2008 HUMMER H2 spare tire

3. Open the tool bag. The following tools needed to
remove the spare tire and at tire are inside the
tool bag:
A. Jack Handle
B. Jack Handle
Extensions (2)
C. Wheel WrenchD. Wheel Wrench
Extension
E. Wheel Blocks (2)Before proceeding, be sure to set the wheel blocks at
the appropriate tire as previously shown. To use
the wheel blocks:
Remove the wheel blocks
from the tool bag. Then,
lift the wheel block as
shown to lock it into place.
5-85

Removing the Spare Tire (SUV)
The spare tire is attached to the tire carrier. To remove
the spare tire:
In order to remove the spare tire, you may need
someone to assist you.
1. Open the tire carrier. SeeTailgate/Spare Tire
Carrier on page 2-16for tire carrier operation.
2. Unscrew the wing nut on the back of the tire carrier.3. Pull off the license plate holder from the spare tire.
4. Attach the wheel wrench to the wheel wrench
extender to remove the wheel nuts. Turn the
wheel wrench with the wheel wrench extender
counterclockwise to loosen the wheel nuts.
5-87

5. Remove the three wheel nuts holding the spare tire
onto the tire carrier.
6. Pull off the spare tire and gently lower it to the
ground. Set it next to the at tire.
Removing the Flat Tire and
Installing the Spare Tire
Jack (SUV and SUT)
1. Do a safety check before proceeding. SeeChanging
a Flat Tire on page 5-78for more information.
2. To remove the center
cap, place the at end
of the wheel wrench
in the slot on the wheel
and carefully pry the
center cap out.
3. Attach the wheel wrench to the extender.
5-88

{CAUTION:
Raising your vehicle with the jack improperly
positioned can damage the vehicle and even
make the vehicle fall. To help avoid personal
injury and vehicle damage, be sure to t the
jack lift head into the proper location before
raising the vehicle.
8. Turn the wheel wrench clockwise to raise the
vehicle. Raise the vehicle far enough off the ground
so there is enough room for the spare tire to
clear the ground.
9. Remove all the wheel
nuts and take off the
at tire.
{CAUTION:
Rust or dirt on a wheel, or on the parts to which
it is fastened, can make wheel nuts become
loose after time. The wheel could come off and
cause an accident. When you change a wheel,
remove any rust or dirt from places where the
wheel attaches to the vehicle. In an emergency,
you can use a cloth or a paper towel to do this;
but be sure to use a scraper or wire brush
later, if needed, to get all the rust or dirt off.
SeeChanging a Flat Tire on page 5-78.
10. Remove any rust or dirt
from the wheel bolts,
mounting surfaces
and spare wheel.
5-91

{CAUTION:
Never use oil or grease on studs or nuts.
Because the nuts might come loose.
The vehicle’s wheel could fall off, causing
a crash.
11. Install the spare tire.
12. Put the wheel nuts back on with the rounded end
of the nuts toward the wheel.
13. Tighten each wheel nut by hand. Then use the
wheel wrench to tighten the nuts by turning it
clockwise until the wheel is held against the hub.
You will not be tightening the nuts fully yet.
14. Lower the vehicle by turning the wheel wrench
counterclockwise. Then lower the jack completely.
5-92

Storing a Flat or Spare Tire and
Tools (SUT)
Storing the Flat or Spare Tire
Use the following art and text to help you store the
spare or at tire back into its proper location when you
are done.
To store the at or spare tire on the tire carrier:
1. Close the tire carrier. SeeTailgate/Spare Tire
Carrier on page 2-16for tire carrier operation.
2. Place the at or spare tire onto the tire carrier with
the outside of the wheel facing you.
3. Reinstall the three nuts holding spare or at tire to
the tire carrier. Tighten the nuts by hand.4. Use the wheel wrench and the wheel wrench
extension to tighten the nuts rmly. Try to move the
tire back and forth slightly to be sure it is secure.
5-94

5. Slide the license plate holder onto the spare or at
tire. Secure it from the back of the tire carrier with
the wing nut.
If you choose not to reinstall the spare or at tire on
the vehicle, you will still need to reinstall the
license plate holder on the spare tire carrier.
Storing the Jack and Tools
To store the jack and tools:
1. Lower the jack completely.
2. Place the jack in the mounting bracket.
3. Turn the hole at the top of the jack clockwise until
the jack is held tight in the mounting bracket.
4. Push and pull on the jack and retighten if necessary
to make sure the jack is secure.
5. Place the wheel blocks in the tool bag.
6. Place the remaining tools in the tool bag.
5-95

7. Make sure nothing is located under or in front of the
seat and then lift the rear driver’s seat so that the
oor is exposed. SeeSplit Folding Rear Seat
on page 1-8for more information.
8. Place the narrow end of the tool bag under the seat
rails as shown. Slide the tool bag under the rear seat.
Be careful not to pinch the seat cables or electrical
harnesses.
9. Reinstall the strap to the seat rail.
10. Return the seat to the correct position.Storing a Flat or Spare Tire and
Tools (SUV)
Storing the Flat or Spare Tire
Use the following art and text to help store the spare or
at tire back into its proper location when done
changing a tire.
To store the at or spare tire on the tire carrier:
1. Close the tire carrier. SeeTailgate/Spare Tire
Carrier on page 2-16for tire carrier operation.
2. Place the at or spare tire onto the tire carrier with
the outside of the wheel facing out.
3. Reinstall the three nuts holding the spare or the at
tire to the tire carrier. Tighten the nuts by hand.
4. Use the wheel wrench and wheel wrench extension
to tighten the nuts rmly.
5-96