9
Manual/Power Lumbar
(if equipped)
The manual lumbar control knob is
located on the outboard side of the driv er’s seat. Turn the knob counterclock
wise to increase lumbar support andclockwise to decrease lumbar support.
The power lumbar control switches for
the driver and passenger seats arelocated on the outboard side of theseats.
See Section 1 of your Owner Manual.
Preventing Window Fogging
To clear fog or frost from the windshield
or side windows, turn the airflow controlknob to one of the following modes:
(Floor/Defog):Use to clear the
windows of moisture and to warm
passengers. This mode splits the air delivery between the windshield and thefloor outlets.
(Defrost):Use to remove fog or
frost from the windshield more quickly.This mode directs most of the air to the windshield.
When you select the floor/defog or
defrost mode, the system automatically
turns off the recirculation mode and runsthe air conditioning compressor. The
recirculation mode cannot be selected
because outside air is needed to removeinterior moisture from the vehicle.
See Section 3 of your Owner Manual.
ENTERTAINMENT
Audio Systems
AM/FM Stereo (if equipped)
Set the clock on the AM/FM stereo
radio
•Press and hold the HR button until
the correct hour appears.
• Press and hold MIN until the correct
minute appears.
Display the time with the ignition off
• Press RCL, HR or MIN.
Presetting Radio Stations
You can set up to 18 station presets
(six AM, six FM1 and six FM2) using the
process shown below.
Set a station
1.Turn the radio on.
2. Press the BAND button to select the
band (AM, FM1 or FM2).
3. Tune to the desired station using the
seek function or tune knob.
4.Press AUTO EQ or AUTO TONE (on
equipped audio systems, as applies
to your radio) to select the soundequalization best suiting the type ofstation selected.
5.Press/hold a numbered button until a
beep confirms storage of the station.
6. Repeat the previous steps for each
pushbutton.
Canyon 2008 A 4/3/07 12:36 PM Page 9
Getting to Know Your Canyon10
AM/FM Stereo with CD/MP3 and
Radio Data System (if equipped)
Set the clock on RDS equipped radios
• Press and hold HR and MN simul
taneously for two seconds until
UPDATED and the clock symbol
appear on the display.
If the time is not available from the
station, NO UPDAT will appear.
Using the RDS
Radios equipped with RDS mode allow
you to:
• Seek only stations with your
preferred programming type.
• Seek stations with traffic
announcements.
• Receive announcements of local
and/or national emergencies.
•Receive and display messages from
radio stations.
RDS features are available only on FM
stations that broadcast RDS information.When tuned to an RDS station, the radiodisplays the station name instead of the
frequency. Most RDS stations broadcasttheir station name, time of day and a
Program Type (PTY).
Access the traffic announcement
feature
• Press the TRAF button.
Access radio station messages
• Press the INFO button when INFO
appears on your radio display.
Access Program Type selections
1. To turn Program Type on, press the
SEEK TYPE button once.
2. Turn the P TYPE knob to select the
Program Type you want.
3. Press the SEEK or SEEK TYPE but
ton and the radio seeks to the firstavailable RDS broadcast of the
selected Program Type.
4. To turn Program Type off (while
seeking), press the SEEK or SEEKTYPE button, or wait for the seek tocomplete. All stations will now be
available when you press the SEEK
button.
Activate the Alternate Frequency
feature
• Press and hold the BAND button for
two seconds to turn it on; repeat to
turn it off.
When turned on, AF ON appears on the
radio display and the radio may switch
to stronger stations of the same PTY.
ALERT!
This message appears on the display
when a local or national emergency
announcementis available. If a CD is
playing, the announcement will override
it. ALERT! announcements cannot beturned off, and are not affected by tests
of the Emergency Broadcast System.
Canyon 2008 A 4/3/07 12:36 PM Page 10
