2008 GEELY FC window

Windshield/bodywork glass/wing mirror--Fogbroom system
Fog defrost system
Position drawing
Malfunction
All demists (defrosts) do not work
Rear ventilation window Demist (defrost)
do not work
electric rear mirror defrost dose not workcomponents name
1. DEF main relay
2. DEF-IP fuse
3. DEF-m fuse
4. demist switch
5. wiring harness
1. demist wire
2. wiring harness
1. electric rear mirrorreference pages
Malfunction phenomena table
Demist (Defrost)switch
 327 
Demist wire

Windshield/bodywork glass/wing mirror--Fogbroom system
Inspect
1. Inspect the relay
Inspect the conduction of rear window demist(defrost) relay
(mark: DEF)
If the conduction does not accord with the regulations, replace
relay.
 328 
Conditionsavometer terminals regular situations
Always 1-2conduction
Supply battery voltage
between terminal1 and 3-5 conduction
Terminal2

Anti-stealing and door lock--Electric door lock control system
Anti-stealing and door lock
Electric door lock control system
Position of parts (only for reference)
Inspection on automobile
1. Basic inspection for electric door locker.
(a) Press middle control switch to locker closing side, and check the all doors should be locked; then
press middle control switch to locker opening side, and check all doors should be opened.
(b) Insert key in door locker and turn it anticlockwise, and check all doors should be locked; then turn the
key clockwise, and check all doors should be opened.
(c) Check the keeping protection function of the key.
Note: When checking the keeping protection function of the key, it is necessary to open elec-
tric window at the side of driver to prevent its function from losing and lock the key in
automobile.
(1) Insert key in ignition switch.
(2) Open the door, and press middle control switch on the door at the side of driver to locker closing
side, at this time, door locker could not close.
(3) Open the door, and press locker button on the door at the side of driver to locker closing side, at
this time, door locker could not close.
(4) After pressing locker button upwards for over two seconds, and locking driver door; when driver
door is closed and key is not used to lock, check whether all doors could open automatically.
 355 
Door control switch of electric
window main switch assembly
(Used for handle operation)
Door control switch of left front
door locker assembly
(Used for key operation)
Door control light switch
Left rear door locker
assembly
Right front door
locker assembly
Right rear door
locker assembly

Anti-stealing and door lock--Electric door lock control system
3. Check panel junction box assembly.
(a) Check 25A DOOR fuse.
(b) Check conformity relay.
(1) Disassemble F, G, H and I joint on instrument junction
box.
(2) Check the voltage and conduction of every terminal of
joint. (d) Check security function:
(1) When closing all doors, open the driver window to operate door control switch out of automobile.
(2) Take down the key, open driver door, then close the door and lock (not use key). In this situation
above, check that door could not open locker even if door control switch (handle operation) is
pressed to locker opening side out of automobile.
(3) Take down the key, close and use the key to lock driver door. In this situation above, check that
door could not open locker even if door control switch (handle operation) is pressed to locker
opening side out of automobile.
(4) Take down the key, close and use remote control key to lock driver door. In this situation above,
check that door could not open locker even if door control switch (handle operation) is pressed to
locker closing side out of automobile (only applicable for the automobile equipping with remote
control door locker control system).
Hint:
zIn following situation, check whether security has been canceled.
zIgnition switch is turned to ON.
zUse key operation to open the driver door locker.
zAfter door locker is pressed to opening side by hand, door control switch (handle
operation) is pressed to locker opening side.
zUse remote control locker control to open the door (only applicable for the automobile
equipping with remote control door locker control system).
2. Electric window main switch assembly
Operate door control switch by hand to check its conduction.
 356 
Position of switch Terminal connected by avometerRegulated situation
LOCK 5-1 or 5-3Conduction
UNLOCK8-1 or 8-3↑

Anti-stealing and door lock--Electric door lock control system
Malfunction phenomenon
“Door locker control system” does not work
(all).
Door locking/unlocking malfunction (use
handle operation and key operation)
Door locking/unlocking malfunction (use
key)
Malfunction of key keeping protection func-
tion
Only one door locker does not workPossible malfunction part
1. DOOR fuse (panel J/B)
2. Wiring harness
1. Electric window main switch (door control switch)
2. Wiring harness
1.
Door at the side of driver assembly (door control switch)
2. Wiring harness
3. Door locker connecting rod is loosen
1. Anti-versa lock supervising switch
2. Door control light switch
3. Wiring harness
1. Door locker electric motor
2. Wiring harnessReferred page
-
-
359
-
359
-
-
359
-
-
359
-
Malfunction phenomenon table
 358 

Engine cover/automobile door--Front automobile door
8. Disassemble left front glass assembly [68000146]
Hint: insert the cloth in door steel board to prevent it from
scratching the glass.
(a) Turn the door glass until the bolts happens in repairing
hole.
(b) Disassemble two bolts and door glass.
Note: do not damage the door glass.
Hint: pull the door glass upwards to disassemble it.
9. Disassemble seal tape of left front glass guide slot
[68000161]
10. Disassemble left front door glass lift assembly
[67000122]
(a) Disassemble the joint.
(b) Disassemble six bolts and glass lift.
11. Spread lubricating grease on automobile body.
12. Disassemble left front door window glass guide
slot assembly [68000148]
Disassemble the screw and door framework rear lower bracket.
13. Disassemble left front door locker organization as-
sembly [68000152]
(a) Disassemble the joint.
(b) Disassemble connecting rod from exterior handle.
(c) Disassemble the bolt and screw.
(d) Use planetary socket wrench (T30) to disassemble three
planetary screws and door locker.
(e) Disassemble two screws and left front door locker organi-
zation driver.
14. Spread lubricating grease on automobile body.
Spread MP lubricating grease on sliding and turning parts of
lift assembly.
15. Disassemble left front door exterior handle pedestal.
(a) Use planetary socket wrench to disassemble the screw
and door key tank.
(b) Disassemble exterior handle from exterior handle pedestal.
(c) Use planetary socket wrench to disassemble the screw
and left front door exterior handle pedestal.
 370  16. Assemble left front door locker organization assembly [68000152]
(a) Use two screws to assemble left front door locker organization driver.
(b) Use planetary socket wrench (T30) to assemble three planetary screws and front door locker assembly.
Torque: 5.0 N
⋅ ⋅⋅ ⋅
⋅m
(c) Assemble the bolts and screws.
(d) Connect connecting rod to exterior handle.
(e) Connect the joint.

Engine cover/automobile door--Front automobile door
17. Assemble left front door glass lift assembly [67000122]
(a) Use six bolts to assemble left front door glass lift.
Torque: 8.0 N
⋅ ⋅⋅ ⋅
⋅m
(b) Assemble electric window lift and door glass.
(c) Connect electric window switch to wiring harness and turn ignition switch to ON.
(d) Operate UP and DOWN several times by hand repeatedly.
(e) Check whether the AUTO UP→AUTO DOWN of automatic operation is normal.
Hint:
zWhen it is set up again, anti-clamping protection function does not work.
zAfter implementing AUTO UP operation to close window completely, if automobile window
could not be operated downwards, it is necessary to set up the lift again.
(f) Check the function of electric window.
 371  18. Check the function of electric window
19. Assemble repairing hole cover of left front door
Hint:
zWhen assembling repairing hole cover, pull out con-
necting rod and joint from repairing hole cover.
zAfter assembling repairing hole cover, connecting rod
and joint could not be bent or concaved.
zAfter assembling repairing hole cover, it is necessary
to confirm the affixing situation of adhesive tape.

Engine cover/automobile door--Rear automobile doorRear automobile doorOverhaulHint:zWhen assembling, please work by the sequence which is opposite with disassembling
sequence; if necessary, it will have assembling instruction..zOverhaul procedure for right side is same as the left side.1. Disassemble left rear door control panel assembly [68000176]Use screw driver to disassemble left rear door control panel assembly.Fixing
clasp
Fixing
clasp 373  2. Disassemble left rear door inner trim board assem-
bly [68010057](a) Disassemble three screws.
(b) Disconnect the fixing clamp, then pull inner trim board up-
wards to disassemble it.3. Disassemble left door inner handle assembly
[68010051]Disassemble inner handle and two pull cables from inner handle.4. Disassemble left rear door repairing hole cover.Disassemble repairing hole cover.5. Disassemble exterior seal tape of left rear door glass
[68000196]
6. Disassemble seal tape of left rear glass guide slot
[68000199](a) Disassemble seal tape of left rear glass guide slot.7. Disassemble left rear door window glass guide slot
assembly [68000187]Disassemble two bolts and comparting pillar of rear window.8. Disassemble left rear door triangle glass [68000181](a) Disassemble left rear door triangle glass.
Note: do not damage the glass.
(b) Disassemble corner window waterproof rubber from the glass.9. Disassemble left rear glass assembly [68000179]Hint: insert the cloth in the door steel board to prevent the glass from scratching.
(a) Drop the door glass.
(b) Incline door glass and disassemble the roller pole of lift from glass leading slot to disassemble door
glass.10. Disassemble left rear door lift assembly [67000124](a) Disassemble the joint.
(b) Disassemble four bolts and window lift.