Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual272
Wind deflector removal and installation
1. Remove the wind deflector.
(a) Completely open the sunroof.
(b) Pry the wind guard mounting bracket on the left and
right side guide rails out with a small screwdriver
(according to direction indicated by the arrow).
(c) Pull out the wind deflector.
2. Install the wind deflector.
The locating seat of the wind deflector mounting bracket
should wedge into the location slot of the sunroof assembly
guide rail.
Movable sun visor removal
Precondition: The sunroof panel has been removed and the
sunroof is in the closed position.
1. Remove the sun visor.
Move the sun visor to the front position and then push it to
one side. Pry the front slider on the two sides of sun visor
out of the guide rail with a screwdriver. Then move the sun
visor forward, push it to one side, and pry the rear slider on
the two sides of sun visor out of guide rail with a screw-
driver. Finally, pull out the sun visor.
2. Install the sun visor.
Place the sun visor into the sunroof opening. Install the rear
slider on the two sides of sun visor into the guide rail. Move
the rear movable sun visor backward. Install the front slider
on the two sides of the sun visor into the guide rail.
Caution: Once the mounting bolts of the drive device
have been removed, they must be replaced with new
ones. Adjust the sunroof drive device's position (initial
position).
If the following circumstances happen, the initial position of
the sunroof drive device must be adjusted:
(a) A new drive device has been installed.
(b) The drive device was removed when it was not on the
initial position.
(c) Open or close the sunroof with an emergency operation
wrench.
Location slotBracket locating seat
Downloaded from www.Manualslib.com manuals search engine 273Vehicle Body
Adjust the initial position of drive device
Precondition:
(a) Remove the drive device, but leave the electric plug-in
connected.
(b) The sunroof is on the initial position. Sunroof panel has
been installed correctly.
Caution: The gear of drive device cannot contact
anything while adjusting.
1. Select the "Tilt Sunroof" function (position 1) with the
rotary switch.
2. Select the "Close Sunroof" function (position 2) with the
rotary switch.
3. Select the "Open Sunroof" function (position 3) with the
rotary switch.
4. Select the "Close Sunroof" function (position 2) with the
rotary switch.
5. Mark "1" is shown on the observation panel.
6. The drive device is on the initial position.
Parallel operation condition examination
1. The mark (indicated by the arrow) above the rear guide
device on the window panel's two sides must be level
with the "a" mark on the air guide plate.
2. The air guide plate must be installed in the guide rail
(cannot be manually moved).
Adjust the parallel operation condition
Instructions: Only when the sunroof is on the initial position,
and the drive device and window panel are removed, can the
parallel operation conditions be adjusted.
1. The mark (indicated by the arrow) above the rear guide
device on the window panel's two sides must be level
with the "a" mark on the air guide plate.
2. The air guide plate must be installed in the guide rail
(cannot be manually moved).
3. From the front, slide the top of the guide device and
position it between the two symbols.
4. Position.
Mount the drive device at this position (initial position) and
then examine the initial position.
Sunroof assembly installation
1. Install the sunroof assembly into the ceiling opening
with the help of an assistant.
2. The three dowel pins ("B" position on the diagram)
must be placed in the location holes.
3. Check the condition of the circuit connection.
4. Install the bolts.
Tighten them successively from the left and right side to the
rear part of the sunroof drive device. Tightening torque for
all is 8 N·m.
5. Install the outlet pipe.
6. Insert the drive device plug.
Air guide plate
Guide device
Sunroof assembly
Plastic gasket
Mounting bolt
Drive device
B
BB
