2008 INFINITI FX35 engine

TF-40
< SERVICE INFORMATION >
TRANSFER ASSEMBLY
TRANSFER ASSEMBLY
Removal and InstallationINFOID:0000000001327460
REMOVAL
1. Remove tunnel stay with power tool. Refer to RSU-6, "Removal and Installation".
2. Remove exhaust front tube with power tool. Refer to EX-3
.
3. Remove front and rear propeller shaft. Refer to PR-4
and PR-7.
4. Disconnect transfer assembly harness connector and separate harness from transfer assembly.
5. Remove air breather hose. Refer to TF-39
.
6. Support transfer assembly and transmission assembly with a jack.
7. Remove engine rear member with power tool. Refer to EM-112
(VQ35DE) or EM-237 (VK45DE).
8. Remove transfer mounting bolts and se parate transfer from transmission.
CAUTION:
Secure transfer assembly to a jack.
INSTALLATION
Note the following, and install in the reverse order of removal.
 When installing the transfer to the transmission, install the mount-
ing bolts following the standard below.
 After the installation, check the fluid level and for fluid leakage. Refer to TF-10, "
Inspection".
Disassembly and AssemblyINFOID:0000000001327461
COMPONENTS
Bolt No. 1234
Quantity 4321
Bolt length “ ” mm (in) 75 (2.95) 45 (1.77) 40 (1.57) 30 (1.18)
Tightening torque
N·m (kg-m, ft-lb) 37 (3.8, 27)
SDIA2284E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

WW-4
< SERVICE INFORMATION >
FRONT WIPER AND WASHER SYSTEM
FRONT WIPER AND WASHER SYSTEM
Component Parts and Harness Connector LocationINFOID:0000000001328542
System DescriptionINFOID:0000000001328543
 All front wiper relays (HI, LO) are included in IPDM E/R (intelligent power distribution module engine room).
 Wiper switch (combination switch) is composed of a combination of 5 output terminals and 5 input terminals.
Terminal combination status is read by BCM ( body control module) when switch is turned ON.
 BCM controls front wiper LO, HI, and INT (intermittent) operation.
 IPDM E/R operates wiper motor according to CAN communication signals from BCM.
OUT LINE
Power is supplied at all times
 through 50 A fusible link (letter M, located in fuse, fusible link and relay box.)
 to BCM terminal 55,
 through 15 A fuse [No. 22, located in fuse block (J/B)]
 to BCM terminal 42,
 through 30 A fuse (No. 73, located in IPDM E/R)
 to front wiper relay, located in IPDM E/R,
 through 15 A fuse (No. 78, located in IPDM E/R) and
 through 10 A fuse (No. 71, located in IPDM E/R)
 to CPU located in IPDM E/R.
When the ignition switch is ON or START position, power is supplied
 to ignition relay located in IPDM E/R, from battery direct,
 through 15 A fuse [No. 1, located in fuse block (J/B)]
 to BCM terminal 38,
 through ignition relay, located in IPDM E/R
 to front wiper relay, located in IPDM E/R
 to front wiper high relay, located in IPDM E/R and
 to CPU located in IPDM E/R,
 through 10 A fuse (No. 84, located in IPDM E/R)
 through IPDM E/R terminal 44
 to combination switch terminal 14.
Ground is supplied
PKIC9701E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

WW-30
< SERVICE INFORMATION >
REAR WIPER AND WASHER SYSTEM
REAR WIPER AND WASHER SYSTEM
Component Parts and Harness Connector LocationINFOID:0000000001328576
System DescriptionINFOID:0000000001328577
 Wiper switch (combination switch) is composed of a combination of 5 output terminals and 5 input terminals.
Terminal combination status is read by BCM ( body control module) when switch is turned ON.
 BCM controls rear wiper ON and INT (intermittent) operation.
Power supplied at all times
 through 50 A fusible link (letter M, located in fuse, fusible link and relay box)
 to BCM terminal 55,
 through 15 A fuse [No. 22, located in fuse block (J/B)]
 to BCM terminal 42.
When ignition switch ON or START position, power is supplied
 through 15 A fuse [No.1, located in fuse block (J/B)]
 to BCM terminal 38,
 through 10 A fuse [No. 84, located in IPDM E/R (intelligent power distribution module engine room)]
 to combination switch terminal 14.
Ground is supplied
 to BCM terminals 49 and 52
 through grounds M35, M45 and M85,
 to combination switch terminal 12
 through grounds M35, M45 and M85.
REAR WIPER OPERATION
When the wiper switch is in rear wiper ON position, BCM detects rear wiper ON signal by BCM wiper switch
reading function.
BCM operates rear wiper motor, power is supplied
 through BCM terminal 70
 to rear wiper motor 4.
Ground is supplied
 to rear wiper motor terminal 2
 through grounds B15 and B45.
With power and ground supplied, the rear wiper operates.
PKIC9708E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C