2008 DODGE VIPER brake

A WORD ABOUT YOUR KEYS
You can insert the double-sided keys into the locks with
either side up.
The dealer that sold you your new vehicle has the key
code numbers for your vehicle locks. These numbers can
be used to order duplicate keys from your dealer or a
locksmith. Ask your dealer for these numbers and keep
them in a safe place.
Ignition Key Removal
1. Press the clutch pedal to the floor.
2. Bring the vehicle to a stop.
3. Place the gear selector in gear.
4. Apply the parking brake fully.5. Press the ªKey Removalº release button, turn the key
to place the ignition switch in the OFF/LOCK position,
and then pull the key out of the switch.
6. Release the clutch pedal.
Ignition Key Positions
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

ON/RUN position. If not deactivated through the trans-
mitter or the ignition switch, the alarm will turn off
automatically after 3 minutes.
Programming Additional Transmitters
NOTE:You must have at least one programmed trans-
mitter to perform this procedure. If you do not have a
programmed transmitter, contact your dealer for details.
Use this procedure to program up to three additional
transmitters for your vehicle. To activate the program-
ming feature, proceed as follows:
1. Turn the ignition switch to the ON/RUN position.
2. Set the parking brake.
3. Press and hold the UNLOCK button for at least 5
seconds, but no longer then 10 seconds on a previously
programmed transmitter. Then, press the PANIC button
while still holing the UNLOCK button.4. Release both buttons at the same time. A chime will
sound to signal that the programming feature is acti-
vated.
5. Within 30 seconds, press and release the LOCK button
and the UNLOCK button at the same time on the new
transmitter.
6. Press and release any button one time on the new
transmitter. A chime will sound to indicate that the new
transmitter is programmed. An additional chime will
sound at the end of the 30-second programming period.
It will also sound if the ignition is switched OFF.
7. Repeat Steps 3 through 6 to program each additional
transmitter.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WINDOWS
Power Windows
The power window switches are located between the
driver and passenger seats on the center tunnel bezel, just
to the left of the parking brake. The switch on the left side
controls the driver's window and the switch on the right
controls the passenger's window. The power window
switches are active when the ignition is in ON/RUN or
ACC position.
NOTE:
²The Power Accessory Delay feature allows you to
operate the power windows for 2 minutes after turn-
ing off the ignition switch. Removing the key from the
ignition switch and opening the driver's door will
cancel this feature. Your dealership can enable or
disable the Power Accessory Delay feature as desired.
²Windows cannot be driven up during Power Acces-
sory Delay with a door open. Furthermore, opening
the door will stop the window movement immediately
if the window is in the process of going up.
²The window will lower slightly if it is closed com-
pletely when opening the door. The window will
return to its fully closed position after closing the door.
This action is necessary in order to clear the seal when
opening the door.
WARNING!
Never leave children in a vehicle, with the keys in the
ignition switch. Occupants, particularly unattended
children, can become entrapped by the power win-
dows while operating the power window switch. Such
entrapment may result in serious injury or death.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

LIFTGATE Ð COUPE MODELS ONLY
The liftgate can be unlocked or locked by the Remote
Keyless Entry (RKE) transmitter or by activating either of
the power door lock switches located on the door trim
panels.
To unlock the liftgate with the RKE transmitter, press the
LIFTGATE button on the transmitter for at least one
second. The park lights and turn signal lights will flash
three times to acknowledge the signal.
NOTE:Pressing the UNLOCK button on the transmitter
will also allow liftgate access.
Once unlocked, the liftgate can be opened or closed. To
open the liftgate, depress the liftgate release switch
located in the exterior liftgate handle and pull the liftgate
open with one fluid motion.
NOTE:The liftgate release switch will be ignored under
the following conditions:
²When the ignition is in RUN and the parking brake is
not set.
²When vehicle speed is not a 0 mph (0 km/h).
²When all doors are locked (except for RKE liftgate
access). Refer to ªEntering the liftgate with the System
Armed Ð Coupeº under ªSecurity Alarm Systemº in
this section for additional information.
The word ªDECKº will flash in the odometer when the
liftgate is open. With the key in the ignition switch, this
display will turn off approximately 40 seconds after
switching off the ignition, or if the Power Accessory
Delay feature is active, it will turn off approximately 40
seconds after the delay feature times out.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

This feature can be disabled at the dealership, if so
desired.
Daytime Running Lights
The fog lights will come on as Daytime Running Lights,
whenever the ignition switch is on, the headlights are off,
and the parking brake is off. The headlight switch must
be used for normal night time driving.
NOTE:This feature is standard on all Canadian vehicles
and cannot be disabled. For US vehicles, this feature is
shipped disabled and can be enabled or disabled at a
dealership, if so desired.
Lights-On Reminder
If the headlights or parking lights are on and the ignition
switch is turned off, a chime will sound when the driver's
door is opened to alert the driver.
Battery Saver Feature Ð Exterior Lights
To protect the battery, the exterior lights will turn off
automatically 3 minutes after the ignition switch is
turned off. To restore exterior light operation, either turn
the ignition switch on or cycle the headlight switch.
Fog Lights
To activate the front fog lights, turn on the parking
lights or the low beam headlights and pull out on
the end of the Multi-Function Lever.
NOTE:The fog lights will only operate with the head-
lights on low beam. Selecting high beam headlights will
turn off the fog lights.
Turn Signals
Move the Multi-Function Lever upward or downward
and the corresponding turn signal indicator on the in-
strument panel will flash to show proper operation of the
front and rear turn signal lights.
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!
Tilting the steering column while the vehicle is
moving is dangerous. Without a stable steering col-
umn, you could lose control of the vehicle and have
an accident. Adjust the column only while the ve-
hicle is stopped. Be sure it is locked before driving.
ADJUSTABLE PEDALS
This feature allows the driver to move the brake and
accelerator pedals about 3 inches (72 mm) forward or
rearward to allow for greater driving comfort. The Ad-
justable Pedals switch is recessed into the knee bolster
beneath the steering column.
Adjustable Pedal Switch
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

²The word ªDECKº will flash in the display if the
trunk/liftgate is open.
²The words ªLOW TIREº will flash slowly in the display
and a chime will sound if the tire pressure is low.
²The words ªFLAT TIREº will flash rapidly in the
display and a chime will sound if critically low tire
pressure is detected.
Message Center
When the appropriate conditions ex-
ist, the Message Center displays the
following indicators and warnings:
High Beam Light
This light will turn on when the high beam
headlights are on. Pull the Multi-Function Leveron the left side of the steering column toward you to
switch the headlights from low beam to high beam. Pull
the lever a second time to switch the headlights back to
low beam. (See page 81 for more information.)
Front Fog Light Indicator
This light will turn on when the front fog lights are
on. (See page 82 for more information.)
Anti-Lock Brake Warning Light
The amber Anti-Lock Brake Warning Light will
turn on and stay on briefly as a bulb check
when the ignition is first turned on. If the light
does not turn on during starting, see your
authorized dealer for service.
This light also illuminates at vehicle start-up to indicate
that the ABS self-check is in process. If the light remains
on after start-up, or turns on and remains on at road
speeds, it may indicate a system malfunction or that the
system is inoperative. In this case, the system reverts to
UNDERSTANDING YOUR INSTRUMENT PANEL 97
4

standard non-anti-lock brakes. If this occurs, safely bring
the vehicle to a complete stop as soon as possible and
cycle the ignition key to attempt to reset the ABS. If the
light remains on, see your authorized dealer immediately
to have the system serviced. Furthermore, if the red
BRAKE warning light and the amber ABS warning light
are on, and the parking brake is fully released, see your
authorized dealer immediately. (See page 147 for more
information.)
WARNING!
If the ABS and/or Brake Warning lights illuminate,
please seek service immediately! Your vehicle will
have diminished braking capability and control if ABS
and/or service brake systems are not working properly.
Have your brake system serviced immediately.
Malfunction Indicator Light
This light is part of an onboard diagnostic
system called OBD. The OBD system monitors
engine control systems. The light will turn on
when the key is in the ON/RUN position
before engine start. If the light does not come on when
turning the key from OFF/LOCK to ON/RUN, have the
condition checked promptly.
Certain conditions such as a loose or missing gas cap,
poor fuel quality, etc. may illuminate the light after
engine start. The vehicle should be serviced if the light
remains on through several of your typical driving
cycles. In most situations, the vehicle will drive normally
and will not require towing.
The Malfunction Indicator Light flashes to alert you to
serious conditions that could lead to immediate loss of
power or severe catalytic converter damage. The vehicle
should be serviced as soon as possible if this occurs. (See
page 195 for more information.)
98 UNDERSTANDING YOUR INSTRUMENT PANEL