2008 DODGE SPRINTER reset

242 Controls in detailAuxiliary heating/ventilation*
3
\1
Press the
æ
or
ç
button to se-
lect the desired switch-on time. The
automatic switch-on is deactivated if
the
Timer off
setting is selected.
\1
Press the
è
button.
The switch-on time is selected.
The yellow indicator lamp in
the
ö
switch comes on.
Setting the switch-on time
Operating system without steering
wheel buttons
\1
Select a switch-on time as described
under “Selecting a switch-on time”
(\2
page 240).
\1
Press the reset button on the
in-
strument cluster to set the selected
switch-on time.
The hours figure flashes and
the
”
symbol appears in the dis-
play.
\1
Set the hours using the or

am
button on the
instrument cluster.
\1
Press the reset button.
The minute display flashes.
\1
Set the minutes using the
or button.
iYou can reach the
Aux. heat.
sub-
menu via the
Settings
menu
(
\2
page 161).
iIf you turn the key to position
0 in the
ignition lock, the yellow indicator
lamp in the
ö
switch goes out af-
ter 30 minutes.
The red indicator lamp in the
ö

switch comes on when the auxiliary
heating switches on.
nf_BA.book Page 242 Friday, January 25, 2008 3:53 PM

245 Controls in detail
Open air
3
Resetting the side windowsThe side windows must be reset if the
battery has been disconnected:\1
Pull the two power window switches
until the side windows are closed.
\1
Hold the switches in this position for
about 1 second.
The side windows are reset.
Sliding sunroof*Warning
G
Make sure that nobody can become
trapped as you close the sliding sunroof.The glass may shatter in the event of an
accident.If you or other occupants are not wearing
your seat belt, there is a risk of being
thrown out of the opening in the event of
the vehicle overturning. Therefore, always
wear a seat belt to reduce the risk of inju-
ries.
Continued
Warning (Continued)
G
In accidents in which the vehicle over-
turns, there is an increased risk of injury
even for occupants who have fastened
their seat belts correctly, as their head or
limbs could be thrust through the open-
ing.Remove the key from the ignition lock
even if you are only leaving the vehicle for
a short time.
nf_BA.book Page 245 Friday, January 25, 2008 3:53 PM

247 Controls in detail
Open air
3
Resetting the sliding sunroofThe sliding sunroof must be reset after:\4
the sunroof has been closed manual-
ly using the emergency operation
key (
\2
page 522)
\4
the sunroof has opened with a jerk
\4
a malfunction
\1
Switch on the ignition (
\2
page 111).
\1
Press the sliding sunroof switch in
the direction of arrow
2
(\2
page 246).
\1
Wait until the sliding sunroof is
closed and then keep the sliding sun-
roof switch pressed for approximate-
ly 3 seconds.
The sliding sunroof is reset.The roof ventilator can be used to venti-
late or remove air from the load com-
partment.
The switch is between the light switch
and the steering wheel.
1To ventilate the load compartment (air out)
2To ventilate the load compartment (air in)
\1
Switch on the ignition (
\2
page 111).
\1Air out:
press upper part
1
of the
switch.
The roof ventilator removes used air
from the load compartment.
\1Air in:
press lower part
2
of the
switch.
The roof ventilator feeds fresh air
into the load compartment.
\1To switch off:
set the switch to the
center position.
Roof ventilator in the load
compartment*
N54.25-2929-31
nf_BA.book Page 247 Friday, January 25, 2008 3:53 PM

273 Controls in detail
Operating the vehicle
3
\3 Operating the vehicleWhen activated, the operating speed
governor (ADR) automatically increases
the engine speed to a preset or adjust-
able operating speed (
\2
page 275).
Activating / deactivating ADRThe switch is between the light switch
and the steering wheel.1To switch on
2To switch off
Operating speed governor (ADR)*
iThe idle speed of the engine auto-
matically increases after a cold start.
If the set operating speed is lower
than the increased idle speed, the
set operating speed is attained only
after the engine has reached its op-
erating temperature.
It is only possible to activate ADR
with the vehicle stationary and the
handbrake applied. The selector le-
ver must be in position
P.
N54.25-2932-31
nf_BA.book Page 273 Friday, January 25, 2008 3:53 PM

338 OperationBattery isolating switch*
4
\3 Battery isolating switch*You can disconnect the current to all
your vehicle’s consumers using the bat-
tery isolating switch. This will prevent
uncontrolled battery discharge caused
by quiescent current consumption.
The battery isolating switch is to the
right of the accelerator pedal in the driv-
er’s footwell.
1Connector
2Slide
Warning
G
If the vehicle is equipped with an auxiliary
battery in the engine compartment, it is
necessary to disconnect both batteries
when working on the vehicle electrical
system. Only then is the electrical system
fully disconnected from the power supply.
iOnly disconnect the vehicle electrical
system from the power supply using
the battery isolating switch if the ve-
hicle is to be parked up for a long pe-
riod or when this is absolutely
necessary.
After the power supply is switched
on, you must reset the electric sliding
door (
\2
page 92).
nf_BA.book Page 338 Friday, January 25, 2008 3:53 PM

380 OperationTires and wheels
4
\1
Press button
è
or
ÿ
on the
multifunction steering wheel repeat-
edly until the standard display menu
appears in the multifunction display
(
\2
page 157).
\1
Press the
j
or
k
button re-
peatedly until you see the current in-
flation pressures for each tire appear
in the display or the following mes-
sage appears in the display
Tire pres. displayed
after driving
for several minutes
\1
Press reset button0 on the instru-
ment cluster (
\2
page 20).The following message will appear in
the multifunction display:
Tire pres.
Adjust pres.
\1
Press
æ
button.
The following message will appear in
the multifunction display:
Tire pres. monitor
reactivatedAfter a few minutes' driving, the cur-
rent tire inflation pressure values are
accepted as reference values and
then monitored.If you wish to cancel the activation pro-
cess :
\1
Press
ç
button.
Potential problems associated with
underinflated and overinflated tiresProper tire inflation pressure is essential
to the safe and satisfactory operation of
your vehicle. The following three primary
areas are affected by improper tire infla-
tion pressure:
nf_BA.book Page 380 Friday, January 25, 2008 3:53 PM

412 OperationMaintenance and servicing
4
Service due date display
Vehicles with steering wheel buttonsThe following messages may be dis-
played:\49
Service A in .. days
\49
Service A in .. miles
(km)
\49
Service A due now
The letters
A or
B indicate the type of ser-
vice that is due.
Vehicles without steering wheel
buttonsThe following messages may be dis-
played:\49
for service A
\4´
for service B
The following are also shown:
Service A: Oil Service Plus
Service B: Maintenance Service
\4
the remaining distance in kilometers,
e.g.
1900 miles
(3000 km
)
\4
the remaining time in days, e.g.30 days
.
Missing the service due date An authorized Sprinter Dealer, can reset
the service indicator when the service
has been carried out.
!
CAUTION
If you fail to have the specified ser-
vice carried out, you could be in
breach of relevant regulations and
warranty and goodwill settlements
could be invalidated.
nf_BA.book Page 412 Friday, January 25, 2008 3:53 PM

489 Practical hints
Display messages
5
The operating system shows warnings,
malfunctions or additional information in
the display.
Certain messages are accompanied by a
warning signal or a permanent tone.
High-priority messages are highlighted
in red in the display.
Please respond in accordance with the
messages and follow the additional
notes in these Operating instructions.
\4
Low-priority messages can be ac-
knowledged using the
è
, ·
,
j
or
k
buttons on the steer-
ing wheel or using the reset button
on the instrument cluster
(
\2
page 142). They are then stored
in the malfunction memory.
\4
Highest-priority messages cannot be
acknowledged and are automatically
stored in the malfunction memory.
If you select the Malfunction memory
menu in the operating system
(
\2
page 160), the acknowledged and
unacknowledged messages will appear.
Display messages on vehicles with
steering wheel buttons
Warning
G
No messages can be displayed if there is
a failure of the instrument cluster and / or
the display. You will not then be able to
see information about the vehicle status,
such as speed and outside temperature,
warning and indicator lamps, malfunction
and warning messages or the failure of
systems. Handling characteristics may be
affected.
Continued
nf_BA.book Page 489 Friday, January 25, 2008 3:53 PM