2008 GEELY MK wiring

IV. Post-defrost: 1. When engine speed exceeds 700rpm (ignition switch is turned on), defrost work is permitted.
2. Turn on defrost switch, perform defrost work for 12 minutes, if defrost switch is pressed down again during
defrost work, defrost work will stop.
3. During defrost, turn off ignition switch, cancel this defrost.V. Light control: 1. Headlight:
(1) After press remote lock key to close four doors, if remote lock key is pressed down again twice in
succession within in 2s, dipped headlight will extend lighting for 1 minute; if remote unlock key is
pressed down within 60s, dipped headlight control output will be turned off.
(2) During output of 60s low level, if ignition switch is turned on, low level output will stop.
2. Ceiling lamp:
(1) When any of the doors is opened, ceiling lamp illuminates; if door is not closed, ceiling lamp will be
turned off after 10 minutes of delay.
(2) For closing of all doors, ceiling lamp will go out after time delay of 30s;
(3) In case all doors are closed,and ceiling lamp illuminates,ignition switch is turned on,ceiling lamp goes
out.
(4) For remote unlock, ceiling lamp illuminates; in case all doors are closed and ceiling lamp illuminates,
remote lock ceiling lamp goes out.VI. Remote anti-theft 1. Protected state: press lock key on remote controller, while closing four doors, anti-theft indicator lamp will
flashes slowly, indicating that the system enters protected state, when the system is triggered, turn light of the
vehicle will flash, warning horn gives out alarm.
2. Cancel protection: press unlock key on remote controller, while opening left front door, anti-theft indicator
lamp flashes rapidly, if at least one of ignition switch, door is opened within 30 s, anti-theft indicator lamp will
go out; otherwise it will enter secondary anti-theft state.
3. Two stage type protection cancellation: while the system is in triggered state, press any key on the remote
controller, alarm sound will stop, however, the system is still in protected state, and car door is still locked; if the
system continues to receive invasion signal, alarm will ring again after brief stop. To cancel protection completely,
cancel alarm for the first time, then press unlock key once immediately;
4. Secondary anti-theft: after protection is cancelled, if any of ignition switch, door is not opened within 30s,
the system will restore alert status automatically, and lock the car door.
Distribution of centralized controller connector terminals:
Connector on wiring harness, as shown in the figure below (view from outgoing terminal):Centralized Controller System-
Function Inspectior5-134Centralized
controller

Door Glass Regulating and Power Door Lock Control-
Door Glass Regulating System5-1415. Electric circuit diagramfor door glass regnlating system
Please Refer to "MK WIRING DIAGRAM"

Interior & Exterior Trim and Accessory -Front Seat Assembly6-21.Remove the front seat
a. Remove the headrest;
b. Remove the inner and outer seat rail covers;
c. Unfix 4 screws;
d. Disconnect the connector on the back of seat cushion;
e. Remove the front seat.
2. Remove the left front seat cushion outer stopper
a. Unfix the release lever;
b. Loosen 3 clips and then unfasten the outer stopper.
3. Remove the left front seat cushion inner stopper
a. Unfix the screw;
b. Loosen the clip and then unfasten the inner stopper.
4. Remove the left front seat-belt buckle assembly
a. Disconnect the connecting wiring harness;
b. Unfix the screw and then unfasten the seat-belt buckle assembly.
5. Remove the left front backrest trim
a. Turn the backrest over and unfix the C-rings;
b. Remove 2 headrest brackets;
c. Remove the backrest trim.
6. Remove the left front seat cushion trim
a. Remove the C-rings from the back of seat cushion;
b. Remove the seat cushion trim.
7. Remove the seat adjuster
a. Remove the seat rail handle;
b. Unfix the screw and then unfasten the seat rail.
8. Install the front seat assembly
Tips:
Install in reverse order of removal.
Install seat cushion frame with 4 bolts, Torgue:21N.m.
Install FL seat belt buckle assembly. Torgue:43N.m.II. Removal and installation of front seat assembly The operation procedure on the right side is identical with that on the left side.

Chapter 3 Front Seat BeltSeat Belt Reminder SystemI. Component View
II. Fault diagnosis
Possible causes
1. GAUGE fuse;
2. Instrument cluster;
3. Left front buckle assembly
4. Wiring harnessSymptom
Driver's seat belt lamp is not onIII. Alarm system inspection
1. To inspect the left front buckle assembly
Check the conductivity of left front buckle assemblyTerminal Number Seat Belt Required
1<=>2Insert OFF
1<=>2Release ON If you find that the result of the inspection is not the same as
required, you can replace the left front buckle assembly.DriverÕs seat belt reminder lamp
Left front buckleInterior & Exterior Trim and Accessory
-Front Seat Belt6-5

Interior & Exterior Trim and Accessory -Front Seat Belt6-7Pulley coverUnlock
Lock Notes:
Wrap the sharp end of screwdriver up with adhesive tape before
operation.
4. Use screwdriver to pry open the seat belt pulley cover;
5. Unscrew the bolt and detach the seat belt ring from the car;
6. Disconnect the pre-load insertion of seat belt on the bottom edge
of the middle pillar;
7. Detach the front seat belt from the car;
8. Unfix the clip using the screwdriver and detach the trim from the
right middle pillar;
9.Unscrew two bolts using the spanner and detach the remote adjuster
assembly.
Notice:Only the ignition switch turns to "OFF" position and the battery negative should be disconncted more than
90s, the seat belt with pretensioner can be removed.
III. Seat belt with ELR and pre-tensioner
Seat belt with ELR and pre-tensioner is provided with pre-tensioner which works together with the airbag.
The pre-tensioner is part of airbag assembly. The pre-tensioner is mounted in the retractor and controlled by SDM.
When the front bumping force of the car exceeds a specific value, the pre-tensioner and airbag can be triggered
at the same time. To maintain the pre-tension type of seat belt (retractor), observe all the "Alarm" and
"Operation Instruction".
Warning:
Do not try to remove or repair seat belt pre-tensioner. If any abnormal situations take place, replace the whole
assembly with a new one.
Before working, be sure to read through "Attention for Maintenance", and observe them during working. Any
ignorance can cause injury or the failure of seat belt pre-tensioner.
IV. Inspect Operations of Seat Belt Alarm Lamp (on Driver's side)
1. Turn on the ignition switch and check if the seat belt alarm lamp flashes;
2. Fasten the belt buckle and check if the belt alarm lamp goes out;
3. Turn off the ignition switch;
4. Disconnect the seat belt buckle;
5. Turn on the ignition switch;
6. Connect wiring terminal and make earth connection, and inspect the lamp status of the seat belt. Seat belt lamp:
flashing.
V. Inspect Seat Belt
1. Confirm whether the seat belt is properly mounted.
2. Inspect whether the metal part of seat belt is damaged.
3. If the car vibrates in accidents, pull out the seat belt from the retractor and determine whether the seat belt is
scratched (load limit retractor does not work) by visual inspection and touching.
4.Inspection contents before outer seat belt instalation:When ELR
lock,check the gradient of ELR. Check and make sure the seat belt
can not be locked from any aspect within 15°.When you move the
belt ring device beyond 45° slowly,the seat belt should be locked.
5.After installation check the seat belt lock in this way that draw the
seat belt from belt ring quiekly and the seat belf can be locked
normally.
Attention:
Should the seat belt not comply with the technical specification,
you should replace it.

Interior & Exterior Trim and Accessory -Front Seat Belt6-8VI. Attentions:
1. Before mounting, you must check if the product is damaged, cracked or rusted.
2. Place the retractor on the vertical position before pulling out the strap. Check if the strap can be easily pulled
out and rotated and the retractor can be locked.
3. When installing a pretensioning seat belt, check if the emitter head pin deflects and is rusted, etc. The emitter
in the pre-tensioning seat belt can work for 15 years.
4. Check if the buckle lock and connection piece comply with the connection of the car. And check if the buckle
can be opened easily.
5. When fitting the bolts, check if the threads on the nut of coating are clear. Those with welding slag must be
cleaned before fitting the bolts.
6. After pulling out the strap of retractor, no barrier (such as wiring harness, etc.) around the strap is allowed. If
there is, it is necessary to get rid of the barrier to ensure the force of retractor and that the strap is not scratched.
VII. How to handle with scraped seat belt
Tips:
Scrap seat belt provided with pre-tensioner, you have to trigger the pre-tensioner taking the following steps.
1. Check if the storage battery is above 12 V on its positive and negative poles;
2. Check the energizing tool;
Warning:
When energizing the pre-tensioner of seat belt, be sure to use dedicated energizing tool for the pre-tensioner
of seat belt.
3. Connect the special tool with the storage battery and also connect
the red clip on the special tool with the positive terminal of the battery
and connect the black clip with the negative terminal of the battery;
4. If the front seat belt is on the car body and is not taken off,
disconnect the joint of the pre-tensioner of seat belt;
5. Connect the yellow joint of the special tool with the joint of the
pre-tensioner of seat belt;
6. At 10 meter away from seat belt, use a special tool to trigger theAbove 10 meterpre-tensioner of seat belt.
Warning:
a. Ensure that there be no people within 10 meters from the seat
belt;
b. If the seat belt has already been taken down from the car, it is
necessary to cover it using the car wheel with tire to avoid injury.
c. When triggering, explosion will emit loud sound. So it shall be
done outdoors without disturbing local community.
d. When you hold the triggered seat belt, be sure to wear gloves
and goggles.
e. After you have finished the operation, you must wash your hands.
f. Do not pour water, etc. to the energized seat belt pre-tensioner.
7. Place the already triggered seat belt into the ethylene bag and tighten it as you do with other articles.
Warning:
a. Do not dispose untriggered seat belt at will.
b. When the pre-tensioner of seat belt is triggered, the seat belt assembly would be very hot. Therefore, you
cannot touch it until at least 30 minutes after it is triggered.