2008 GEELY FC steering

Safety airbag assemble at the side of passenger
1. Note (referring to chapter 1).
2. Use the flash or malfunction diagnostic tool to test the malfunction (referring to chapter
1 and 3).
3. Disconnect the connection of cathode of battery, and do not operate in 60 seconds after
disconnecting.
4. Disassemble the glove box.
5. Disassemble the joint of safety airbag at the side of passenger, and do not damage
airbag wiring harness carefully.
6. Disassemble the safety airbag assembly at the side of passenger.
a. Disassemble three connecting bolts from the bracket of safety airbag assembly at the side of passenger.
b. Take down the safety airbag assembly from panel.
7. Check the safety airbag assembly at the side of passenger (referring to chapter 2).
8. Assemble airbag assembly.
a. Check whether the connection between safety airbag module and airbag short wiring harness is firm.
b. Firstly, insert the module in assembling position from the upside of panel, secondly, align the assem-
bling hole of small bracket on module with the assembling hole on framework of panel, at the same
time, the module cover and panel clearance should be even, and the barb on module should be con-
nected to its position.
9. After assembling, use malfunction diagnostic tool or malfunction indicating light to
check and confirm the malfunction has been removed.
(3) Make three fixed claws mesh steering column.
When changing with new helix cable, it is necessary to disassemble yellow clamp before assembling.
(4) Insert the plug of airbag wiring harness in the plug of helix cable and make this connection firm.
Align the
mark Supplemental restraint system--Disassemble and assemble
 263 
(4) After assembling, use malfunction diagnostic tool or malfunction indicating light to check
and confirm the malfunction has been removed. (5) Connect the lower cover of combination switch.
(6) Connect the upper cover of combination switch with the
lower cover with special bolts firmly.
13. Set the helix cable at middle position
a. Check whether ignition switch locates OFF state.
b. Check whether the cathode end of battery has been
disassembled.
Note: do not operate in 60 seconds after disassembling
cathode end.
c. Turn helix cable anticlockwise with hand until it could not
be turned.
d. Then turn the helix cable clockwise for 2.5 circles to align
the mark.
14. Assemble steering wheel
(1) Inspection before assembling:
z Steering wheel
z Connecting wiring harness
z Safety airbag assembly at the side of driver
(2) Tighten the assembling screws at both sides.
(3) Connection of battery terminal “-”.

Light--Left combination switch
Left combination switch
Change
1. Disassemble decorative board under steering column [67000129]
2. Disassemble left combination switch assembly [67000078]
(a) Take the joint apart.
(b) Loosen fixed jaw and pull left combination switch assembly.
Fixing
claw
 298 

Wiper and cleaner--Right combination switch
Right combination switch
Change
1. Disassemble the lower trim board of the steering
gear
2. Disassemble right combination switch assembly
[67000079]
(a) Disassemble the joints.
(b) Press fixed jaw to separate meshing then disassemble right
combination switch assembly.
Notes: Do not overly press fixed jaw, or it may de
damaged.
 302 
Fixing
claw

Audio system--Outdoor antenna
Outdoor antenna
Change
1. Disassemble battery negative wire
2. Put the front tyre forward
3. Disassemble safety airbag assembly at the side of the driver
4. Disassemble steering wheel
5. Disassemble integration instrument cap
6. Disassemble integration instrument
7. Disassemble panel NO.3 air outlet
8. Disassemble panel NO.1 air outlet
9. Disassemble panel center air outlet trim board
10. Disassemble glove box
11. Disassemble right front pillar trim board
12. Disassemble left front pillar trim board.
13. Disassemble the joint of the safety airbag at the side of the passenger
14. Disassemble panel
15. Disassemble right front door trim board.
16. Disassemble right side trim board.
17. Disassemble antenna assembly [67000136]
(a) Take removable antenna pillar plug apart from radio.
18. Assemble antenna assembly [67000136]
19. Assemble panel
20. Assemble helix cable.
21. Assemble steering wheel
22. Inspect steering wheel whether it dead against the center.
23. Inspect horn button.
24 Assemble horn button
25. Inspect SRS warning light
 312 

Windshield/bodywork glass/wing mirror--Electric rearview mirror control system
Electric rearview mirror control system(option)
Inspect the vehicle
1. Inspect Electric retractable rearview mirror function
(a) Turn the ignition switch to ACC
(b) Inspect operating electric retractable rearview mirror function, when it at different positions.
(1) When retractable switch at steering position and left/right rearview mirror at steering position either,
press retractable switch, inspect left and right rearview mirrors whether they remove from steering
steering positionretractable
position
Electric
retract-
able
operation
Handle
operation
 329 
position to retraction position and stop at it.
(2) When retractable switch at steering position and left/
right rearview mirror at steering position either, if any one
of the rearmirrors can be pushed back by hand, then
press retractable switch to retractable position, inspect
left and right rearview mirrors whether they remove from
steering position to retraction position and stop at it.
(3) When retractable switch at retractable position and left/
right rearview mirror at steering position either, if any one
of the rearmirrors can be pushed back to steering posi-
tion by hand, then press retractable switch to retract-
able position , inspect whether rearview mirrors move to
restricted position only in steering position and stop at
it.
(4) When retractable switch at retractable position and left/
right rearview mirror at retractable position either, inspect
left and right rearview mirrors whether they remove from
retraction position to steering position and stop at it.
(5) When retractable switch at retractable position and left/
right rearview mirror at retractable position either, if any
one of the rearmirrors can be pushed back to steering
position by hand, then press retractable switch to steer-
ing position, inspect whether rearview mirrors move from
restricted position to steering position and stop at it.
steering positionretractable
position
Electric
retract-
able
operation
Handle
operation Electric
retract-
able
operationElectric
retract-
able
operation
Electric
retract-
able o
perationsteering positionretractable
position
steering positionretractable
position

Windshield/bodywork glass/wing mirror--Electric rearview mirror control system
(c) When operating left and right rearview mirrors, inspect whether ignition switch works when turn it to
OFF.
(1) When operating left and right rearview mirrors, turn ignition switch to OFF and inspect rearview
mirrors function whether they stop.
(2) Turn ignition switch to ACC again, inspect whether rearview mirrors work
Clues on: Turn ignition switch to OFF, if you press retractable switch and turn ignition
switch to ACC, then left and right rearview mirrors will move to opposite position.
(d) Inspect whether rearview mirrors work when restricted by others.
(1) When left and right rearview mirrors move to retractable position or steering position, restrict left
and right rearview mirrors manually, inspect retraction stops.
(2) Press retractable switch again, inspect whether it works.(at the opposite direction of stop position)
 330 

Panel/combination instrument-- panel
3 Fixing clamp
4 Fixing clasp
5. Disassemble safety airbag assembly at the side of
driver [67010011] (Referring to page 261)
6. Disassemble steering wheel assembly [67010001]
(referring to page 194)
7. Disassemble Combination instrument cover
[68000077]
(a) Disassemble fixing clamp.
(b) Use screw driver to unclench three fixing clamps and four
fixing clasps, then disassemble Combination instrument.
Hint: before using screw driver, it is necessary to wrap
its needled top with adhesive tape.
8. Disassemble Combination instrument assembly
[67000081]
(a) Disassemble A screw.
(b) Liking that shown in figure, unclench two fixing clamps.
(c) Disassemble the joint, then disassemble Combination in-
strument assembly.
9. Disassemble panel left ventilation hole assembly
[68010010]
Use disassembling tool for trim tape to disassemble panel left
ventilation hole assembly.
Hint: before using screw driver, it is necessary to wrap its
needled top with adhesive tape.
10. Disassemble panel right ventilation hole assembly
[68010011]
11. Disassemble front ashtray
12. Disassemble shift organization trim board assem-
bly [68000076]
(a) Use screw driver to unclench six fixing clamps.
Hint: before using screw driver, it is necessary to wrap
its needled top with adhesive tape.
(b) Disassemble the joint, then disassemble shift organization
trimmain board.
 341 
4 Fixing clasp
6 Fixing clamp

Panel/combination instrument-- panel
6 Fixing clamp
5 Fixing clasp
19. Disassemble upper panel assembly [68010004]
(a) Disassemble D bolt and two A screws.
(b) Use disassembling tool for trim tape to unclench six fixing clamps.
(c) Disassemble upper panel assembly.
20. Disassemble upper/lower trim board of steering column [64000128/64000129]
21. Disassemble left combination switch assembly [67000078] (referring to page 298)
22. Disassemble right combination switch assembly [64000079] (referring to page 302)
23. Disassemble gas spring
Unclench fixing clamp, then disassemble gas spring.
 343  24. Disassemble evaporator ventilation pipe assembly
[67000149]
Disassemble four fixing clamps and evaporator ventilation pipe
assembly.
gas
spring