2008 GEELY CK instrument panel

308Section 6 Basic System1. Blower Removal / Installation
1. Disconnect the negative (--) terminal cable from the battery.
2. Remove instrument panel.
3. Remove motor connector.
4. Remove the resistor connector.
5. Remove the band.
6. Remove bolt. Remove blower.
7. The installation is in the reverse order of the removal.
2. Heater Removal / Installation
1. Remove water hose No. 1 and 2.
2. Remove instrument panel.
3. Remove the band.
4. Remove 2 wind door cables.
5. Remove heater.
6. The installation is in the reverse order of
the removal.
3. The Evaporator Removal / Installation
1. Remove evaporator inlet and outlet pipeline.
2. Remove instrument panel.
3. Remove thermistor connector.
4. Remove 2 bands.

320(III) Front inside trim613
7 Front door power window switc 14Elec tric outs ide rear view mirr or 5 Instrument panel end shield 12 Auxiliary console assembly 3 A/C panel assembl 10
411 1 A- pillar in s ide t r im 8
29
Low er en d s hield as s em b ly
Front row seat Front door insdie trim
Instrument panel assembly
Glove c ompartment as s embly
Steering column coverFront door sill inside trim
Front end of auxiliary c onsole

338(VIII) Instrument panel and auxiliary console1. Instrument Panel Removal / Installation(1) Disconnect the negative (--) terminal cable from the
battery.
(2) Remove the instrument panel compartment.
(3) Remove the front and rear auxiliary console.
(4) Remove combination meter panel.
(5) Remove instrument cluster.
(6) Remove the steering column cover.
(7) Remove the undercover.
(8) Remove the steering column.
(9) Remove A pillar frame.
(10) Remove intermediate instrument panel.
(11) Remove right side shield.
(12) Remove left side shield.
(13) As to the vehicle installed with A/C control mechanism, disconnect the front A/C wire.
(See the removal and installation of A/C control mechanism)
(14) Disconnect the instrument panel wire harness connector.
(15) Remove the bolt.
(16) Take out the instrument panel from the open driver side door.
(17) The installation is in the reverse order of the removal.
Warning
It is dangerous to remove the instrument panel before supporting it. The instrument panel may
drop and result in body injury. Have at least one assistant for help to implement the procedures.
Remove the supporting pin from the vehicle body to remove the instrument panelPin

3392. Instrument Panel Removal/Installation(1) Remove the airbag actuator at the driver side.
(2) Remove the intermediate instrument panel.
(3) Remove the audio device
(4) Remove A/C control mechanism.
(5) Remove in the order below in the figure.
(6) The installation is in the reverse order of the removal.
Torque: 18.6--25.5 N.m1 instrument panel w ire harness
2 instrument panel c ross member3instrument panel 123

3403.Side Panel Removal/Installation
(1) Using the flat screwdriver wrapped with vinyl tape, disconnect the
clip.
(2) Pull the side panel towards yourself and remove the plate from the
instrument panel and remove the side panel.
(3) The installation is in the reverse order of the removal.
4.Steering Column Cover Removal/Installation
(1) Remove upper cover.
(2) Remove the ignition key.
(3) Remove the screw.
(4) Remove lower cover.
(5) The installation is in the reverse order of the removal.
5.Combination Instrument Panel Removal/Installation
(1) Remove the screw.
(2) Using the flat screwdriver wrapped with vinyl tape, disconnect the clip.
(3) Pull combination instrument panel towards yourself. Remove pillar.
(4) The installation is in the reverse order of the removal.
6.Lower End Shield Removal/Installation
(1) Using the flat screwdriver wrapped with vinyl tape, disconnect the
clip.
(2) Pull the lower end shield towards yourself and remove clipA and
plate B from the instrument panel and remove lower end shield.
(3) Disconnect the engine hood cable.
The installation is in the reverse order of the removal.

3417.Intermediate Instrument Panel Removal/Installation
(1) Disconnect the negative (--) terminal cable from the battery.
(2) Remove intermediate instrument panel.
(3) Remove the screw.
(4) Using the flat screwdriver wrapped with vinyl tape, disconnect
the clip.
(5) Pull the intermediate instrument panel forward and then remove
the clip.
(6) Remove LDC (Liquid Crystal Display) component connector.
(7) The installation is in the reverse order of the removal.
8.Glove Compartment Removal/Installation
(1) Open the glove compartment;
(2) Pull the glove compartment up and separate it from the instrument panel;
(3) The installation is in the reverse order of the removal.

3616. Cowl Upper Assembly
Cowl upper assembly is mainly composed of cowl upper outer plate, cowl upper LH/RH end plate assembly,
instrument panel mounting plate, steering column mounting bracket upper/lower plate, cowl lower inner plate,
ventilator cover, etc., by welding them together.
Figure 5-2 Dismantle diagram of front sheet metal and cowl parts
1 Front Cross Member 2 Hood Lock Bracket Assy. 3 LH/RH Side Member End Plate
4 Engine Hood Front Support Plate Assy. 5 LH/RH Front Cross Member 6. LH/RH Front Mud Guard
7 Front Cross Member Assy. 8 Cowl Inner And Outer Plate Assy. 9 LH/RH Front Mud Guard
Reinforcement 10 Cowl Upper Baffle12 375683910 64Front

366II. Removable Sheet Metal Parts
(I) Engine Hood, Front Fender1. Engine hood is mainly used to protect the engine, meet the whole vehicle design, and make the mainte-
nance convenient. It also has an effect of isolating the engine noise. The engine hood has a double-insurance
lock system. The release of the first lock is controlled by the drawing cable that is under the instrument panel.
As to the release of the second lock, you should firstly release the first one and the hood will open, and then
move the hood lock hook. The double-insurance lock system is designed for safety, especially in the course
of running with a high-speed, to prevent the engine hood from being raised, which often causes traffic
accidents. The angle of the hood that is fully opened is 52°.As shown in Figure 5-8
Figure 5-8 Engine Hood Hinge
1Hinge Bracket 2 Hinge Arm 3 Pin Shaft(II) Front FenderThe matching relationship between the front fender and hood, front door is as shown in the Figure 5-9.
Figure 5-9 Section Around The Front Fender
A) The matching relationship with the hood (5mm ± 0.5mm)
B) The matching relationship with the front door (5mm ± 0.5mm) 13252
†while fully open
Engine Hood
outer plate
Engine Hood
inner plate
AEngine HoodFront fender
Front door
Front fender
B