2008 GEELY MK door lock

Interior & Exterior Trim and Accessory -Roof Trim6-264. Remove the indoor roof lamp assy.
a. Use screwdriver to unfix the 4 buckles and remove the
lampshade;
Tips:
Wrap the sharp end of screwdriver up with adhesive tape before
operation.
b. Unfix 2 screws and the roof lamp assy.
5. Remove the handle assy.
a. Pull down the handle and take out 2 rubber plugs from the holes where two bolts are positioned;
b. Unfasten 2 screws and remove the handle assy.
6. Detach the sun visor tightener.
(Take down anti-clockwise the sun visor fastener.)
7. Remove the top trim
Use a special tool to remove 3 clips and remove the roof trim assy.
8. Installation is basically the reverse of removal.clip

Interior & Exterior Trim and Accessory -Outside Rearview Mirror6-37Chapter 14 Outside Rearview MirrorThe outside rearview mirrors are mounted on the left and right doors. With specially designed rubber sheath, the
rearview mirrors are seamlessly and smoothly joined to the body of vehicle. Meanwhile, they block neither upward
nor backward turn of rearview mirrors upon knocking. Such installation also plays an important role in decreasing
the air resistance coefficient of the whole vehicle.
The mirror glasses are fixed to the supporting plates with double-side adhesive tape. The supporting plates are
connected to the shell of rearview mirrors with ball hinge in order to make sure no glass will scatter that causes
secondary injury, as well as replacing the damaged glasses easily. When the glasses are damaged, the supporting
plates can be taken out of the ball-head mount with tools, and then pressed into the mount again after replacing
the glasses. The turning force of rearview mirror is designed as 30N, which enables easy turn and less hurt/damage
in case human or object knocks the mirror. In addition, the rearview mirrors are equipped with electric adjustment
and heat defrosting.
Notes
When turning over the rearview mirror, please don't put your finger between the exterior rearview mirror and
the hinge in order to avoid extrusion injury!Replacement of Rearview MirrorRemoval procedures
1. Remove the cathode lead wire off the storage battery;
2. Remove the corner decoration of door;
3. Disconnect the plug of electric-driven exterior rearview mirror;
4. Remove the 3 screws;
5. Remove the electric-driven exterior rearview mirror
Installation procedures
1. Mount the rearview mirrors onto the doors
2. Fasten the screws from the lower-left side clockwise
Fastening
Fasten the screws of exterior rearview mirrors with the torque
of 8.0N.m
3. Connect the plug of electric-driven exterior rearview mirrors;
4. Install the corner decoration of door

(4) Rear Wall Parts As shown in Fig.5-5, the rear wall assembly includes rear wall plate, rear wall reinforced plate, luggage
compartment door lock mounting plate and luggage compartment door cross beam etc.Fig. 5-5 Rear Wall Assembly
1. Rear wall upper cross beam
2. Luggage compartment lock
mounting plate big assembly
3. Rear wall left double-hole plate
4. Rear wall outer plate
Fig. 5-6 Roof Assembly
1. Roof outer panel 2. Roof No.1 cross beam 3. Roof No.2 cross beam 4.Roof rear cross beam 5.Roof No.3 cross beam
6. Moon roof reinforcement panel It is mainly used as a cross beam to improve the strength of the rear part of the vehicle and form a luggage
compartment door.5) Roof Assembly The roof assembly includes roof outer panel, roof No.1 and No.2 cross beam, and roof rear cross beam etc.
Inside the roof, there is top interior decoration. There is a heat pad in the center and there is bond between the cross
beam and the roof. The rain from the roof is discharged out of the rear part through the channels at both sides. These
cross beams are used to reinforce the roof's transverse stiffness. For disassembled parts, see Fig. 5-6.(6) Luggage Compartment Main Cover Assembly The luggage compartment main cover assembly includes luggage compartment main cover sub-assembly, rear
seat hook mounting plate assembly, left/right side angle plate, drip channel and reinforced upper cross beam etc.
When the luggage compartment main cover assembly is welded to the left/right side wall, it forms a luggageSurvey -Body Structure7-51 14432526143 2

(2) Front FenderFront fender plays a role in front wheel apron and rotect person safty.And at the same tirne,if also woork as vehicle
styling parts.
For the match relationship between the front fender & engine hood and the front door, see Fig. 5-9.Fig. 5-9 Front Fender related to surrounding parts
A) With Engine Hood (4mm¡À1mm)
B) With Front Door (5mm¡À1mm)(3) Door Assembly Doors have LH/RH front door and rear door.
The door uses hinge gemel with limiting device, which is an open structure.
The door includes door outside plate, door inside plate, bumper and hinge reinforced plate etc.
The door has a complex structure, which is a movable component on the body. It helps the passengers get on/
off the vehicle and form an enclosed cabin with the main structure and the relevant parts. Meanwhile, the doors
are used frequently, so there is high requirement on their reliability and durability.
The outside/inside plate is molded by one complete steel sheet, which can improve the stiffness and precision.
In order to improve the safety when the vehicle is collided from the side, four doors are equipped with door
bumpers.
As shown in Fig. 5-10 and Fig. 5-11, the door assembly is made up of outside plate assembly and inside plate
assembly.Fig. 5-10 Front Door
1. Front door inner panel 2. Left front door inner reinforced panel 3. Front door window opper rail 4. Door lock reinforced panel
5. Left front door inner plate cross beam 6. Front door outer panel 7. Door bumper assembly
8. Front door upper hinge assembly 9. Front door lower hinge assembly 10. Hinge reinforced panel assemblySurvey -Body Structure7-7Engine hood
Front fenderFront door
Front fenderA
B12345678910

Fig. 5-11 Rear Door
1. Rear door inner panel 2. Rear door inner lock mounting panel 3. Rear door glass rail 4. Rear inner plate cross beam
5. Rear door outer panel 6. Door bumper assembly 7. Rear door lower hinge assembly
8. Rear door upper hinge assembly 9. Rear door inner plate hinge reinforced panel(3) Luggage Compartment Cover Assembly As shown in Fig. 5-12, the luggage compartment cover assembly includes luggage compartment cover outside
plate, luggage compartment cover inside plate, luggage compartment cover hinge mounting plate, and luggage
compartment cover lock core mounting plate etc. Fig. 5-12 Luggage Compartment Cover
1. Hinge torsion spring 2. Hinge mounting panel 3. Luggage compartment cover hinge
4. Luggage compartment cover inside panel 5. Luggage compartment cover outside panel
6. Luggage compartment cover lock core mounting panel1234568
79
1Survey -Body Structure7-8