2008 GEELY FC warning light

d. Loosen the connectors of all safety airbag system units,
e. Check whether the connector between electronic control unit of safety airbag system and the
circuit between connector of safety belt pre-tension have following situations:
zEarth
zShort connection with power supply
zOpen circuit
f. Are the wiring harnesses above normal?
Normal: malfunction diagnosis ends
Abnormal: change related wiring harness.
8. Malfunction of impact output
Malfunction of safety airbag assembly at the side of passenger (resistance is too big
or too small, short circuit, grounding and so on)
Resting conditionWarning
zIf the treatment is wrong, safety airbag assembly and pre-tension safety belt might be
triggered to unfold and tighten to make heavy human hurt, so, before the treatment, it
is necessary to read repairing warnings carefully.
Refer to repairing warning of safety airbag system.
Possible reason
zConnector between impact output circuit and electronic control unit of safety airbag sys-
tem has malfunction.
zConnector between safety airbag system unit and grounding position has malfunction.
zThe circuit between impact output circuit and electronic control unit of safety airbag
system happens open circuit or short circuit.
zCircuit between safety airbag system unit and grounding position happens open circuit
or short circuit.
zSafety airbag system unit has malfunction.
(1) Check whether this airbag controller has impact output function
a. Set ignition switch at LOCK position
b. Loosen the cathode cable of battery and keep this state for one minute at least
(2) Check whether the connection of impact output connector is good,
(3) Check whether the impact output connecting wire is earth or is short connecting with other wires,
(4) Check whether impact output connecting wire is open circuit,
(5) Check whether the central control door lock control system or electric injection control system of
engine has been changed,
Note: If repairing it by the steps above and requirements, indicating light or diagnostic tool
could display the mistakes before repairing all the time, please do not change it by
yourself, you should contact with the manufacturer as soon as possible avoid wrong
explosion or no explosion when using airbag.
Supplemental restraint system--Remove malfunction
 259 

Light--Light System 280  2. Fog light System
3. Turning and emergency warning light systemEmergency warning light and turn
light does not light
Emergency warning light does
not light (turning light is normal)
Turn light does not light
(Emergency warning light is normalSide turning light does not light
(warning light is normal)
One side of turning light does not
light
One side of turning light does not
light
Only one bulb does not light1. (meter) fuse
2. (turn) fuse
3. ignition switch
4. flasher assembly
5. wiring harness
1. Emergency warning light switch
2. wiring harness
1. turn light switch
2. wiring harness
1. turn light switch
2. wiring harness
3. bulb
1. turn light switch
2. wiring harness
3. bulb
1. turn light switch
2. wiring harness
1. bulb
2. wiring harnessThe light control switch switches on,
the front fog lights do not light (front
combination lights are normal)Lamp switch turn to “HEAD”. front fog
lights do not light (front combination light
do not light)Only one front fog light do not light
Rear fog lights do not light (front
combination lights are normal)
(front fog lights are normal)
Rear fog lights do not light (front fog
lights do not light)1.(front fog light)fuse
2.fog light relay
3.fog light switch
4.wiring harness
1.other parts
2.wiring harness
1.bulb
2.wiring harness
1.fuse
2.rear fog light switch
3.wiring harness
4.bulb
1.other parts
2.wiring harness
3.bulb
4.front fog light switch
5.rear fog light switchphenomena
Possible part
Reference pagesphenomena
Possible partsReference pages

(b) Inspect function of rear fog light.
(1) Turn the ignition switch to ON.
(2) Inspect rear fog light’s situation when every switch works, just as following table.
Light--Light System
(b) Connect joint to directional switch and inspect from wiring harness’s side joint as following table:
Avometer terminals
2-earth
2-earth
3-earth
3-earth
5-earth
6-earth
8-earthcondition
warning light switch OFF → ON
turn light switch (right) OFF → ON
warning light switch OFF → ON
turn light (left) switch OFF → ON
turn light(left) switch OFF → ON
turn light(right) switch OFF → ON
warning light switch OFF → ONregular situation
0V → 0 ⇔ 9Vevery min 60 to 120 times
0V → 0 ⇔ every min 60 to 120 times
0V → 0 ⇔ 9Vevery min 60 to 120 times
0V → 0 ⇔ 9Vevery min 60 to 120 times
over 9V → 0V
over 9V → 0V
over 9V → 0V
2. Inspect rear fog light switch
(a) inspect rear fog light wiring
(1) Disassemble the joint from switch sides and inspect the
joint from wiring harness as following table.
Avometer terminals
1-earth
2-earth
3-earth
5-earth
6-earth
7-earthcondition
normal
light control switch OFF → ON
normal
light control switch OFF → ON
front fog light switch OFF → ON
normalregular situation
conduct
ion
0V → 10-14V
10-14V
not conduct
ion → conduction
not conduction→ conduction
conduction
Situation
Light switch OFF → ON, front fog light switch OFF
Light switch OFF → ON, front fog light switch ON, rear fog light switch ONrear fog light working situations
rear fog light does not light
rear fog light lights
3. Inspect lighting system function
Clues on: key aperture lamp and room light.
Avometer terminals
7-earth
1-earth
1-earth
4-earthcondition
normal
turn light switch ON
turn light switch ON
normalregular situations
conduct
ion
battery voltage
no voltage
battery voltage
Wiring
harness side
 282 

Audio system--Outdoor antenna
Outdoor antenna
Change
1. Disassemble battery negative wire
2. Put the front tyre forward
3. Disassemble safety airbag assembly at the side of the driver
4. Disassemble steering wheel
5. Disassemble integration instrument cap
6. Disassemble integration instrument
7. Disassemble panel NO.3 air outlet
8. Disassemble panel NO.1 air outlet
9. Disassemble panel center air outlet trim board
10. Disassemble glove box
11. Disassemble right front pillar trim board
12. Disassemble left front pillar trim board.
13. Disassemble the joint of the safety airbag at the side of the passenger
14. Disassemble panel
15. Disassemble right front door trim board.
16. Disassemble right side trim board.
17. Disassemble antenna assembly [67000136]
(a) Take removable antenna pillar plug apart from radio.
18. Assemble antenna assembly [67000136]
19. Assemble panel
20. Assemble helix cable.
21. Assemble steering wheel
22. Inspect steering wheel whether it dead against the center.
23. Inspect horn button.
24 Assemble horn button
25. Inspect SRS warning light
 312 

Panel/combination instrument--combination instrument
Indicator light:
Phenomenon
Turning light fails
Distant light failsPossible parts of trouble
1. harness or joint
2. turn light and safety warning light system
3. combination instrument assembly
1. harness or joint
2. left combination switch
3. combination instrument assemblyReference pages
-
-
335
-
-
335
Instrument:
Phenomenon
Revolution counter, petrol guage and
engine water thermometer fail
petrol guage fails or works abnormallyPossible parts of trouble
1. harness or joint
2. (panel) safety fuse
3. combination instrument assembly
1. harness or joint
2. Fuel guage sensor
3. combination instrument assemblyReference pages
-
-
335
-
335
335
Vehicle inspection
1. inspect speed counter
(1) Use speedometer tester to inspect allowed error of speedometer and action of speedometer
Reference: Km/h
speed indicated by speedometer actual speed
20km/h17-23km/h
40km/h35-40km/h
60km/h55-60km/h
80km/h75-80km/h
100km/h95-100km/h
120km/h 114-120km/h
140km/h133-140km/h
160km/h152-160km/h
Notes: tyre wear or tyre pressure too high or too low will increase error.
(2) Inspect speedometer needle offset
Reference: below 0.5km/h
 335 

Panel/combination instrument--combination instrument
2. Inspect output signal of vehicle speed.
(1) When vehicle run at 10km/h, inspect voltage between ter-
minal10 and terminal A1 of combination instrument assembly.
Standards: the voltage pulsates repeatedly between
0V to 5V for thirteen times.
Notes: Inspect the ignition switch “on” connects the
joint
3. Inspect speed gauge
(1) Connect a test tachometer. then startup the engine.
Notes:
zTachometer terminals polarity connects oppositely will damage interior transistors and
LEDs.
zWhen move or disassemble tachometer. do not drop on the ground or knock the surface.
(2) Compare indicted value test tachometer and combination instrument tachometer.
Standard indicted value (rmp) permitted values (rpm)
700 630-770
1,000 (900-1,100)
2,000 (1,850-2,250)
3,000 2,850-3,150
4,000 (3,800-4,200)
5,000 4,750-5,250
6,000 (5,700-6,300)
7,000 6,650-7,350
DC 13.5V, 25°C
(1) Disassemble the joint of fuel meter
(2) Turn ignition switch to ON, inspect indictor position of fuel guage.
Indictor position: F
(3) Connect short terminal1 and terminal2 of wiring harness sides. Turn ignition switch to ON, inspect
indictor position of fuel guage.
Indictor position: F
5. Inspect low fuel level indictor 4. Inspect fuel gauge
The fuel gauge has the function of sensor detection (that is
failure treatment of oil level tachometer)that is when fuel gauge
indictor is at E position, if low oil level warning light doesn”t
light, first should judge whether there have open-loop trouble of
fuel sensor or wiring harness. When sensor fails, fuel indictor
should stop at current position. But if failing time is over 20
seconds, the indictor will return to E position quickly, the in-
strument will at wire break detection. If the normal situation of
detection panel is over 20 seconds, indicator will return to normal.
A1A20
 336 

Panel/combination instrument--combination instrument
(1) Disassemble fuel meter joints or break wire, when indictor is at E, fuel indictor does not light.
(2) Jumper a 300-330
resistor from the corner of terminal1 and termianl2, turn ignition switch to ON,
indictor is at E line, the indictor light lights.
6. Inspect generator water thermometer .
(1) Disassemble joint of generator water thermometer
(2) Turn ignition switch to ON, inspect indictor position of gen-
erator water thermometer.
Indictor position: COOL
(3) Earth 2 terminal of the wiring harness side joint to inspect
indictor position of generator water thermometer.
Indictor position: HOT
1 2 3
7. Inspect untied indictor light of driver seat belt.
(1) Turn ignition switch to ON, Inspect untied indictor light of driver seat belt lights.
(2) Tie the seat belt, inspect untied indictor light seat belt lights off.
(3) Disassemble the joint of safe belt button switch, earth the terminals of wiring harness
(4) Turn ignition switch to ON, inspect untied indictor light seat belt lights on.
8. Inspect low oil pressure indictor
(1) Disassemble the joint of oil pressure switch.
(2) Turn ignition switch to ON.
(3) Earth terminals of wiring harness sides, inspect low oil pressure indictor.
Low oil pressure indictor: light
9. Inspect oil pressure switch
(1) disassemble joints of oil pressure switch,
(2) Inspect the conduction of oil pressure switch terminals and earth.
Generator extinguishes: conduction
Generator works: not conduction
10. Inspect light warning buzzer
(a) Inspect the function of light warning buzzer
Clues on: light warning buzzer works together, only key
reminding buzzer works.
(1) Front combination light switch switches to ON, extract the
key, open driver seat door, inspect light warning buzzer.
Audio buzzer: Audio for 10 seconds in the night to cut
lamp power, in the day cut the lamp instantly.
(2) When buzzer works, do any one of the followings, inspect whether buzzer stop buzzing.
z zz z
zTurn front combination switch to OFF.
z zz z
zClose driver seat door.
z zz z
zInsert the key.
Buzzer Light switch
Key warning
switch
Pull out the key
Open driver door
 337 

Panel/combination instrument--combination instrument
(b) Inspect light warning buzzer function
(1) Disassemble combination instrument.
(2) Connect battery positive wire to terminal A5 and nega-
tive to terminal A1 and A2.
(3) Connect battery positive wire to terminal A18 and nega-
tive to terminalA17,inspect buzzer.
Audio buzzer: long buzzes
(4) When buzzer works, connect battery positive wire to ter-
minal A4,inspect whether buzzer stop working.
11. Inspect key buzzer
(a) Inspect when key buzzer and light warning buzzer works
together, only key buzzer works.
(1) Insert the key, when driver seat door opens, turn ignition
switch to OFF (LOCK or ACC). inspect key buzzer works
1HZ discontinuously.
(b) inspect key buzzer function
(1) Disassemble combination instrument.
(2) Connect battery positive wire to terminal A5 and nega-
tive to terminal A1 and A2.
(3) Connect battery negative wire to terminal A17 and B8,
inspect buzzer which should work discontinuously.
(4) When buzzer works, connect battery positive wire to ter-
minal A4,inspect whether buzzer stop working.
12. Inspect brake system indictor
(a) Inspect parking brake system indictor
Key warning
switch
Key switch
1G gear
Pull out the key
Open driver door
Buzzer
B8
B1
A1A20
(1) Disassemble the joint of parking brake switch, and earth terminals of wiring harness side joints.
(2) Turn ignition switch to ON, inspect brake system indictor light lights.
(b) Inspect brake oil level indicator light
(1) Disassemble the joint of brake oil level indicator light, connect terminal of wiring harness side
joints.
(2) Turn ignition switch to ON, inspect brake system indicator light lights.
 338