2008 GEELY CK %27

2272. The radio backlight does not light up with the illumination switch ON
Wiring Diagram
(1) Check radio assembly (TAIL)
Check the voltage between terminals under each operating condition as shown in the table below.
Standard:
Abnormal:Repair or replace wire harness and connector
Normal:Check and replace radio assemblyMain Fuse BoxRadio and CDFusible Link Box
BatteryLight
Control
Switch
BatteryTeste r Connec tion Condition Sta nda rd Sta tus
TAIL - GND Combined Switch (Light switc h) 10～
14V

2327. Poor sound quality only when playing tape
(1) Replace it with another tape and re-check
yReplace the faulty tape with working tape to see if the same fault will re-occur.
Standard: The fault is cleared
Normal:There is something wrong with the tape
Abnormal:Check for foreign object
(2) Check for foreign object
yCheck the radio assembly and the cassette player for foreign objects or defects.
Abnormal:Clean foreign objects
Normal:Clean the magnet head and check operation
(3) Magnet Head Cleaning
1Raise the cassette door with your finger. Next, using a pencil or similar object, push in the guide.
2Using a cleaning pen or cotton applicator soaked in cleaner, clean the magnet head surface, pinch rollers
and tape press wheel.
3Check if the same fault reoccurs.
Normal:The magnet head is dirty
Abnormal:Check and replace radio assembly
8. Tape jammed, malfunction with tape speed or auto-reverse
(1) Check for foreign objects
yCheck the radio assembly and tape player for foreign objects and defects
Standard: No foreign objects or defects
Abnormal:Clean foreign objects
Normal:Replace it with another tape and re-check
(2) Replace it with another tape and re-check
yReplace the faulty tape with working tape (less than 90min) to see if the same fault will re-occur.
Standard: The fault is cleared.
Normal:There is something wrong with the tape
Abnormal:Clean the head
(3) Clean the magnet head
1Raise the cassette door with your finger. Next, using a pencil or similar object, push in the guide.
2Using a cleaning pen or cotton applicator soaked in cleaner, clean the magnet head surface, pinch rollers
and capstans.
3Check if the same fault reoccurs.
Normal: The head is dirty
Abnormal: Check and replace radio assembly

2435. Servicing operation shall be carried out 60s after the negative
(-) terminal cable is disconnected from the battery. In addition,
the disconnected negative (-) terminal cable shall be protected
with insulating tape for insulation.
In order to deploy an airbag within a certain time period after the
battery is disconnected, condenser in the ECU shall retain some
electrical energy. Otherwise, it could lead to a serious accident
because of the unexpected deployment of airbag.
6. During spray paint work, ECU, airbag assembly, clock spring
assembly, etc shall be removed and kept in place to avoid the effects of overheat. (Over 93¡æ)
7. When the SRS is serviced, a diagnostic scan meter is used to clear the DTC to enable the normal work of
the warning light.1 1 D AB Lo D r iv er a ir b ag , lo w p o s it io n
13 (Option) PAB Hi Passenger airbag, high position
14 (Option) PAB Lo Passenger airbag, low position
20Passenger Airbag Deactivation
Indic atorPassenger airbag deac tivation indic ator light
27PPD/ Passenger Airbag
Deac tivation Sw itch, HighPassenger airbag deac tivation sw itc h, high position
30 Crash Output Crash outputInsulating TapeBatteryCableDriver Side
Warning LampPassenger Side
Warning LampDriver Seat Inflation
Element & AirbagCrash Sensor &
Diagnostic ModuleFront/RH Inflation
Element & Airbag

246 The transmit of the DTCs are carried out in the way that the SRS ECU (HAE2.5) via serial data interface
of the maintenance procedures assign the codes to the diagnostic detector.23 C ommunication trouble Y e s
24 Inte rna l trouble (se e the follow ing ta ble )No (replace SRS ECU (HAE2.5))
25PADS （
passenger airbag deactivation
sw itch）
, connected to power source or open
circuitYes
26PADS （
passenger airbag deactivation
sw itch）
, ground or short c irc uitYes
27 PADS (passenger airbag switch), trouble Yes
28 C ra sh output pin, ground Y e s
29C ra sh output pin, short c irc uite d to pow e r
sourceYes
30PADI (passenger airbag deactivation switch
indic ator light) error, c onnected to pow er source
or light bulb short c irc uitYes
31PADI (passenger airbag deactivation switch
indic a tor light) e rror, ground or ope n c irc uitYes
32 Se a t be lt pre te nsione r se pa ra te ignition Y e s, up to 5 time s
33Se a t be lt pre te nsione r se pa ra te ignition for 6
time sNo (replace SRS ECU (HAE2.5))No. Trouble De sc ription DTC
1 Ignition c irc uit 1 (drive r a irba g), high re sistanc e or ope n circ uit B1 346
2 Ignition c irc uit 1 (drive r a irba g), low re sista nc e or short c irc uit B1 347
3 Ignition c irc uit 1 (drive r a irba g), groundB1 348
4 Ignition c irc uit 1 (drive r a irba g), c onne cte d to powe r sourc e B1 349
5 Ignition c irc uit 2 (pa sse nge r a irbag), high re sista nc e or ope n c ircuit B1 352
6 Ignition c irc uit 2 (pa sse nge r a irbag), low resista nce or short c irc uit B1 353
7 Ignition c irc uit 2 (pa sse nge r a irbag), groundB1 354
8 Ignition circuit 2 (passenger airbag), connected to power source B1 355
9 Ignition c irc uit 3 (drive r se a t belt pre te nsione r), high re sista nc e or ope n c ircuit B1 361
10 Ignition c irc uit 3 (drive r se a t belt pre te nsione r), low resista nce or short c irc uit B1 362
11 Ignition c irc uit 3 (drive r se a t belt pre te nsione r), ground B1 363
12 Ignition c irc uit 3 (drive r se a t belt pre te nsione r), c onne c t to power sourc e B1 364
13Ignition c ircuit 4 (passe nger se a t be lt pre tensione r), high re sista nc e or open
circuitB1 367 Diagnostic DTCs

247(2) Internal troubles
The micro controller can check the following items not
only in the initiation check but also in the circular diagnos-
tic check.
1Trigger transistor of ignition circuit: high-end transistor
can be checked not only in the initiation check but
also in the circular diagnostic check. However, since
the low-end transistor is open when connected in short
circuit to power source, it can only be checked in the
initiation check to avoid explosion.
2The ignition voltage is provided by supercharge
converter.
3The acceleration sensor performs selfcheck in the
initiation check.
4Range of allowed deviation of acceleration sensor in the circular diagnostic check.
5Microcontroller includes AD converter, ROM, RAM, etc.
6Status of safety sensor.NOTICE
The connectors of the squib circuit contain a
shorting bar. When the connector is not
connected, the unexpected deployment is
caused by the short in the circuit arising from
the contact of the positive (+) and negative (-)
terminals or the static electricity. If there is
poor connection for connectors, the symptom
may not be removed even when the shorting
bar is connected.14Ignition c irc uit 4 (passe nger se a t be lt pre tensione r), low re sistanc e
or short c irc uitB1 368
15 Ignition c ircuit 4 (passe nger se a t be lt pre tensione r), groundB1 369
16Ignition c ircuit 4 (passe nger se a t belt pre te nsione r), c onne c t topowe r sourceB1 370
17 High volta ge of powe r sourc e B1 111
18 Low volta ge of power sourc e B1 112
19Warning light trouble -c onne c te d to powe r sourc e or light bulb short
circuitB2 500
20 Warning light trouble -ground or filame nt ope n circ uitB2 500
21 Missing/mistake of the algorithm parameters B1 661
22 Previous crash recordedB1 650
23 Communic a tion trouble B1 407
23 Inte rna l trouble (se e the following ta ble) B1 620
24PADS（
pa ssenge r airba g de a ctiva tion switch）
, c onne c ted topowe r source or open c irc uitB1 527
25PADS（
passenger airbag deactivation switch）
, ground or short
circuitB1 528
26 PADS (passenger airbag deactivation switch), trouble B1 529
27 Cra sh output pin, groundB1 676
28 Cra sh output pin, short c irc uite d to power sourc e B1 677
29PADI (passenger airbag deactivation switch indicator light) error,
c onne c ted to powe r sourc e or light bulb short c irc uitB2 505
30PADI (passenger airbag deactivation switch indicator light) error,
ground or open c irc uitB2 505
31 Se a t be lt pre tensione r se pa ra te ignitionB1 657
32 Se a t be lt pre tensione r se pa ra te ignition for 6 time s B1 658

2702Prepare two 6m plus wire harnesses for deployment, connect the other two ends to avoid unexpected
deployment in case of static electricity (see the figure below).
3Touch the body of the vehicle with hands for static electricity elimination.
NOTICE:
The above-mentioned procedures can prevent the unexpected deployment due to static electricity and shall
therefore be performed strictly.
4Cut off the wire harnesses of the driver airbag assembly and connect them with the two wire harnesses
for deployment, and make sure to wrap up the connecting location with insulating tape for insulation (see
the figure below).
5Install the unused bolts on to the inside bolt of the driver airbag assembly, and tie a thick wire securing the
wheel rim.
6Pass the deployment wire harness of the driver airbag assembly through an old tire with rim, and fix
upwards the driver airbag assembly by means of the wire connected to the bolts, etc (see the figure
below).Wire Harness
for DeploymentShort Circuit Location6m plusPassenger AirbagWire Harness
for DeploymentShort
Circuit
Location
Insulating TapeAirbag AssemblyWire Harness for Deployment

2717Put three old tires without hubs onto the tire used to fix the driver airbag assembly (see the figure below).
8Try to disconnect at a location far away from the vehicle the connector of the wire harness for deployment
of the driver airbag assembly, connect with the two terminals of the battery removed from the vehicle
and deploy the airbag (see the figure below).
9the deployed driver airbag assembly shall be scrapped according to the scrapping procedures.Wire Harness for DeploymentOld Wheels
without HubWire Harness
for DeploymentNOTICE
Make sure to deploy the driver airbag assembly when there is no person close by.After the driver airbag is deployed, the gas generator is of high temperature. Keep it for over 30 minutesuntil it gets cool for use

272Chapter 8 MK-20 ABS SystemSection 1 ABS DiagnosisI. Check the ABS Warning Light1. Check the ABS Warning Light goes on as the following:
1Turn the ignition switch to ON, the ABS Warning Light goes on for about 1.7 seconds and then goes off.
2If the above condition is not satisfied, it indicates that there is a fault, please check the DTC.
3If the warning light does not light up at all, refer to the Non-DTC fault inspection table.II. The Reading of the information statusAfter connecting the scan meter, turn the ignition switch to¡°ON¡±, select the function menu item 01, press
OK to confirm, the screen will display the following information:
1. ECU drawing number and its version:
ABS MK20 IE
2. Code 01901III. Read and Clear the DTC1. After selecting the "02 Read DTC" in the function menu, it displays the total amount of the fault, if there
is no DTC, then it displays no DTC. Then, press OK button to proceed to next page to review the DTC
and its description. Generally, there is a P or O before the DTC, indicating that it is a Persistent fault or
Occasional fault. Persistent fault remains existing all the time, while the Occasional fault can be cleared
and is only able to reoccur during the driving.
Note:
The reading of the DTC can not be quitted middle way, you can return to the function menu only
after reading all the DTC.
Clear DTC
2. Select function menu item 05, press OK button to clear the DTC, if the DTC can not be cleared, it
indicates that the DTC represent exist all the time, if the saved DTC can be cleared, it indicates that it is
occasional fault can only be detected during the driving.