2008 GMC CANYON brake

Getting to Know Your Canyon2
A. Air Outlets
B. Turn Signal/
Multifunction Lever
C.Instrument Panel
Cluster
D. Hazard Warning
Flashers Button
E.Passenger Front
AirbagF. Exterior Lamp Controls
G. Parking Brake Release
H. Horn I.Traction Control
Button/FourWheel
Drive Buttons
(if equipped)
J.Audio System K. Cigarette Lighter
(if equipped)
L. Climate Control
System
M.Accessory Power
Outlet
N. Passenger Airbag
Status Indicator
O. Glove Box
See Section 3 of your Owner Manual.
Instrument Panel
DRIVER INFORMATION
Canyon 2008 A 4/3/07 12:36 PM Page 2

Getting to Know Your Canyon4
Driver Information Center
Your vehicle’s Driver Information Center
(DIC) is located on the instrument panel
cluster. It features a message center
that can display information such as the
trip odometer, vehicle personalizationfeatures and a number of messages orwarnings.
The odometer is automatically displayed
when the engine is started, and showsthe total distance the vehicle has beendriven in either miles or kilometers.
Scroll through the various DIC modes
•Press and release the control stem
located on the DIC.
Display trip odometer information
•Press and hold the control stem for
four seconds.
The display shows the distance traveled
since you last set the trip odometer tozero.
Select the DIC language
1.With the engine off, turn the key to On.
2. Close all doors.
3. Press and release the reset stem
until LANGUAGE is displayed.
4. To view each available language,
press and hold the reset stem for
two seconds.
5. Once the desired language is dis
played, briefly press the reset stem to set your choice.
Warnings and Messages
The following are examples of some of
the warnings or messages that mayappear in the DIC. Have your vehicleserviced as soon as possible:
• BRAKE FLUID
(Brake fluid may be low)
• BRAKE SYSTEM
(Service the brake system)
• ABS (Brake system operates
normally without the antilock brakesystem benefit)
•SERVICE TRACTION (Service
the Traction Control System)
• ENG HOT (Check your engine
coolant temperature gauge)
• SERVICE VEH (Service vehicle)
Acknowledge and clear a warning or
message
• Press and hold the control stem for
one second.
Note:To ensure your own safety and to
protect your vehicle warranty, it’s impor
tant not to ignore the preceding warn
ings. Acknowledge each one and attendto them at your earliest convenience.
Canyon 2008 A 4/3/07 12:36 PM Page 4

Getting to Know Your Canyon18
8. Turn the engine off.
9. Place the transmission shift
lever in Park (P), or First (1) forvehicles equipped with a manualtransmission.
10.Turn the ignition to Lock.
11. Release the parking brake prior to
towing.
Shifting out of Neutral
1. Set the parking brake and press and
hold the regular brake pedal.
2. Shift the transmission to Neutral (N),
or press the clutch pedal for vehicleswith a manual transmission, and turn
the ignition to Run with the engine off.
3.Press the button for the desired
transfer case shift position (2HI,
4HI, or 4LO).
4. After the transfer case has shifted
out of Neutral, the indicator light willgo out.
5. Release the parking brake.6.You may start the engine and shift
the transmission to the desired
position.
See Section 2 of your Owner Manual.
Shift the transfer case into or out of
Neutral
Shifting into Neutral
1. Set the parking brake.
2. Turn the ignition to Run but leave the
engine off.
3. Press the regular brake pedal and
shift the transmission in Neutral (N),or depress the clutch for vehicleswith a manual transmission.
4. Shift the transfer case to twowheel
high.
5.Press and hold the twowheel high
and fourwheel low buttons at the
same time for 10 seconds. TheNeutral (N) light will come on whenthe transfer case shift to Neutral (N)is complete.
6. Start the engine.
7. Press and hold the regular brake
pedal and shift the transmission toReverse (R) for one second; thenshift the transmission to Drive (D) forone second, or First (1) for vehicleswith manual transmissions and letout the clutch, to ensure the transfercase is in Neutral. If not, repeat thisprocedure starting at the third step.
Note: Shifting the transfer case to
Neutral can cause your vehicle to rolleven if the transmission is in Park (P) or
in gear. You or someone else could beseriously injured. Be sure to set the
parking brake before placing the transfer case in Neutral.
Canyon 2008 A 4/3/07 12:36 PM Page 18