2008 INFINITI FX35 Body

[x] Cancel search: Body

wheel alignment bolt pattern mirror controls oil dipstick technical data height

Load previous 8 pages

Page 866 of 3924

INFINITI FX35 2008 Service Manual
BL-132
< SERVICE INFORMATION >
DOOR
Adjust the striker so that it becomes parallel with the lock insertion
direction.
Removal and Installation of Front DoorINFOID:0000000001327874
CAUTION:
When rem

Page 867 of 3924

INFINITI FX35 2008 Service Manual
DOOR
BL-133
< SERVICE INFORMATION >
C
D E
F
G H
J
K L
M A
B
BL
N
O P
INSTALLATION
Install in the reverse order of removal.
Removal and Installation of Rear DoorINFOID:0000000001327875
CAUTION:
When

Page 876 of 3924

INFINITI FX35 2008 Service Manual
BL-142
< SERVICE INFORMATION >
BACK DOOR
4. Support the back door lock with a proper material to prevent itfrom falling.
WARNING:
Body injury may occur if no supporting rod is holding the
back door o

Page 877 of 3924

INFINITI FX35 2008 Service Manual
BACK DOORBL-143
< SERVICE INFORMATION >
C
DE
F
G H
J
K L
M A
B
BL
N
O P
1. Remove rear plate assembly. Refer to EI-45, "Component Parts
Location".
2. Remove back door striker mounting screws, and re

Page 878 of 3924

INFINITI FX35 2008 Service Manual
BL-144
< SERVICE INFORMATION >
BACK DOOR
Removal and Installation of Dave Tail Male & Female
INFOID:0000000001327883
REMOVAL
1. Remove the dave tail male.
2. Remove the rear bumper. Refer to EI-17,

Page 880 of 3924

INFINITI FX35 2008 Service Manual
BL-146
< SERVICE INFORMATION >
BACK DOOR LOCK ASSEMBLY
BACK DOOR LOCK ASSEMBLY
Removal and Installation of Back Door Lock & Closure AssemblyINFOID:0000000001327885
REMOVAL
1. Remove back door finishe

Page 899 of 3924

INFINITI FX35 2008 Service Manual
VEHICLE SECURITY (THEFT WARNING) SYSTEMBL-165
< SERVICE INFORMATION >
C
DE
F
G H
J
K L
M A
B
BL
N
O P
Make sure the system is in the armed phase. (The security indicator lamp brinks every 2.4 second

VEHICLE SECURITY (THEFT WARNING) SYSTEMBL-165
< SERVICE INFORMATION >
C
DE
F
G H
J
K L
M A
B
BL
N
O P
Make sure the system is in the armed phase. (The security indicator lamp brinks every 2.4 seconds.)
When the following operation 1 or 2 is performed, t he system sounds the horns and flashes the headlamps for
about 50 seconds.
1. Hood, back door or any door is opened during armed phase.
2. Disconnecting and connecting the battery connector before canceling armed phase.
POWER SUPPLY
Power is supplied at all times
through 10A fuse [No.19, located in the fuse block (J/B)]
to security indicator lamp terminal 1.
through 50A fusible link (letter M, located in the fuse and fusible link box)
to BCM terminal 55.
through 15A fuse [No.22, located in the fuse block (J/B)]
to BCM terminal 42.
through 15A fuse [No.34, located in the fuse and fusible link box]
to horn relay terminal 2.
through 10A fuse [No.71, located in the IPDM E/R]
to IPDM E/R internal CPU.
through 15A fuse [No.78, located in the IPDM E/R]
to IPDM E/R internal CPU.
With the ignition switch in the ACC or ON position, power is supplied
through 10A fuse [No. 6, located in the fuse block (J/B)]
to BCM terminal 11.
INITIAL CONDITION TO ACTIVATE THE SYSTEM
The operation of the vehicle security system is controlled by the doors, hood and back door.
To activate the vehicle security system, BCM must receive signals indicating the doors, hood and back door
are closed and the doors are locked by key fob, Intelligent Key or ignition key.
When a door is open, BCM terminal 12 (passenger side door), 13 (rear RH door), 62 (driver side door), 63
(rear LH door) receives a ground signal from each door switch.
When front door LH is unlocked by power window main switch (door lock and unlock switch),
BCM terminal 22 receives a signal from terminal 14 of power window main switch with power window serial
link.
When front door RH is unlocked by front power window s witch (passenger side) (door lock and unlock switch),
BCM terminal 22 receives a signal from terminal 16 of front power window switch (passenger side) with power
window serial link.
When the hood is open, IPDM E/R receives a ground signal
to IPDM E/R terminal 56
through hood switch terminal 2
through hood switch terminal 1
through body grounds E21, E50 and E51.
The IPDM E/R then sends a signal to the BCM through the CAN SYSTEM.
When the back door is open,
to BCM terminal 58
through back door closure motor terminal 7
through back door closure motor terminal 8
through body grounds B15 and B45.
VEHICLE SECURITY SYSTEM ALARM OPERATION
The vehicle security system is triggered by
opening a door
opening the back door
opening the hood
detection of battery disconnect and connect.
The vehicle security system will be triggered once the system is in armed phase,
When BCM receives a ground signal at terminals 12 (p assenger side door), 13 (rear RH door), 58 (back door),
62 (driver side door), 63 (rear LH door), or rece ives a signal from the IPDM E/R (hood switch).
When the vehicle security system is triggered,
ground is supplied intermittently from IPDM E/R terminals 38 and 60.
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

Page 938 of 3924

INFINITI FX35 2008 Service Manual
BL-204
< SERVICE INFORMATION >
BODY REPAIR
BODY REPAIR
Body Exterior Paint ColorINFOID:0000000001327943
2S: Solid + Clear, 2P: 2-Coat pearl, 3P: 3-Coat pearl, M: Metallic, 3M: 3-Coat Metallic, FPM: I

Load next 8 pages

Page: < prev 1-10 ... 9-16 17-24 25-32 33-40 41-48 49-56 57-64 65-72 ... 312 next >

child lock compression ratio homelink washer fluid fuel reserve glove box