2008 GEELY FC diagram

Engine mechanism - Camshaft(i) Temporarily tighten fixed bolts.
(j) Check forward mark and figure, and tighten bolts as
sequences shown in the diagram.
Torque: ±0.78N.m
(k) Install camshaft front bearing cover.
Torque: 23 ±1.38N.m
(l) Fix camshaft with variable wrench and then tighten the
fixed bolts of exhaust camshaft timing sprocket.
Torque: 54 ±10.8N.m
Note: be careful not to damage valve lifter.
(m)Check the alignment marks on timing chain and cam-
shaft timing sprocket, and then align the groove of damp-
ing pulley with the timing mark on timing chain hood as
shown in the diagram.Fixing
Tightening57Mark
Mark
Mark
Timing chain hood
Groove

Engine mechanism - Camshaft(n) Install chain tensioner components.
(1) Check o-ring is clean, and buckle on the hook as
shown in the diagram.
(2) Coat engine oil on the chain tensioner, and then
install it.
Torque: 9 ±1.8N.m
Note:when installing the chain temsioner,
buckle on the hook again if plunger has
ejected.
(3) Turn crankshaft counterclockwise to separate the
hook from lock pin on the plunger.
(4) Turn crankshaft clockwise, and check the sliding
parts are blocked by plunger.
Hint: if the plunger does not eject, press the ten-
sion rail toward chain tensioner with
screwdriver or fingers to separate the hook
from lock pin and make the plunger eject.Pushing into
Turning Plunger
Pushing into58Lifting
Hook Pressing
in
Pin
PinHook Sepa-
rate

Engine mechanism - Camshaft14. Adjust valve clearance.
15. Install cylinder head cover components.(a) Install gasket to cylinder head cover.
(b) Eliminate all old sealant (FIPG) materials.
(c) Coat sealant on position shown in the diagram.
Sealant: silicon rubber flange sealant 1596 (Kesaixin
1596).
Notes:Eliminate all oil on contact surface.After coating sealant, finish installation of cylinder
head cover within 3 minutes.After installing, do not refill engine oil within 2
minutes.
(d) Install cylinder head cover and harness bracket with 9
bolts, 2 oil seal washers and 2 nuts.
Evenly tighten bolts and nuts at several times.
Torque: nut: 29 ±5.8N.m
Bolt: 69 ±13.8N.m16. Install drive belt tensioner device.Torque: nut: 29 ±5.8N.m
Bolt: 69 ±13.8N.m17. Install right engine mounting assembly.Torque: 52N.m18. Check there is oil leakage.
59

Engine mechanism - Crankshaft rear oil seal assemblyReplacement1. Remove transmission assembly.
2. Remove clutch assembly and flywheel components.Fix crankshaft with special tool, remove clutch assembly at
first, and then remove flywheel components.3. Remove crankshaft rear oil seal.(a) Cut oil seal mouth with blade.
(b) Prize out oil seal with flathead screwdriver whose sharp
end is winded with tape.
Note: check crankshaft is damaged after removing oil
seal, and repair with abrasive paper (#400) if it is
damaged.4. Install crankshaft rear oil seal [4G18-1002130].(a) Coat a little MP grease on new oil seal lip.
Note: do not let oil seal lip contact with foreign
matters.
(b) Gently knock new oil seal in with special tool and hammer
until the seal surface is parallel and level with the end sur-
face edge of mounting hole.
Note: wipe off redundant grease on crankshaft.5. Install flywheel components and clutch assembly.(a) Fix crankshaft with special tool.
(b) Clean bolts and bolt holes.
(c) Coat bolts with adhesive.
Adhesive: thread locking adhesive 1234 (Kesaixin 1234)
(d) Install flywheel components.
As sequences shown in the diagram, tighten bolts at sev-
eral times.
Torque: (e) Install clutch assembly.6. Install transmission assembly.Special
tool
Cut
positionSpecial
tool62Crankshaft rear oil seal assembly

Engine mechanism - Cylinder cover gasket componentsReplacement1. Take measures to prevent gasoline leaking.
2. Remove timing chain assembly.
3. Remove camshaft.As sequences shown in the diagram, evenly loosen at
several times, and remove 19 bearing cover bolts, and then
remove 9 bearing covers of intake camshaft and exhaust
camshaft.4. Remove cylinder head assembly.(a) Remove warm air water outlet pipe from cylinder head.
(b) As shown in the diagram, evenly loosen 10 cylinder head
bolts with 10mm dual hexagonal sleeves at several times,
and then remove 10 cylinder head bolts and plain washer.
Notes:Be careful not to let washer fall into cylinder head. Incorrect disassembling sequence will cause cylin-
der head warp or chap.5. Remove cylinder head gasket components
[4G18-1003160].
6. Install cylinder head gasket components.Put new cylinder head gasket on the cylinder body.
Notes:Pay attention to installation direction.Gently put down cylinder head to avoid damaging
cylinder head gasket.7. Install cylinder head assembly.Hint: Lock up cylinder head bolts as 2 steps.
(a) Coat a thin layer of engine oil at bolt thread and the bottom
of bolt head.
(b) As shown in the diagram, evenly tighten 10 cylinder head
bolts and plain washer with 10mm dual hexagonal sleeves
at several times.
Torque: 63Cylinder cover gasket components

Engine mechanism - Cylinder cover gasket components(c) Tighten each cylinder head bolt in turn again.
Torque: m
(d) Install heating air water outlet pipe components.
Torque: 8. Install camshaft.(a) Coat engine oil on camshaft journal.
(b) Put 2 camshafts on cylinder head and with cylinder 1 cam-
shaft end toward the direction shown in the diagram.
(c) Check forward remarks and figures of all bearing cover, and
tighten the bolts as sequences shown in the diagram.
Torque:
Camshaft front bearing cover: Camshaft bearing cover: 9. Check idle speed and ignition timing.
10. Check compression pressure.
11. Check CO/HC.64

Cooling - Temperature regulator componentsReplacement1. Remove engine right bottom shield.
2. Discharge engine coolant.
3. Remove drive belt.Slowly turn drive belt tensioner clockwise to loosen the belt;
then remove drive belt and put back the tensioner slowly to
completely loosen it.4. Remove alternator components.(a) Remove rubber cover and nuts.
(b) Uncouple alternator joint.
(c) Remove 2 bolts and alternator.5. Remove water inlet pipe.
6. Remove temperature regulator.
7. Install temperature regulator.(a) Install new gasket to temperature regulator.
(b) As shown in the diagram, install temperature regulator with
inching valve toward upward.8. Install water inlet pipe and joint.Torque: 9. Install alternator installation components.Torque: 12mm bolt head: m
14mm bolt head: 10. Refill engine coolant.
11. Check there is leakage with coolant.
71Temperature regulator components

Starting and charging - Starting systemStarting and chargingStarting systemInspection1. Starter installation componentsNote: this test must be finished within 3 to 5 seconds to
avoid burning out coil.
(a) Remove nut at C terminal to uncouple wire of field coil.
(b) As shown in the diagram, connect battery wire to electro-
magnetic switch, and check drive pinion is pushed outside,
(pull-in coil and hold-in coil).
(c) As shown in the diagram, uncouple negative wire from ter-
minal C after the above connections, and check drive pin-
ion is still at the state of being pushed outside.(Hold-in coil)
(d) Push drive pinion toward armature side, and measure the
clearance between drive pinion end and stop ring.
Standard clearance: 1.0~5.0mm
(e) Uncouple negative wire from electromagnetic switch
housing, and check drive pinion returns back to original
position toward inside.79Terminal C
Terminal 50Terminal C
Terminal 50Terminal C
Terminal 50