Chapter 13 Door Glass Regulating and Power Door Lock ControlSection 1 Door Glass Regulating SystemI. Inspection1. Check basic function
(1) Ignition switch is turned "ON" or within 60 s after ignition switch is turned off.
a. Check when rise key of glass regulator switch is pressed, corresponding glass rises, when release, it stops
rising; when press fall key and hold it, corresponding glass falls, when release, it stops falling.
b. Check when glass regulator main control switch lock switch on driver side is pressed,except which on driver
side, other glass regulator switches do not act.
c. Automatic fall: press corresponding glass regulator switch fall key briefly,corresponding glass
regulator motor works, glass falls down to the end; or falls down until rise key or fall key is pressed again.
Notes:
During automatic glass down, if corresponding glass regulator switch fall key is pressed down and held,
glass regulator is changed into manual fall mode; if corresponding glass regulator switch rise key is pressed down
and held, glass regulator is changed into manual rise mode; if corresponding glass regulator switch rise or fall key
is pressed briefly, glass regulator stops work. Press briefly: less than 300ms; press and hold: more than 300 ms.
(2) Close window remotely.
In case setting protection remotely, if a key is pressed for more than 1s, glass regulator automatic window
rising action will be performed, implementation mode: left front, right front, left rear, right back, in the
process of window rise, only one glass regulator is permitted to act, only after glass regulator up to the top,
could the other glass riser act.
2. Glass reguelator switch on driver sideDoor Glass Regulating and Power Door Lock Control-Door Glass Regulating System5-136Glass regulator switch on driver side
Window on front passenger side
Window on driver side
Rear right window
Rear left window
Window locking switch
Interior & Exterior Trim and Accessory -Front Seat Belt6-7Pulley coverUnlock
Lock Notes:
Wrap the sharp end of screwdriver up with adhesive tape before
operation.
4. Use screwdriver to pry open the seat belt pulley cover;
5. Unscrew the bolt and detach the seat belt ring from the car;
6. Disconnect the pre-load insertion of seat belt on the bottom edge
of the middle pillar;
7. Detach the front seat belt from the car;
8. Unfix the clip using the screwdriver and detach the trim from the
right middle pillar;
9.Unscrew two bolts using the spanner and detach the remote adjuster
assembly.
Notice:Only the ignition switch turns to "OFF" position and the battery negative should be disconncted more than
90s, the seat belt with pretensioner can be removed.
III. Seat belt with ELR and pre-tensioner
Seat belt with ELR and pre-tensioner is provided with pre-tensioner which works together with the airbag.
The pre-tensioner is part of airbag assembly. The pre-tensioner is mounted in the retractor and controlled by SDM.
When the front bumping force of the car exceeds a specific value, the pre-tensioner and airbag can be triggered
at the same time. To maintain the pre-tension type of seat belt (retractor), observe all the "Alarm" and
"Operation Instruction".
Warning:
Do not try to remove or repair seat belt pre-tensioner. If any abnormal situations take place, replace the whole
assembly with a new one.
Before working, be sure to read through "Attention for Maintenance", and observe them during working. Any
ignorance can cause injury or the failure of seat belt pre-tensioner.
IV. Inspect Operations of Seat Belt Alarm Lamp (on Driver's side)
1. Turn on the ignition switch and check if the seat belt alarm lamp flashes;
2. Fasten the belt buckle and check if the belt alarm lamp goes out;
3. Turn off the ignition switch;
4. Disconnect the seat belt buckle;
5. Turn on the ignition switch;
6. Connect wiring terminal and make earth connection, and inspect the lamp status of the seat belt. Seat belt lamp:
flashing.
V. Inspect Seat Belt
1. Confirm whether the seat belt is properly mounted.
2. Inspect whether the metal part of seat belt is damaged.
3. If the car vibrates in accidents, pull out the seat belt from the retractor and determine whether the seat belt is
scratched (load limit retractor does not work) by visual inspection and touching.
4.Inspection contents before outer seat belt instalation:When ELR
lock,check the gradient of ELR. Check and make sure the seat belt
can not be locked from any aspect within 15°.When you move the
belt ring device beyond 45° slowly,the seat belt should be locked.
5.After installation check the seat belt lock in this way that draw the
seat belt from belt ring quiekly and the seat belf can be locked
normally.
Attention:
Should the seat belt not comply with the technical specification,
you should replace it.
