2008 GEELY CK torque

93Replacement1. Remove the clutch cable
(1) Loosen the clutch adjusting nut. Separate the clutch cable from the accelerator rocker arm
(2) Remove the 2 set bolts from the clutch cable on the cowl panel
(3) Separate the clutch cable from the clutch pedal
2. Install the clutch cable assembly in the reverse order of the above procedure.
Notice:
(1) The clutch cable assembly on the cowl panel set bolt torque : 20~25N.m
(2) Check and adjust the pedal according to the above-mentioned requirement in
"Adjustment".Adjusting BoltStrokeFree
StrokeMinimum Distance from the Cowl Panel Adjusting Bolt
NutInstall HeightAdjusting Nut

966. Remove clutch hydraulic control master cylinder
Remove the 2 fixing bolts between the clutch hydraulic control master cylinder and the pedal bracket
7. Install and replace the parts in the reverse order of the above procedure
Notice:
(1) Be careful not to leak brake fluid onto other objects or paint surface. Clean it immedi-
ately to avoid damage.
(2) Do not damage the seal rubber when installing and removing the pipe and make sure the
installation is correct
(3) Clutch pedal set thread torque : 20~25N.m
(4) Clutch hydraulic control master cylinder set bolt torque : 20~25N.m
(5) Torque of the union thread connecting the pipe and clutch master cylinder:
12~16N.m
(6) Torque of the threaded connector connecting the clutch hydraulic hose and pipe:
12~16N.m
(7) Bleed the air in the clutch hydraulic control system
(8) Check the clutch hydraulic control system for leakage
(9) Check the clutch hydraulic control system for reliable working
(10)Check the brake fluid level. Fill the brake fluid of the same brand if necessary.
(11) Check the clutch pedal installation height stroke and free stroke
a . The clutch pedal installation height: 180~186 mm
b . The clutch pedal stroke: 134~142mm
c . The clutch pedal free stroke: 10~20 mm

10110. Remove the snap ring on the spline shaft end of the tripod constant velocity joint
Notice: Do not damage the snap ring, or it shall be replaced
11.Disassemble the Rzeppa Constant velocity universal joint boot Use screwdriver to loosen the
Rzeppa Constant velocity universal joint boot band, remove the boot
Notice: Replace the band if it is distorted
12. Disassemble the Rzeppa Constant velocity universal joint
(1) Remove the old grease
(2) Use the mark pen to make a matchmark on the inboard and outboard joint
Notice: Do not punch the marks
13. Installation is in the reverse order of removal procedure
Notice:
(1) Apply proper amount of long life grease as specified when assembling the tripod
velocity universal joint and Rzeppa Constant velocity universal joint, and then
assemble it according to the matchmark.(2) Keep both sides of the spline shaft clean, the boot intact and the band assembled into place(3) The tripod constant velocity joint spline shaft and the differential shall be assembled into place, with the snap ring opening facing down, use rubber hammer to tap it
appropriately when necessary
(4) Propeller shaft attaching nut torque: 145~155N.m, install the cotter pin
(5) Steering knuckle lower swing arm assembly ball stud pin retaining bolt and nut
torque: 80~90N.m
(6) Tie rod ball stud pin attaching nut torque:27~39N.m, install the cotter pin

102(7) Install front wheel, wheel nut torque: 95~115N.m
(8) Make sure that the propeller shafts for 1.3L engine and 1.5L engine are not interchanged
at the time of replacement
(9) Check the ABS sensor signal, check and adjust the front wheel alignment if necessary.

106Section 3 Front Wheel AlignmentAdjustment1. Inspect tire
2. Inspect toe-in
Toe-in
If the toe-in is not as specified, adjust the tie rod (but the left and
right tie rods must be adjusted symmetrically).
3. Adjust toe-in
(1) Loose the tie rod end lock nut.
(2) Turn the left and right tie rod in the same direction for same
revolutions.
Hint: Adjust the toe-in to the specified value.
Only adjust the one-side tie rod is not allowed.
(3) Make sure the left and right tie rods are of the same length.
(The difference should be less than 0.5mm).
(4) Tighten the lock nut of tie rod.
Torque: 45~50N.m
4. Inspect wheel limited turn angle
Turn the steering wheel fully and measure the turning angle.
Wheel angle:
If the wheel angle is less than the specified value, check whether the length of the right and left tie rod
ends.Tire Pressure 220KP a
Toe-in C-D: 0±3mmInside whe e l a ngle 37.6°
Outside whee l a ngle 33.3°FrontFrontTurn Left Inner
Outer

1096. Disassemble the front strut assembly
(1) Remove the nut on the shock absorber.
Notice: the elasticity of the spring is recovered!
(2) Remove the washer, collar, shock absorber mount seat and big washer.
(3) Remove spring upper seat, front coil spring , front shock absorber boot, front dumper, front coil spring
lower insulator.
7. Assemble the front strut assembly
The assembly of the front strut assembly is in the reverse order of disassembly.
Notice:
(1) Use special fixture when installing the nut on the shock absorber piston rod, be
careful not to let the spring rebound. Torque: 80~90 N.Sm.(2) Install the 4 bolts attaching the front strut assembly to the body. Torque: 25~30N.m.(3) Install the 2 bolts and nuts of the front strut assembly and the brake.
Torque: 90~100N.m.
(4) Install the attaching nuts on the stabilizer bar link rod assembly and shock absorber.
Torque: 50~60N.m.
(5) Install the ABS sensor and secure the signal wire.

1123. Remove lower swing arm front support frame
Remove the 4 bolts connecting the lower swing arm front support frame and vehicle body.
4. Disassemble lower swing arm assembly
Disassembly of lower swing arm assembly is in the reverse order of the assembly.
Notice: Do not tighten type 1 hexagon nut
5. Install lower swing arm front support frame
Attach the lower swing arm front support frame to the vehicle body with bolts .
Torque: 80~90N.m
6. Install lower swing arm assembly
(1) Install the bolts and nuts connecting the lower swing arm assembly and lower swing arm front support
frame.
Notice: Do not tighten the bolts
(2) Attach the left lower swing arm assembly ball stud pin to the steering knuckle with bolts and nuts.
Torque: 80~90N.m
(3) Install the attaching bolt between the lower swing arm rear spring joint cover and the body.
Torque: 80~90N.m
7. Set nut
(1) Lower the vehicle and center the front wheel.
Be careful of the security
(2) Tighten the bolts connecting lower swing arm assembly and lower swing arm front support frame
Torque: 90~100N.m
(3) Tighten the set nuts on the lower swing arm assembly rear spring joint
Torque: 90~100N.m

114ReplacementHint
1. Remove the stabilizer bar left link rod
(1) Remove the nuts connecting the stabilizer bar left link rod and front shock absorber.
(2) Remove the nut connecting the stabilizer bar left link rod and the left side of stabilizer bar.
2. Remove the front stabilizer bar
Remove the 4 bolts, front stabilizer bar rubber bushing, front stabilizer bar clamp.
3. Remove the front stabilizer bar left support frame welding assembly
Remove the nuts connecting the stabilizer bar left support frame welding assembly and vehicle body.
4. Install the front stabilizer bar support frame welding assembly
Set the front stabilizer bar support frame welding assembly to the vehicle body with bolts.
Torque: 50~60N.m