2008 GEELY FC rear view mirror

Engine cover/automobile door--Front automobile door
Overhaul
Hint:
zWhen assembling, please work by the sequence which is opposite with disassembling
sequence; but when it has items that need to pay special attention, it will add special
specification.
zOverhaul procedure for right side is same as the left side.
zPlease refer to subassembly figure of front door on page 360.
1. Disassemble left front door control panel assembly [68000142]
(a) Disassemble the screw.
(b) Use screw driver to disassemble left front door control panel assembly.
Hint: before using screw driver, it is necessary to wrap its needled top with adhesive tape.
(c) Disassemble the joint.
2. Disassemble left front door inner defending board assembly [68010049]
(a) Disassemble the screw.
(b) Without equipping with door control light: use screw driver to disassemble door inner defending board
assembly.
(c) Equipping with door control light: use screw driver to disassemble door inner defending board assembly,
then disassemble the joint again.
(d) Equipping with door control light: use screw driver to disassemble door control light.
3. Disassemble left door inner handle assembly [68010051]
(a) Disassemble inner handle, and disassemble two pull cables from inner handle.
4. Disassemble repairing hole cover of left front door
5. Disassemble left front small loudhail cover assembly [67000131]
 369  6. Disassemble left exterior electric rearview mirror
assembly [67000155]
(a) Disassemble the joint.
(b) Disassemble three screw caps and left exterior electric
rearview mirror.
7. Disassemble exterior seal tape of left front door glass
[68000158]

Exterior/inner trim board--Inner trim board of top
left pillar [68010018]
13. Disassemble upper inner trim board assembly of
right pillar [68010025]
(a) Disassemble the bolt and upper fixing bolt trim cover of front
safety belt.
(b) Use screw driver to disassemble upper inner trim board of
right stand pole.
Hint: before using screw driver, its needled top should
be twisted by adhesive tape.
(C) Use same method to disassemble the trim board at the
other side.
14. Disassemble upper inner trim board assembly of
left pillar [68010023]
15. Disassemble rear row chair cushion (referring to
page 352).
16. Disassemble rear row chair backrest (fixing type)
(referring to page 354).
17. Disassemble rear row chair right backrest assem-
bly (referring to page 352).
18. Disassemble rear row chair left backrest assembly
(referring to page 352).
19. Disassemble inner trim board of right rear pillar
assembly [68010027]
(a) Use screw driver to disassemble inner trim board of right
rear pillar assembly.
Hint: before using screw driver, its needled top should
be twisted by adhesive tape.
(b) Use same method to disassemble the trim board at the
other side.
20. Disassemble inner trim board of left rear pillar as-
sembly [68010026]
21. Disassemble inner trim board of right front pillar
assembly [68010017]
(a) Use screw driver to disassemble inner trim board of right
front pillar assembly.
Hint: before using screw driver, its needled top should
be twisted by adhesive tape.
(b) Use same method to disassemble the trim board at the
other side.
22. Disassemble inner trim board of left front pillar as-
sembly [68010014]
23. Disassemble inner rear view mirror assembly [67010013]
(a) Use screw driver to disassemble trim cover of inner rearview
mirror pedestal.
Hint: before using screw driver, its needled top should
be twisted by adhesive tape.
(b) Disassemble two screws and inner rearview mirror assembly.
Fixing
clamp
Fixing
clamp
Fixing
clamp
 391 

Electric rearview mirrorElectrical schematic diagram--Electric rearview mirror 401