........................................................................
27
AIR PRESSURE MONITOR : CONSULT-III Func-
tion ....................................................................... ...
28
THEFT ALM ........................................................... ...29
THEFT ALM : CONSULT-III Function (BCM -
THEFT ALM) ..........................................................
29
COMPONENT DIAGNOSIS ........................30
U1000 CAN COMM CIRCUIT ......................... ...30
Description ........................................................... ...30
DTC Logic ...............................................................30
Diagnosis Procedure ..............................................30
U1010 CONTROL UNIT (CAN) .........................31
DTC Logic ............................................................ ...31
Diagnosis Procedure ..............................................31
Special Repair Requirement ...................................31
POWER SUPPLY AND GROUND CIRCUIT .. ...32
Diagnosis Procedure ............................................ ...32
COMBINATION SWITCH INPUT CIRCUIT .......33
Diagnosis Procedure ...............................................33
Special Repair Requirement ...................................34
COMBINATION SWITCH OUTPUT CIRCUIT ...35
Diagnosis Procedure ...............................................35
Special Repair Requirement ...................................35
COMBINATION SWITCH ..................................36
Description ........................................................... ...36
Diagnosis Procedure ...............................................36
ECU DIAGNOSIS .......................................38
BCM (BODY CONTROL MODULE) ............... ...38
Reference Value .................................................. ...38
Terminal Layout ......................................................40
Physical Values .......................................................40
Wiring Diagram .......................................................46
Fail Safe .................................................................49
DTC Inspection Priority Chart ...............................50
DTC Index ..............................................................50
SYMPTOM DIAGNOSIS ............................52
COMBINATION SWITCH SYSTEM SYMP-
TOMS .............................................................. ...
52
Symptom Table .................................................... ...52
PRECAUTION ............................................53
PRECAUTIONS .............................................. ...53
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" .............................................................. ...
53
Precaution Necessary for Steering Wheel Rota-
tion After Battery Disconnect ..................................
53
ON-VEHICLE REPAIR ...............................55
BCM (BODY CONTROL MODULE) ............... ...55
Removal and Installation .........................................55
Revision: March 2010 2008 QX56

BCS
BODY CONTROL SYSTEMBCS-5
< FUNCTION DIAGNOSIS > [BCM]
C
D
E
F
G H
I
J
K L
B A
O P
N
FUNCTION DIAGNOSIS
BODY CONTROL SYSTEM
System DescriptionINFOID:0000000001696402
OUTLINE
• BCM (Body Control Module) controls the various electrical components. It inputs the information required to
the control from CAN communication and the signal received from each switch and sensor.
• BCM has combination switch reading function for reading the operation status of combination switches (light,
turn signal, wiper and washer) in addition to a function fo r controlling the operation of various electrical com-
ponents. It also has the signal transmission function as the passed point of signal and the power consump-
tion control function that reduces the power consumption with the ignition switch OFF.
• BCM is equipped with the diagnosis function that perfo rms the diagnosis with CONSULT-III and various set-
tings.
BCM control function list
System Refer to
Combination switch reading system BCS-7, "
System Diagram"
Signal buffer systemBCS-12, "System Diagram"
Power consumption control systemBCS-13, "System Diagram"
Auto light systemEXL-11, "System Diagram"
Turn signal and hazard warning lamp systemEXL-16, "System Diagram"
Headlamp systemEXL-7, "System Diagram"
Front fog lamp systemEXL-15, "System Diagram"
Daytime running light systemEXL-9, "System Diagram"
Interior room lamp control systemINL-6, "System Diagram"
Step lamp systemINL-6, "System Diagram"
Interior room lamp battery saver systemINL-13, "BATTERY SAVER : CONSULT-III Function"
Front wiper and washer systemWW-4, "System Diagram"
Rear wiper and washer systemWW-8, "System Diagram"
Warning chime systemWCS-4, "WARNING CHIME SYSTEM : System Diagram"
Door lock system DLK-10, "DOOR LOCK AND UNLOCK SWITCH : System Diagram"
(NATS) Nissan anti-theft systemSEC-13, "System Diagram"
Vehicle security systemSEC-17, "System Diagram"
Rear window defogger systemDEF-4, "System Diagram"
Intelligent Key systemSEC-9, "System Diagram"
Power window systemPWC-5, "SystemDiagram"
RAP (retained accessory power) systemBCS-26, "RETAINED PWR : CONSULT-III Function (BCM - RETAINED
PWR)"
TPMS (tire pressure monitoring system)
BCS-28, "AIR PRESSURE MONITOR : CONSULT-III Function"
Revision: March 2010 2008 QX56

BCS
COMBINATION SWITCH READING SYSTEMBCS-7
< FUNCTION DIAGNOSIS > [BCM]
C
D
E
F
G H
I
J
K L
B A
O P
N
COMBINATION SWITCH
READING SYSTEM
System DiagramINFOID:0000000001696404
System DescriptionINFOID:0000000001696405
OUTLINE
• BCM reads the status of the combination switch (light, turn signal, wiper and washer) and recognizes the
status of each switch.
• BCM is a combination of 5 output terminals (OUTPUT 1 - 5) and 5 input terminals (INPUT 1 - 5). It reads a
maximum of 20 switch status.
COMBINATION SWITCH MATRIX
LIIA0757E
Revision: March 2010 2008 QX56

BCS-12
< FUNCTION DIAGNOSIS >[BCM]
SIGNAL BUFFER SYSTEM
SIGNAL BUFFER SYSTEM
System DiagramINFOID:0000000001696407
System DescriptionINFOID:0000000001696408
OUTLINE
BCM has the signal transmission function that output
s/transmits each input/received signal to each unit.
Signal transmission function list
ALMIA0263GB
Signal nameInputOutputDescription
Oil pressure switch signal IPDM E/R (CAN) Combination meter (CAN)Transmits the received oil pres-
sure switch signal via CAN
communication.
Revision: March 2010
2008 QX56

BCS
POWER CONSUMPTION CONTROL SYSTEMBCS-13
< FUNCTION DIAGNOSIS > [BCM]
C
D
E
F
G H
I
J
K L
B A
O P
N
POWER CONSUMPTION CONTROL SYSTEM
System DiagramINFOID:0000000001696409
System DescriptionINFOID:0000000001696410
OUTLINE
• BCM incorporates a power consumpt
ion control function that reduces the power consumption according to
the vehicle status.
• BCM switches the status (control mode) by itself with the power saving control function. It performs the sleep
request to each unit IPDM E/R, combination meter and In telligent Key unit) that operates with the ignition
switch OFF.
Normal mode (wake-up)- CAN communication is normally performed with other units
- Each control with BCM is operating properly
CAN communication sleep mode (CAN sleep)- CAN transmission is stopped
- Control with BCM only is operating
Low power consumption mode (BCM sleep)- Low power consumption control is active
- CAN transmission is stopped
LOW POWER CONSUMPTION CONTROL WITH BCM
BCM reduces the power consumption with the following operation in the low power consumption mode.
• The reading interval of the each switches changes from 10 ms interval to 20 ms interval.
Sleep mode activation
• BCM receives the sleep-ready signal (ready) from IPDM E/R, combination meter and Intelligent Key unit via
CAN communication.
• BCM transmits the sleep wake up signal (sleep) to each unit when all of the CAN sleep conditions are ful-
filled.
• Each unit stops the transmission of CAN communicati on with the sleep wake up signal. BCM is in CAN com-
munication sleep mode.
• BCM is in the low power consumption mode and perform the low power consumption control when all of the
BCM sleep conditions are fulfilled with CAN sleep condition.
AWMIA0082GB
Revision: March 2010 2008 QX56