2008 INFINITI QX56 audio

AV-178
< ON-VEHICLE REPAIR >[AUDIO SYSTEM]
AUDIO ANTENNA
AUDIO ANTENNA
Location of AntennasINFOID:0000000001601500
Window Antenna RepairINFOID:0000000001601501
ELEMENT CHECK
1. Attach probe circuit tester (ohm setting) to antenna terminal on
each side.
1. Satallite Antenna 2. Antenna feeder3. Antenna amp, M602
4. Satellite antenna feeder 5. M502, M6016. M78, M550
⇐ To AV control unit
AWNIA1556ZZ
SEL250I
Revision: March 2010 2008 QX56

AV
AUDIO ANTENNAAV-179
< ON-VEHICLE REPAIR > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P
• When measuring continuity, wrap tin foil around the top of
probe. Then, press the foil against the wire with your finger.
2. If an element is broken, no continuity will exist.
3. To locate a break, move probe along element. Tester indication will change abruptly when probe passes the broken point.
ELEMENT REPAIR
Refer to AV-178, "Window Antenna Repair".
SEL122R
SEL252I
SEL253I
Revision: March 2010 2008 QX56

AV-180
< ON-VEHICLE REPAIR >[AUDIO SYSTEM]
SATELLITE RADIO ANTENNA
SATELLITE RADIO ANTENNA
Removal and InstallationINFOID:0000000001601502
REMOVAL
1. Lower the headliner. Refer to
INT-17, "Removal and Installation".
2. Disconnect the satellite radio antenna connector.
3. Remove the satellite radio antenna nut.
4. Remove the satellite radio antenna.
INSTALLATION
Installation is in the reverse order of removal.
LKIA0679E
Revision: March 2010 2008 QX56

AV
GPS ANTENNAAV-181
< ON-VEHICLE REPAIR > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P
GPS ANTENNA
Removal and InstallationINFOID:0000000001601784
REMOVAL
1. Remove the control device. Refer to TM-195, "A/T Shift Selector Removal and Installation".
2. Remove the center console. Refer to IP-20, "
Removal and Installation".
3. Remove the cluster lid D. Refer to IP-12, "
Removal and Installation".
4. Disconnect the center speaker.
5. Remove the defroster grille. Refer to IP-12, "
Removal and Installation".
6. Disconnect the GPS antenna connector.
7. Remove the GPS antenna.
INSTALLATION
Installation is in the reverse order of removal.
WKIA1509E
WKIA1508E
Revision: March 2010 2008 QX56

AV-182
< ON-VEHICLE REPAIR >[AUDIO SYSTEM]
MICROPHONE
MICROPHONE
Removal and InstallationINFOID:0000000001601625
REMOVAL
1. Remove the front roof console finisher. Refer to
INT-17,
"Removal and Installation".
2. Disconnect the Bluetooth microphone connector (A).
3. Detach the Bluetooth microphone (1) from the front roof console finisher and remove the Bluetooth microphone (1).
INSTALLATION
Installation is in the reverse order of removal.
ALNIA0275ZZALNIA0274ZZ
Revision: March 2010 2008 QX56

AV
REAR VIEW CAMERAAV-183
< ON-VEHICLE REPAIR > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P
REAR VIEW CAMERA
Removal and InstallationINFOID:0000000001612979
REMOVAL
1. Remove the back door lower finisher. Refer to INT-21, "Removal and Installation".
2. Remove the license lamp finisher. Refer to EXT-24, "
Removal and Installation".
3. Disconnect the rear view camera connector.
4. Remove the two screws and remove the rear view camera.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
After installing the rear view camera, perform side distance guideline correction procedure. Refer to AV- 7 ,
"REAR VIEW MONITOR GUIDING LINE ADJUSTMENT : Special Repair Requirement".
LKIA0479E
Revision: March 2010 2008 QX56

AV-184
< ON-VEHICLE REPAIR >[AUDIO SYSTEM]
REAR VIEW CAMERA CONTROL UNIT
REAR VIEW CAMERA CONTROL UNIT
Removal and InstallationINFOID:0000000001612980
REMOVAL
1. Disconnect the battery negative terminal.
2. Remove the luggage side finishers LH. Refer to
INT-19,
"Removal and Installation".
3. Disconnect the rear view camera control unit electrical connec- tor.
4. Remove the two screws and remove the rear view camera con- trol unit.
INSTALLATION
Installation is in the reverse order of removal.
LKIA0478E
Revision: March 2010 2008 QX56

BACK DOOR OPENER FUNCTIONDLK-27
< FUNCTION DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
Warning Chime Active Conditions
The warning chime uses two types of audio warnings, a friendly chime and a warning chime. The friendly
chime consists of dings lasting 0.66 seconds each imm
ediately followed by the next ding. The warning chime
consists of beeps lasting 0.33 seconds wit h a pause of 0.33 seconds between each beep.
Reverse Conditions
Operation statusOperation or conditions Warning chime pattern
When auto operation starts Power liftgate switch operation
Friendly chime
2 seconds, 3 dings
Remote keyless entry operation
Back door handle switch operation
Back door close switch operation
When reverse operation starts When reverse request is detected from
power liftgate switch, remote keyless
entry or back door close switch
Friendly chime
1.3 seconds, 2 dings
When obstacle is detected Warning chime
2 seconds, 3 beeps
Operating at low voltage While opening or closing Warning chime
2 seconds, 3 beeps
A/T shift selector lever not in P position Back door close operation
Friendly chime
Continuously dings
Back door open operation Warning chime
Continuously beeps
(until close operation is started)
Type Overload reverse
Operation covered Both directions
Detection method Operation speed and motor current change direction
Pinch strips during back door close operation
Non-reversed area • For about 0.5 seconds immediately after drive motor operation
starts
• Between full open and approx. 7 ° from full open
• Closure operation area (half switch - close switch)
Number of times reverse allowed One reversal is allowed (if a second obstacle is detected during a
power open or close operation, the door reverts to manual mode).
Revision: March 2010
2008 QX56