2008 GEELY CK lock

3336Install the headrest;
7Install the front seat with 4 tightening bolts. Torque: 14.72~23.52N.m.3.Adjust1The seat can adjust tilt angle forward in torque 2° x 5=10°;
Adjust backwards 2° x 27=54°;
2The seat assembly slides forwards 15mm x 4=60mm in torque 15N.m;
Slide backwards 15mm x 10=150mm;
3The headrest can be adjusted in 3 positions in height.Rear Seat1.Rear seat back
1Removal
a. Lift the rear seat back lock handle upwards. Turn seat back down forwards. Remove 4 set bolts.
Remove seat backassembly from the vehicle;
b. Remove seat back lock handle and handle seat;Install Front and Rear Seat Snap RingInstall Headrest SupportTrack Assembly Adjuster AssemblyInstall Adjuster and Track AssemblyAssemble the Seatback and Cushion

334c . Remove the snap ring from the rear seat back. Open the seat back cover. Remove the inside snap
ring. Remove the seat cover.
2Re-assembly
a. Install the snap ring at the inside of the seat back;
b. Install the snap ring at the rear seat back;
c. Install the seat back lock handle seat to the rear seat back;
d. Install the rear trunk carpet to the rear seat back with 10 clips;
e. Install the rear seat back assembly to the vehicle with 4 bolts. Tighten bolt torque: 3.92~6.86N.m.2.Rear seat cushion assembly1Removal
a. First remove therear seat back;
b. Lift the front of the seat cushion. Disconnet the seat cushion from the clamp on the floor, push
backwards, separate it from the hook. Remove seat cushionassembly from the vehicle;
c. Remove the snap ring on the seat cushion;
d. Remove the snap ring in the cover. Remove cover.
e. Remove the clamp under the seat cushion;
2Re-assembly
The installation is in the reverse order of the removal.Remove Rear Seatback AssemblySeatback Lock handleHandle SeatRemove Seatback Set BoltRemove Seatback CoverRemove Seatback Handle and Seat

335(VII) Seat BeltThe vehicle seat belt is compulsory for drivers and passengers for safety purpose. It is the facility to prevent
the passengers from being hurt or reduce the possibility of being hurt when the vehicle is in emergent drive or
traffic accident occurs. Ck-1 front seat adopts Three Points Emergency Lock Retractor Pretension Seat
Belt , It is composed of retractor assembly, belt buckle assembly and height adjuster assembly.
1. Height Adjuster Assembly 2. Retractor Assembly 3. Belt Buckle Assembly 4.anchorage1. Belt BuckleBelt buckle is enclosure type, See FigureReplacement Of The Seat Belt Buckle(1) Remove the seat adjuster hinge cover;
(2) Remove the bolt from the belt buckle on the seat side;
(3) Remove the seat belt buckle from the seat;
(4) Replace the seat belt buckle.41
23

3362. RetractorThe retractor is pre-tensioner. The retractor will pre-tension the seat belt when something emergency hap-
pens to prevent passengers from being hurt. It can sense the vehicle acceleration and the acceleration of the
belt being pulled out.
The retractor belt can be pull out and drawn back freely. It will not be locked at 12° around the safety
position, but locked at over 27°. The passenger can move in small area. The pre-tensioner will transmit within
5ms~10ms when something emergency happens to tension and lock the belt.Notice:1 . Check the product for damage, crack and rust before installation.
2 . Put the retractor vertically and the belt can be pulled out. Check if the belt can be pulled out
and around. Check if the retractor works.
3 . When installing the pretensioned seat belt, check the transmittor head pin for slant and rust.
The transmitter in the pretensioned seat belt can be used for 15 years after installation.
4 . Check if the belt buckle and the attachment matches the connecting mode of the to-be-installed
vehicle module. Check if the opening of the buckle is flexible.
5 . See if the screw thread of the nut welded on the cover is clear when installing the bolt. Assemble
the bolt after clearing the welding residue if there is any.
6. When the retractor belt is pulled out, there should be no obstacles around the belt (such as,
wire harness ect) , Remove the obstacles and make sure the retractor and the belt will not be
scratched.
3.Front seat belt removal/installation
Warning:
Do not remove retractor.(1) Turn the ignition switch to LOCK.
(2) Disconnect the negative (--) terminal cable from the battery
for 1min.
(3) Remove B- pillar lower frame.
(4) Pry the seat belt which is used to install the tension wheal.
Use a screwdriver to pry off the stop plate of the seat
belt connector with tensioner.
(5) Disconnect the seat belt connector with tensioner.
Remove 2 set bolts on the hang ring and remove the hang
ring.
(6) Remove two set bolts in the retractor and remove the
front seat belt.
(7) The installation is in the reverse order of the removal.Stop PlateBoltFront Seat BeltScrew
BoltLid

350(XVI) DoorFront DoorFront Door Components:
1.Front Door 2.Front Door Hinge 3.Front Door Lock And Door Lock Actuator
4.Front Door Inner Trim Board 5.Power Window Motor 6.Power Window Actuator
7.Door Inside Handle8.Protection Device 9.Door Outside Handle10.Front Door Lock Hole
11.Front Door Glass 12.Door Window Regulator Run 13.Front Door Weatherstrip A
14.Front Door Lower Weatherstrip 15.Front Door Weatherstrip B16.Front Door Lock Striker11
16 10
8 9
3
15
14
13 4 5 6
1 12
2 7

353(2) Get the window regulator from the hole in the lower door
4.Front Door Lock And Door Lock Actuator Removal/In-
stallation
(1) Remove front door component.
(2) Remove the screw and then remove the front door lock and
the door lock actuator.
(3) The installation is in the reverse order of the removal.Power Window Glass
Regulator Actuator
Power Window Glass
Regulator MotorFront Door ComponentScrewFront Door Lock Latch
and Lock Motor

354Rear door
Rear door Component
1.Rear Door 2.Rear Door Hinges 3.Rear Door Lock And Door Lock Actuator
4.Rear Door Inner Trim Board 5.Power Window Motor 6.Power Window Actuator
7.Door Inside Handle 8.Door Outside Handle 9.Rear Window Glass 10.Quarter Window
11.Window Glass Regulator Run 12.Glass Run13.Quarter Window Weatherstrip
14. Rear Door Weatherstrip A 15.Rear Door Lower Weatherstrip 16.Rear Door Weatherstrip B
17.Rear Door Lock Striker
1.Rear Door Removal/Installation
(1) Disconnect the negative (--) terminal cable from the battery.
(2) Remove the connector.
(3) Remove rear door hinges.
(4) Remove the rear door
(5) The installation is in the reverse order of the removal.
(6) Adjust the rear door. (See Rear door Adjustment)1
2 3
4
5 6
7 8
9 10
12 13
15 11 14 17
16

355Rear Doorinside Trim
Rear Doorinside Trim Component:
1.Rear Doorinside Trim Board Assembly2.Rear Door Lock Inner Handle Assembly
3.Controller
Trim Board 4.Door Handle5.Set Screw
1.Rear doorinside trim board removal/installation
(1) Remove the set screw. (See Figure 5)
(2) Remove the rear door inside trim board assembly.
(3) Disassemble the inside trim board assembly as required
(4) The installation is in the reverse order of the removal.1 2 3 4 5